Detection of Multiple Blockages in Parallelized Microreactors

In a plant consisting of parallelized microreactors (MRs), the product quality is lowered because of a lack of flow uniformity among them when blockage occurs. It is not practical to install sensors in every MR from the viewpoint of cost when detecting the blocked MRs. In the previous study, the multiple blockage detection (MBD) method using a small number of sensors was proposed, but its performance became low when the number of sensors decreased. Here, the conventional algorithm for MBD is improved by considering the process behavior on blockage occurrence, and the effectiveness of the improved algorithm is demonstrated through a numerical case study. The effects of flow distributor types and sensor types on the MBD performance are numerically investigated.     

Phase fluctuations of cross-polarized signals at 4 GHz in fine weather on earth-space paths

On an earthspace propagation path with the low elevation angle of 10 deg, the phase between co- and crosspolar signals occasionally showed rapid and irregular fluctuations during fine weather. These fluctuations were generally significant during the daytime, and were strongly in phase with the occurrence of the copolar amplitude scintillations. This could be attributed to the combined effects of the crosspolar phase pattern of the receiving antenna and small fluctuations of the angle of arrival of the radiowaves.     

Formation and Characterization of Ce3ZrO8 Prepared by the Hydrazine Method

A compound denoted as (Ce_0.75Zr_0.25)O₂ (Ce, ZrO₈) is formed near room temperature from cerium and zirconium nitrates using hydrazine monohydrate. It has a cubic unit cell with a = 0.5342 nm. Characterization of powders heated to various temperatures at 10°C/min demonstrates that the specific surface area does not decrease below 20 mVg until >1000°C.     

Extensions of polyacrylic acid ammonium salts in the adsorption layer to fluidize alumina slurries

An average shell volume occupied in the adsorption layer on alumina by a polyacrylic acid ammonium salts molecule (PAA) defined as the average area occupied by an adsorbed PAA on alumina multiplied by the average thickness of the water layer at the limit of thickening, has been calculated from the adsorbed amount of PAA and from the flow points of alumina in the presence of PAA of different molecular weights. A steric effect of the PAA dispersant on the dispersion of alumina resulted in a flow with no yield stress. This was due to the change of the extension of PAA in the adsorption shell from a sphere to an ellipsoid with a long axis which exceeded the effective distance that the van der Waals attraction force reaches at a molecular weight for the PAA of between 10 000–20 000.     

Hydroliquefaction of low-sulfur coals using iron carbonyl complexes—Sulfur as catalysts

Hydroliquefaction of low-sulfur Australian coals (Wandoan and Yallourn) was studied using iron carbonyl complexes as catalyst. The addition of Fe(CO)₅ (2.8 wt% Fe of coal) increased coal conversion from 48.6 to 85.2% for Wandoan coal, and from 36.7 to 69.7% for Yallourn coal in 1-methylnaphthalene at 425°C under an initial hydrogen pressure of 50 kg cm^?2. When molecular sulfur was added to iron carbonyls (Fe(CO)₅, Fe₂(CO)₉ and Fe₃(CO)₁₂), higher coal converions ( > 92%) and higher oil yields (>46%) were obtained, along with an increase in the amount of hydrogen transferred to coal from the gas phase (0.2 to 2.8%, d.a.f. coal basis). In the liquefaction studies using a hydrogen donor solvent, tetralin, Fe(CO)₅S catalyst increased the amount of hydrogen absorbed from the gaseous phase and decreased the amount of naphthalene dehydrogenated from tetralin. The direct hydrogen transfer reaction from molecular hydrogen to coal fragment radicals seems to be a major reaction pathway. Organic sulfur compounds, dimethyldisulfide and benzothiophene, and inorganic FeS₂ and NiS were found to be good sulfur sources to Fe(CO)₅. From X-ray diffraction analyses of liquefaction residues, it is concluded that Fe(CO)₅ was converted into pyrrhotite (Fe_1?xS) when sulfur was present, but into Fe₃O₄ in the absence of sulfur.     

Effects of partial recrystallization on high-cycle fatigue deformation and crack generation of a nitrogen-strengthened 32Mn-7Cr austenitic steel at liquid-nitrogen temperature

To achieve higher fatigue resistance against subsurface crack generation, both the refinement of grain structure and the introduction of mobile dislocations on various slip systems have been shown to be effective in the 32Mn-7Cr austenitic steel. A novel treatment which consisted of cold grooved rolling and partial recrystallization was introduced to modify the microstructure. High-cycle fatigue properties and fatigue-crack generation were investigated for both the solution-treated (ST) and the partially recrystallized (PR) materials at 77 K. The PR material displayed higher fatigue strength than the ST material, especially in the high-cycle regime. No subsurface crack generation was detected for the PR material; however, it appeared in the lower peak stress and/or in the longer-life range for the ST material. Intergranular facets formed a subsurface crack initiation site in the ST material. Since the dislocation structure that developed in the fatigued PR material assisted homogeneous and multidirectional plastic deformation, the localized deformation and/or the stress concentration at the grain boundaries by coplanar arrays were believed to be relieved. Therefore, intergranular cracking due to incompatibility at a grain boundary may disappear.     

Present status and future prospects of PV activities in Japan

The photovoltaic (PV) power systems in Japan made great strides in the past decade. The PV industry in the 1990s greatly depended on the research projects and dissemination programs carried out by the Ministry of International Trade and Industry. However, the industrial structure for full-scale deployment of the PV system is currently being established by the manufacturers’ continuous efforts to reduce the PV system cost and the government’s consecutive supports to create the initial market. It is expected that the synergetic effect of the cost reduction and incentives for introduction will activate the PV industry and its market more and more toward achieving 5000 MW of the capacity in FY 2010.     

Relation between microstructure, properties and spark plasma sintering (SPS) parameters of pure ultrafine WC powder

A combined experimental/numerical methodology is developed to fully consolidate pure ultrafine WC powder under a current-control mode. Three applied currents, 1900, 2100 and 2700 A, and a constant pressure of 20 MPa were employed as process conditions. The developed spark plasma sintering (SPS) finite-element model includes a moving-mesh technique to account for the contact resistance change due to sintering shrinkage and punch sliding. The effects of the heating rate on the microstructure and hardness were investigated in detail along the sample radius from both experimental and modeling points of view. The maximum hardness (2700 HV10) was achieved for a current of 1900 A at the core sample, while the maximum densification was achieved for 2100 and 2700 A. A direct relationship between the compact microstructure and both the sintering temperature and the heating rate was established.     

Premixed flame propagating into a narrow channel at a high speed, part 2: Transient behavior of the properties of the flowing gas inside the channel

The behavior of a premixed flame propagating from a chamber into a narrow channel at a high speed was examined using high speed and instantaneous schlieren photography, ion current measurement with electrostatic probes, and temperature measurement with an optical method. From detailed measurements of flames passing through the channel, flame extinguishment in the channel, no matter whether transient or not, was found to occur due to quenching of the reacting gas by rapid turbulent mixing with cold fresh mixture at the downstream of the contraction region and by heat transfer to the cold channel walls. Extinguishment must occur when these heat losses exceed the heat released by the chemical reaction of the flowing mixture.