A Full Connectable and High Scalable Key Pre-distribution Scheme Based on Combinatorial Designs for Resource-Constrained Devices in IoT Network

Considering the internet of things (IoT), end nodes such as wireless sensor network, RFID and embedded systems are used in many applications. These end nodes are known as resource-constrained devices in the IoT network. These devices have limitations such as computing and communication power, memory capacity and power. Key pre-distribution schemes (KPSs) have been introduced as a lightweight solution to key distribution in these devices. Key pre-distribution is a special type of key agreement that aims to select keys called session keys in order to establish secure communication between devices. One of these design types is the using of combinatorial designs in key pre-distribution, which is a deterministic scheme in key pre-distribution and has been considered in recent years. In this paper, by introducing a key pre-distribution scheme of this type, we stated that the model introduced in the two benchmarks of KPSs comparability had full connectivity and scalability among the designs introduced in recent years. Also, in recent years, among the combinatorial design-based key pre-distribution schemes, in order to increase resiliency as another criterion for comparing KPSs, attempts were made to include changes in combinatorial designs or they combine them with random key pre-distribution schemes and hybrid schemes were introduced that would significantly reduce the design connectivity. In this paper, using theoretical analysis and maintaining full connectivity, we showed that the strength of the proposed design was better than the similar designs while maintaining higher scalability.

     

Cerebral microbleeds and cognitive decline in a hemodialysis patient: Case report and review of literature

Cerebral microbleeds (CMBs) are small hemosiderin deposits indicative of prior cerebral microscopic hemorrhage and previously thought to be clinically silent. Recent population‐based cross‐sectional studies and prospective longitudinal cohort studies have revealed association between CMB and cognitive dysfunction. In the general population, CMBs are associated with age, hypertension, and cerebral amyloid angiopathy. In the chronic kidney disease (CKD) population, diminished estimated glomerular filtration rate has been found to be an independent risk factor for CMB, raising the possibility that a uremic milieu may predispose to microbleeds. In the end‐stage renal disease (ESRD) population on hemodialysis, the incidence of microbleeds is significantly higher compared with a control group without history of CKD or stroke. We present an ESRD patient on chronic hemodialysis with a history of gradual cognitive decline and progressive CMBs. Through this case and literature review, we illustrate the need to develop detection and prediction models to treat this frequent development in ESRD patients.     

Expression of Main Toll-Like Receptors in Patients with Different Types of Colorectal Polyps and Their Relationship with Gut Microbiota

Abnormal activation of Toll-like receptor (TLRs) signaling can result in colon cancer development. The aim of this study was to investigate the expression of important TLRs in different histological types of colorectal polyps and evaluate their relationship with intestinal microbiota. The expression levels of TLR2, 3, 4, and 5 were analyzed in intestinal biopsy specimens of 21 hyperplastic polyp (HP), 16 sessile serrated adenoma (SSA), 29 tubular adenoma (TA), 21 villous/tubulovillous (VP/TVP) cases, and 31 normal controls. In addition, selected gut bacteria including Streptococcus bovis, Enterococcus faecalis, Enterotoxigenic Bacteroides fragilis (ETBF), Fusobacterium nucleatum, Porphyromonas spp., Lactobacillus spp., Roseburia spp., and Bifidobacterium spp. were quantified in fecal samples using absolute qRT PCR, and, finally, the association between TLRs and these gut microbiota- was evaluated by Spearman’s correlation coefficient. Higher expression of TLR2 and TLR4 in VP/TVP and TA, and lower expression levels of TLR3 and TLR5 in all type of polyps were observed. The differences in TLR expression patterns was not only dependent on the histology, location, size, and dysplasia grade of polyps but also related to the intestinal microbiota patterns. TLR2 and TLR4 expression was directly associated with the F. nucleatum, E. faecalis, S. bovis, Porphyromonas, and inversely to Bifidobacterium, Lactobacillus, and Roseburia quantity. Furthermore, TLR3 and TLR5 expression was directly associated with Bifidobacterium, Roseburia, and Lactobacillus quantity. Our results suggest a possible critical role of TLRs during colorectal polyp progression. An abnormal regulation of TLRs in relation to gut microbial quantity may contribute to carcinogenesis.     

Effects of SiC content on the densification,microstructure, and mechanical properties of HfB2–SiC composites

To investigate the effects of SiC on microstructure, hardness, and fracture toughness, 0, 10, 20, and 30 vol% SiC were added to HfB₂ and sintered by SPS. Upon adding SiC to 30 vol%, relative density increased about 4%; but HfB₂ grain growth had a minimum at 20 vol% SiC. This may be due to grain boundary silicate glass, responsible for surface oxide wash out, enriched in SiO₂ with higher fraction of SiC. By SiO₂ enrichment, the glass viscosity increased and higher HfO₂ remained unsolved which subsequently lead to higher grain growth. Hardness has increased from about 13 to 15 GPa by SiC introduction with no sensible variation with SiC increase. Residual stress measurements by Rietveld method indicated high levels of tensile residual stresses in the HfB₂ Matrix. Despite the peak residual stress value at 20 vol% SiC, fracture toughness of this sample was the highest (6.43 MPa m^0.5) which implied that fracture toughness is mainly a grain size function. Tracking crack trajectory showed a mainly trans-granular fracture, but grain boundaries imposed a partial deflection on the crack pathway. SiC had a higher percentage in fracture surface images than the cross-section which implied a weak crack deflection.     

Duodenal erosions and ulcers in patients with pancreatobiliary obstruction

The authors compared in a controlled clinical study two groups of patients after a first renal transplantation treated by triple drug immunosuppressive therapy. In a group of 31 patients the triple combination comprised Sandimmune Neoral. In the control group there were 30 patients who received Sandimmune. No differences were found between the two groups as regards the effectiveness of this treatment and the authors did not confirm a lower incidence of rejections described in patients treated with Sandimmune Neoral. They confirmed, however, a lower interindividual variability of Cy-A levels assessed specifically in patients treated with Sandimmune Neoral.     

Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

Rotation-invariant multiresolution texture analysis using radon and wavelet transforms.

A new rotation-invariant texture-analysis technique using Radon and wavelet transforms is proposed. This technique utilizes the Radon transform to convert the rotation to translation and then applies a translation-invariant wavelet transform to the result to extract texture features. A kappa-nearest neighbors classifier is employed to classify texture patterns. A method to find the optimal number of projections for the Radon transform is proposed. It is shown that the extracted features generate an efficient orthogonal feature space. It is also shown that the proposed features extract both of the local and directional information of the texture patterns. The proposed method is robust to additive white noise as a result of summing pixel values to generate projections in the Radon transform step. To test and evaluate the method, we employed several sets of textures along with different wavelet bases. Experimental results show the superiority of the proposed method and its robustness to additive white noise in comparison with some recent texture-analysis methods.     

An automated coding and classification system with supporting database for effective design of manufacturing systems

The philosophy of group technology (GT) is an important concept in the design of flexible manufacturing systems and manufacturing cells. Group technology is a manufacturing philosophy that identifies similar parts and groups them into families. Beside assigning unique codes to these parts, group technology developers intend to take advantage of part similarities during design and manufacturing processes. GT is not the answer to all manufacturing problems, but it is a good management technique with which to standardize efforts and eliminate duplication. Group technology classifies parts by assigning them to different families based on their similarities in: (1) design attributes (physical shape and size), and/or (2) manufacturing attributes (processing sequence). The manufacturing industry today is process focused; departments and sub units are no longer independent but are interdependent. If the product development process is to be optimized, engineering and manufacturing cannot remain independent any more: they must be coordinated. Each sub-system is a critical component within an integrated manufacturing framework. The coding and classification system is the basis of CAPP and the functioning and reliability of CAPP depends on the robustness of the coding system. The proposed coding system is considered superior to the previously proposed coding systems, in that it has the capability to migrate into multiple manufacturing environments. This article presents the design of a coding and classification system and the supporting database for manufacturing processes based on both design and manufacturing attributes of parts. An interface with the spreadsheet will calculate the machine operation costs for various processes. This menu-driven interactive package is implemented using dBASE-IV. Part Family formation is achieved using a KAMCELL package developed in TURBO Pascal.