Stochastic collocation-based nonlinear analysis of concrete bridges with uncertain parameters

This paper focuses on the stochastic response of concrete bridges considering uncertainty in bearing and abutment stiffness. A multi-span simply supported bridge with concrete girders is selected. A 3D-dimensional model is prepared, and nonlinear response history analyses are performed. For the numerical dynamic simulation, the non-sampling stochastic method based on generalized polynomial chaos (gPC) expansion is utilised. The uncertain parameters include the vertical and shear stiffness of bearings and the lateral stiffness of abutments are presented by the truncated gPC expansions. Furthermore, the system response such as base shear, acceleration, velocity and displacement in different columns is presented by gPC expansion with unknown deterministic coefficients. The stochastic Galerkin projection is employed to calculate a set of deterministic equations. A non-intrusive solution, as a set of collocation points, determines the unknown gPC coefficients of the system response and the results are compared with Monte Carlo simulations. The key advantage of spectral discretization is the combination of the mentioned method with the spatial discretization, e.g. finite element model. This study also emphasises the accuracy in results and time efficiency of the proposed non-sampling method for uncertainty quantification of stochastic systems comparing to sampling procedure (e.g. Monte Carlo simulation).     

Evaluation of dynamic modulus measurement for C/C-SiC composites at different temperatures

The determination of elastic properties at application temperature is fundamental for the design of fibre reinforced ceramic composite components. An attractive method to characterize the flexural modulus at room and high temperature under specific atmosphere is the nondestructive Resonant Frequency Damping Analysis (RFDA). The objective of this paper was to evaluate and validate the modulus measurement via RFDA for orthotropic C/C-SiC composites at the application temperature. At room temperature flexural moduli of C/C-SiC with 0/90° reinforcement were measured under quasi-static 4-point bending loads and compared with dynamic moduli measured via RFDA longitudinally to fibre direction. The dynamic modulus of C/C-SiC was then measured via RFDA up to 1250°C under flowing inert gas and showed an increase with temperature which fitted with literature values. The measured fundamental frequencies were finally compared to those resulting from numerical modal analyses. Dynamic and quasi-static flexural moduli are comparable and the numerical analyses proved that bending modes are correctly modeled by means of dynamic modulus measured via RFDA. The nondestructive RFDA as well as the numerical modeling approach are suitable for evaluation of C/C-SiC and may be transferred to other fibre reinforced ceramic composite materials.     

Comparative performance of carbon nanotube and nanoclay on thermal properties and flammability behavior of amorphous polyamide/SEBS blend

Multiwall carbon nanotubes (CNT) or montmorillonite clay (MMT-30B) were added to a poly(hexamethylene isophthalamide-co-terephthalamine) (an amorphous polyamide - aPA) and styrene-ethylene/butylene-styrene graphitized with maleic anhydride (SEBS) blend, in different concentrations, in order to investigate the morphology, thermal properties and flammability behavior. Different nanoparticle localizations in the phase blend were observed through transmission electronic microscopy. CNT nanoparticles are localized in SEBS phase, and MMT-30B nanoparticles in aPA phase. No significant changes were observed on transition temperatures and thermal stability with both nanoparticle additions. However, a slight increase on storage modulus for clay nanocomposites and a slight reduction for carbon nanotube nanocomposites were observed, due to their different phase localizations. Regarding flammability, CNT nanocomposites showed better performance as a flame retardant when compared to samples with MMT-30B. Although the MMT-30B nanocomposites could not be classified according to the UL-94 criteria, no dripped flaming particles were observed, due to the a char barrier formation on the polymer surface. The CNT nanocomposites were classified according to the UL-94 criteria as V-2. The CNT's selective localization on the SEBS phase decreases its heat-release rate, but no interconnected network structure was formed in the matrix to suppress the dripping flaming particles.     

Sintering behavior,microstructure and thermoelectric properties of calcium cobaltite thick films for transversal thermoelectric multilayer generators

The sintering behavior and the thermoelectric performance of Ca₃Co₄O₉ multilayer laminates were studied, and a multilayer thermoelectric generator was fabricated. Compacts and multilayer samples with anisotropic microstructure and residual porosity were obtained after conventional sintering at 920 °C, whereas dense and isotropic multilayer samples were prepared by firing at 1200 °C and reoxidation at 900 °C. A hot-pressed sample has a dense and anisotropic microstructure. Samples sintered at 920 °C exhibit low electrical conductivity due to the low density, whereas the Seebeck coefficient is not sensitive to preparation conditions. However, thermal conductivity of multilayers is very low, and, hence acceptable ZT values are obtained. A transversal multilayer thermoelectric generator (TMLTEG) was fabricated by stacking layers of Ca₃Co₄O₉ green tapes, AgPd conductor printing, and co-firing at 920 °C. The TMLTEG has a power output of 3 mW at ΔT = 200 K in the temperature interval of 25 °C to 300 °C.     

Tunable colors and conductivity by electroless growth of Cu/Cu2O particles on sol-gel modified cellulose

Nano Research - Development of colored surfaces by formation of nano-structured aggregates is a widely used strategy in nature to color lightweight structures (e.g. butterflies) without the use of...     

Lignin from Annual Plants as Raw Material Source for Flavors and Basic Chemicals

The enzymatic conversion of lignins, possibly in combination with electrochemical oxidation, makes aromatics such as syringol, guaiacol, vanillin and catechol available in the qualities required by the fragrance industry. The lignins were obtained by soda digestion from wheat straw and Miscanthus, characterized and then converted with laccases. The overall yield amounted up to 9 wt % with a product spectrum confined to four substances. Catechol was the major product, with a fraction of ≈75 %. It can easily be isolated by extraction with acetone.     

Survey of air pollution in Cotonou, Benin--air monitoring and biomarkers

Exposure to genotoxic compounds present in ambient air has been studied in Cotonou, Benin, a city where two-stroke motorbikes are the major form of transportation and gasoline quality is poor. Personal monitoring and biomarkers were used to assess the exposure. Non-smoking taxi-moto drivers (city) and village residents were the study subjects. Benzene exposure was significantly higher in the city, as compared to the village (76.0+/-26.8 microg/m(3) versus 3.4+/-3.0, p=0.0004). Urinary excretion of benzene and S-phenylmercapturic acid (S-PMA) were also highest in subjects living in the city, whereas 1-hydroxypyrene was not different. The level of total polycyclic aromatic hydrocarbons (PAHs), associated with particles, ranged from 76.21 to 103.23 in Cotonou versus 1.55 ng/m(3) for the village. Determination of DNA damage in lymphocytes showed that subjects from the city had elevated number of lesions compared to subjects in the village in terms of bulky DNA adducts, 8-hydroxy-2'-deoxyguanosine and 5-methylcytosine, whereas DNA fragmentations analysed by alkaline gel electrophoresis was not different between the subjects. In conclusion, this study shows that air pollution is pronounced in Cotonou, Bénin and is associated with elevated levels of DNA damage in residents of the city compared to people living in a non-polluted rural village.