Novel Green Corrosion Inhibitor for Mild Steel in Sulfuric Acid

Protection of Metals and Physical Chemistry of Surfaces - Salix leaves water extract was studied for the corrosion inhibition of mild steel in H2SO4 at different temperatures. Energy dispersive...     

Synthesis,structural, linear and nonlinear optical properties of chromium doped SnO2 thin films

The present work concentrates on some physical investigation of the undoped and Cr doped SnO₂ thin films deposited onto precleaned glass substrates by the spray pyrolysis system. The physical properties of the undoped and Cr doped SnO₂ thin films were investigated by the X-ray diffraction (XRD), atomic force electron microscope (AFM), field emission scanning electron microscope (FESEM), four-probe method and double beam spectrophotometer. The undoped and Cr doped SnO₂ films display a polycrystalline nature with orthorhombic crystal structure. The linear optical constants energy gap E_g, refractive index n, absorption coefficient α, static refractive index n_o, oscillation energy E_o, dispersion energy E_d and the Urbach energy of the undoped and Cr doped SnO₂ thin films were evaluated. The investigated films exhibit a direct energy gap and their values decrease with the increasing of Cr doping content while the Urbach energy follows a reverse behavior. On the other hand, the nonlinear optical constants (third-order nonlinear susceptibility ${\mathit{\chi }}^{(3)}$ and nonlinear refractive index n₂) have been increased with increasing the Cr doping content. Finally, it has been found that the sheet resistance and conductivity of the synthesized thin films were enhanced by increasing the Cr doping content. The 5?wt% Cr doped SnO₂ thin film has a high value of the figure of merit among other films.     

Polylactide‐perylene derivative for blue biodegradable organic light‐emitting diodes

In this work we demonstrate, for the first time, the use of polylactic acid (PLA) as a biodegradable host matrix for the construction of the active emissive layer of organic light‐emitting diode (OLED) devices for potential use in bioelectronics. In this preliminary study, we report a robust synthesis of two fluorescent PLA derivatives, pyrene‐PLA ( AH10 ) and perylene‐PLA ( AH11 ). These materials were prepared by the ring opening polymerisation of l ‐lactide with hydroxyalkyl‐pyrene and hydroxyalkyl‐perylene derivatives using 1,8‐diazabicyclo[5.4.0]undec‐7‐ene as catalyst. OLEDs were fabricated from these materials using a simple device architecture involving a solution‐processed single‐emitting layer in the configuration ITO/PEDOT:PSS/PVK:OXD‐7 (35%): AH10 or AH11 (20%)/TPBi/LiF/Al (ITO, indium tin oxide; PEDOT:PSS, poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonic acid); PVK, poly(vinylcarbazole); OXD‐7, (1,3‐phenylene)‐bis‐[5‐(4‐tert‐butylphenyl)‐1,3,4‐oxadiazole]; TPBi, 2,2′,2″‐(1,3,5‐benzenetriyl)tris(1‐phenyl‐1H‐benzimidazole)). The turn‐on voltage for the perylene OLED at 10 cd m^–2 was around 6 V with a maximum brightness of 1200 cd m^–2 at 13 V. The corresponding external quantum efficiency and device current efficiency were 1.5% and 2.8 cd A^–1 respectively. In summary, this study provides proof of principle that OLEDs can be constructed from PLA, a readily available and renewable bio‐source. © 2020 The Authors. Polymer International published by John Wiley & Sons Ltd on behalf of Society of Industrial Chemistry.     

Interval analysis of mode shapes to identify damage in beam structures

Various damage detection methods have been proposed by several researchers in the past few decades. Amongst them, the efficiency of mode shapes in detecting damage has been demonstrated by many researchers when further processed. In most cases, the processing involves expansion or reduction of the mode shape data. However, vital information that are damage-prints are often lost during processing of the mode shape data. In addition, most of these processes involve long and complex computation, thus, leading to inaccurate damage identification. In this study, a simple and fast damage identification technique is proposed to identify damage in beam structures. Interval analysis is applied to the mode shapes of a beam structure in the damaged and undamaged states. The interval situations of each of the beam's segment via mode shape are derived to obtain the upper and lower bounds and the derived bounds are compared. To establish a relationship for identify the damaged point, a possibility of damage existence is defined for each segment of the beam structure. The mode shape increment is defined as the increase in the mode shape value. Furthermore, a damage measure index that provide enhance damage information is obtained as the product of the possibility of damage existence and mode shape increment. A numerical model of a simply supported steel beam is applied to demonstrate this method by imposing damage through thickness reduction of elements in segments. In addition, a parametric analysis is carried out to evaluate noise effect by considering varying damage severities and different noise levels. The results showed that this method is simple and provides considerable accurate results.     

High‐Purity Tocored Improves the Stability of Stripped Corn Oil Under Accelerated Conditions

γ‐Tocopherol‐5,6‐quinone (tocored) is of importance among the γ‐tocopherol (γ‐T) oxidant products and found in corn germ oil. Investigation on tocored is impeded in part by the difficulty to access high purity tocored. In this present study, high‐purity tocored is successfully prepared, and its antioxidant activity, together with γ‐T and TBHQ (positive control) in increasing concentrations in stripped corn germ oil is evaluated by Rancimat and Schaal oven tests. The stabilization factor in the Rancimat tests increases significantly (p < 0.05) along with an increase in the levels of antioxidants. Furthermore, tocored exhibits higher stabilization than γ‐T in the Schaal oven tests, although its efficacy gradually increases up to 100 mg kg^–1 and decreases significantly at higher levels (from 100 to 500 mg kg^–1), drawn from the comprehensive parameter A (considering both efficiency and strength) changes (5.06–11.21). In addition, the curves illustrating the residual contents of tocored and γ‐T run in different ways when the four levels are taken into consideration, further bearing the above results. Tocored tends to be a potent natural antioxidant for edible corn germ oil preservation. Practical Application: The present work provides more clear procedures for high‐purity tocored synthesis. Furthermore, tocored may be a potential natural antioxidant that is especially suitable for lipid base food substrates. The results of the present work contribute to the deeper understanding of the antioxidant activity of γ‐tocopherol. The antioxidant activity of tocored is higher than γ‐tocopherol in Schaal oven test. Tocored is a bright orange‐red substance that affects the appearance of the edible oil. Meanwhile, γ‐tocopherol is well known for its valuable health benefits, and appropriate measures should be adopted to store oils (corn oil, soybean oil, and so on) rich in γ‐tocopherol to control transformation in order to keep stability optimal. To some degree, the practical applications of the present results are also related to the processing and storage of edible oils.     

Boosting the activity of FeOOH via integration of ZIF-12 and graphene to efficiently catalyze the oxygen evolution reaction

Transition metal oxyhydroxides have been used as promising electrocatalysts for water splitting however, their catalytic activity is restricted due to low surface area and poor conductivity. Herein, we report novel composite FeOOH@ZIF-12/graphene composite as electrocatalyst for water oxidation, whereby ZIF-12 provide extra surface for the FeOOH dispersion whilst graphene act as excellent electron mediator. The composite shows a low overpotential value of 291 mV to attain a current density of 10 mA cm^?2 and a low Tafel slope value of 78 mV dec^?1. The catalyst offers a maximum current density of 101 mA cm^?2, while it gives a turnover frequency (TOF) value of 0.031 s^?1 at an overpotential of 291 mV only. The excellent activity and remarkable stability of composite is attributed to highly conductive and porous support.     

A new application of giant reed waste material for ammonium removal

Excess nitrogen is one of the main causes of eutrophication in water bodies. In this study, the undesirable agricultural lignocellulosic material giant reed was used to remove ammonium ions from aqueous solutions. Batch experiments were conducted to investigate the effect of various parameters such as contact time, initial ammonium concentration, adsorbent dosage, pH, particle size, agitation rate and phosphate coexisting during the ammonium adsorption process. The ammonium sorption capacity of fibrous giant reed (FGR) at equilibrium was 12.49?mg?N/g with a maximum removal efficiency of 76% observed within 30?min at pH range of 6.5–9.5. Results revealed that the Freundlich isotherm model fitted better with the sorption process than the Langmuir model, and the adsorption process was well described by pseudo-second-order kinetic model. FT-IR analyses indicated that complexation and ion exchange could be the main mechanisms for the ammonium removal by FGR. Results revealed that FGR has a sorption capacity comparable to that of other natural sorbents with the advantage of greater availability with no cost.     

Ultra low loss (Mg1 − xCax)2SiO4 dielectric ceramics (x = 0 to 0.15) for millimeter wave applications

(Mg_{1 − x}Ca_x)₂SiO₄ dense ceramics (x ≥ 0.15) were prepared, and their microwave dielectric characteristics were investigated together with the structure evolution. The sintering temperature for Mg₂SiO₄ ceramics was reduced significantly with Ca²⁺substitution. (Mg_{1 − x}Ca_x)₂SiO₄ ceramics exhibited a small increase in dielectric constant (ε_r) correlated with increased crystallite size, and ultra-high quality factor Qf value was achieved throughout the compositional range. Temperature coefficient of resonant frequency (τ_f) was considerably tuned from −70 ppm/°C to −33 ppm/°C, and this improvement was deeply linked with the decreased bond valance. At x = 0.075, (Mg_{1 − x}Ca_x)₂SiO₄ ceramics exhibited the best combination of microwave dielectric characteristics: ε_r = 7.2, Qf = 199,800 GHz at 26 GHz, τ_f = −33 ppm/°C. The present ceramics could be expected as promising candidate of dielectric materials for millimeter wave applications.     

Core–shell structured Cu@Pt nanoparticles as effective electrocatalyst for ethanol oxidation in alkaline medium

Core–shell nanoparticles of Cu@Pt/C electrocatalysts were synthesized using various Pt:Cu atomic ratios with NaBH₄ as a reducing agent. The crystal structure and surface morphology were studied using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The incorporation of copper in Cu@Pt/C electrocatalysts was found to shift all Pt diffraction planes in the negative direction with expanding the crystal lattice dimensions. The electrocatalytic activity of various Cu@Pt/C electrocatalysts was investigated using cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy. Cu@Pt/C electrocatalysts containing Pt:Cu atomic ratios of 1:0.5 and 1:2 showed an enhanced electrochemical performance for ethanol oxidation when related to Pt/C.