Simulations of the mobile phase of polyethylene

Results are presented from atomistic molecular dynamics simulations of the mobile pseudo-hexagonal phase of polyethylene, which occurs under conditions of elevated pressure and temperature. Three different types of model are considered, all of which employ periodic boundary conditions. The first model consists of n-alkane sequences (48×-C₂₄H₄₈-) that are bonded across the simulation box boundaries to produce chains that are effectively infinite in extent. On heating, at high pressure, this system displays a rotator phase, in which the chains retain an all-trans conformation, and rotate as semi-rigid units. A second model, consisting of finite n-alkanes (48×C₂₄H₅₀) displays the same behaviour at low temperatures, but at high temperature and pressure forms a conformationally disordered rotator phase, characterised by a large proportion of gauche defects and a significant lattice expansion. The final model considered contains long n-alkanes (24×C₁₀₂H₂₀₆) which contain jog defects and each pass twice through the simulation box. This model forms a conformationally disordered rotator phase at high temperature and ambient pressure. The behaviour of the three models, in terms of the variations in chain conformation and rotational and translational dynamics, are compared. The conformationally disordered phases provide useful representations of the experimentally observed mobile phase.     

Effects of manufacturing defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates

The effects of defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates have been measured. The defects studied were cut fibre plies, omission of polymer films and local delamination produced by the inclusion of foreign matter. Of these it was found that only cut plies had a significant detrimental effect on the strength of a laminate. For specimens with two cut plies, the failure stress, tensile, flexural and compressive in the remaining continuous plies was the same as in the defect-free material, provided that the cut plies were widely separated. However the failure stresses were 15–18% lower in the continuous plies in the specimens containing two cut plies which were more closely spaced and in specimens containing four cut plies.     

Transconductance and mobility of Si:B delta MOSFETs

Delta-doped MOSFETs have been fabricated in MBE-grown silicon using for the first time boron as the dopant within the delta layer. Current-voltage characteristics have been measured, and secondary ion mass spectrometry (SIMS) is used to confirm the location of the delta layer and the extent of layer broadening by diffusion during processing. Precise threshold voltages of the devices are difficult to determine since the devices (which all operate in depletion mode) take several volts to switch off. Transconductances of the devices have been measured, and it is shown how analysis of these results can yield estimates of the carrier mobility for transport along the delta layers despite the uncertainty in the threshold voltage. A clear transition is observed in the results which is attributed to the formation of a parasitic surface-channel field-effect transistor, providing conclusive evidence that the devices are conducting along a delta channel for part of the measured range of applied gate biases     

Antigenic variants of Plasmodium chabaudi chabaudi AS and the effects of mosquito transmission

Previous results, using a passive transfer assay, have shown that recrudescences of Plasmodium chabaudi chabaudi AS strain are antigenically different from the infecting parental population and also that the recrudescence appears to be a mix of antigenic types. This present study examines further these recrudescent populations using an indirect fluorescent antibody test on live, schizont-infected red blood cells. This analysis shows that ten clones derived from a recrudescence are all antigenically different from the parent population and that some are different from each other. The use of this method to examine the antigenic types of recrudescent clones after transmission through mosquitoes also demonstrates a resulting change in antigenicity. Such results showing a link between mosquito transmission and varying antigenicity may have important implications in terms of immunity and vaccine development.     

Effect of crosslinking agent content, monomer functionality, and repeat unit chemistry on properties of unfilled resins

Seven mechanical/physical properties were used to evaluate 10 unfilled resins: eight aromatic dimethacrylates and two urethane dimethacrylates. Physical property tests included compressive strength, Young's modulus in compression, uniaxial tensile strength, intrinsic yield point, toothbrush abrasion, Knoop hardness, and water sorption. Controlled changes were made in the following four material parameters: amount of crosslinking diluent present in the uncured monomer, functionality of the monomer, repeat unit chemistry of the monomer (urethane vs. aromatic structure) and mode of activation (chemical vs. visible light). Polymers containing a high concentration of crosslinking agent (50 wt%) were found to be tougher and to possess lower hardness than materials containing lesser amounts of crosslinking agent. This was attributed to the flexible nature of the triethylene glycol dimethacrylate crosslinking molecule. Exposure to water plasticized the highly crosslinked materials to the degree that the yield point and elastic modulus were effectively lowered. Most of the tested properties were unaffected by differences in functionality except resistance to toothbrush abrasion, which was enhanced for polymers derived from high functionality monomers. The urethane-based polymers sorbed substantially more water than the aromatic-based materials, which presumably resulted in lower values for surface hardness. However, the urethane resins were very tough, and excellent resistance to toothbrush abrasion was observed. Property differences caused by differences in activation mode were small, although the visible light materials did sorb more water.     

Effects of fatty acid oxidation on glucose utilization by isolated hepatocytes

We have studied the inhibitory action of long- and short-chain fatty acids on hepatic glucose utilization in hepatocytes isolated from fasted rats. The rates of hepatic glucose phosphorylation and glycolysis were determined from the tritiated products of [2-3H] and [6-3H]glucose metabolism, respectively. The difference between these was taken as an estimate of the 'cycling' between glucose and glucose-6-phosphate. In the presence of 40 mM glucose this cycling was estimated at 0.68 mumol/min/g wet wt. Glucose phosphorylation was unaffected during palmitate and hexanoate oxidation to ketone bodies but glycolysis was inhibited. The rate of glucose cycling was increased during this phase to 1.25 mumol/min/g. Following the complete metabolism of the fatty acids, glycolysis was reinstated and cycling rates returned to control levels. Hepatic glucose cycling appears to be an important component of the glucose/fatty acid cycle.     

Review: Modified Atmosphere Packaging and its effects on the microbiological quality and safety of produce

Modified Atmosphere Packaging and related technologies are increasingly used to extend shelf-life of fresh produce. This paper reviews the effect of such technology on the spoilage microbiological flora and food-borne pathogens which may be present in produce and also on the organoleptic properties of the product.     

Radiation demineralised bone enhanced osteoinductive capacity after transplantation

Using a mediating alkyne gas during the radiation treatment prevents the degradation of natural and synthetic polysaccharides and proteins. The product has higher viscosity and is more elastic than the original material and, therefore, gives enhanced functionality. Protein, within demineralised bone, too can be modified to give enhanced osteoinductive capacity after transplantation. Thus new functionalities can be achieved from the new products produced in food and medical products.