Localized corrosion of (lean) duplex stainless steels in immersion units of urban wastewater treatment plants

With lower alloying cost and higher mechanical properties, lean duplex stainless steels can be an alternative to the more commonly used austenitic stainless steels. However, these alloys are still not the preferred choice, probably due to a lack of field experience. A study was thus initiated in view of defining the limits of use of selected (lean) duplexes for urban wastewater treatment units. The present paper shows the localized corrosion performance of selected lean duplexes in chloride contaminated solutions. The results are compared with austenitic S30403 and S31603 and with the more standard duplexes S82441 and S32205. The effect of welding was also investigated. Exposures in field municipal wastewater plants were conducted for 1 year in low and high chloride content units. The results show that lean duplexes S32101 and S32202 can be used as alternatives to S30403 and S31603 in low chloride electrolytes. At 500 ppm of chloride content, duplex stainless steel S32304 showed better corrosion resistance than S30403 and S31603. For higher chloride contents (1000 ppm and above) the standard duplexes S82441 and S32205 shall be preferred.     

Potential influence of microorganisms on the corrosion of carbon steel in the French high- and intermediate-level long-lived radioactive waste disposal context

In the context of the high-level radioactive waste disposal CIGEO, the corrosion rate due to microbially influenced corrosion (MIC) has to be evaluated. In France, it is envisaged to dispose of high- and intermediate-level long-lived radioactive waste at a depth of 500 m in a deep geological disposal, drilled in the Callovo-Oxfordian claystone (Cox) formation. To do so, a carbon steel casing will be inserted inside disposal cells, which are horizontal tunnels drilled in the Cox. A specific cement grout will be injected between the carbon steel casing and the claystone. A study was conducted to evaluate the possibility of MIC on carbon steel in the foreseeable high radioactive waste disposal. The corrosiveness of various environments was investigated at 50°C and 80°C with or without microorganisms enriched from samples of Andra's underground research laboratory. The monitoring of corrosion during the experiments was ensured using gravimetric method and real-time corrosion monitoring using sensors based on the measurements of the electrical resistance. The corrosion data were completed with microbiological analyses including cultural and molecular characterizations.     

Corrosion of hot-dip-galvanised steel and zinc alloy-coated steel in ammonia and ammonium chloride

There are many potential causes of corrosion in animal buildings. Animals exhale large quantities of moisture into the air creating high relative humidity in the building if the moisture is not properly vented. High humidity increases the potential for condensation. In addition, ammonia may be found in large quantities in animal buildings. Ammonia is released from manure and urine. In addition, ammonium chloride is used as a nitrogen source in fertilisers. In this study, the atmospheric corrosion of hot-dip-galvanised steel and zinc alloy-coated steel such as zinc–aluminium and zinc–aluminium–magnesium has been studied in atmospheres containing different levels of ammonia. Investigations have also been conducted at different levels of ammonium chloride. The results are discussed in view of the mechanisms of corrosion of zinc and zinc alloy-coated steel in ammonia and ammonium chloride-containing environments.     

Cyanogenic,carotenoids and protein composition in leaves and roots across seven diverse population found in the world cassava germplasm collection at CIAT,Colombia

The objective of this study was to characterise the nutritional potential of leaves and identify a diversity centre with low cyanide and high nutrient content among 178 Latin American cassava genotypes. This field-based collection represents the seven diversity centres, held at The International Center for Tropical Agriculture (CIAT Palmira, Colombia) by the Cassava Program. The cyanide, all-trans-β-carotene and lutein concentrations in cassava leaves ranged from 346 to 7484 ppm dry basis (db), from 174–547 μg g⁻¹ db and 15–181 μg g⁻¹ db, respectively. Cassava leaves also showed significant levels of essential amino acids leucine, lysine, phenylalanine, valine and threonine, and average total protein content of 26.24 g 100 g⁻¹ db. Among seven diversity centres, South American rainforest group showed low cyanide and high carotene content in leaves. In addition, VEN77 and PAN51 genotypes stood out for having low cyanide in leaves and roots and high carotene in leaves. This genetic diversity can be used to select high potential progenitors for breeding purposes.     

X-ray microtomography: Application to microstructure analysis of a cementitious material during leaching process

Leaching of cementitious materials leads to an increase in porosity, which has important consequences on transport and mechanical properties. The present study outlines the characterization of microstructural evolution in a mortar subjected to a chemical attack, by means of a powerful non-intrusive experimental method, namely synchrotron X-ray computed microtomography. This innovative method is used to measure the variation of porosity in a leached mortar. Having described the effects of leaching in mortar (influences on microstructure and on mechanical properties), we present the accelerated leaching process and the microtomographic analysis that have been used to monitor it. We then investigate the capacity of this method to quantify the evolution of porosity during the leaching process. The method is validated by comparison of the results obtained with data available in the literature.     

AgNO<Subscript>3</Subscript> spray tests: advantages,weaknesses, and various applications to quantify chloride ingress into concrete. Part 1: Non-steady-state diffusion tests and exposure to natural conditions

Within the framework of the evaluation and the prediction of chloride-induced corrosion risks, simple and rapid AgNO₃ spray tests can be proposed for various issues. This paper forms the first part of a series. In this first part, the Maultzsch procedure (spraying of 0.1-N AgNO₃ solution + K₂CrO₄) as well as the procedure based on the use of a sole AgNO₃ solution have been investigated on a broad range of concretes. These procedures have also been compared to the Collepardi procedure (spraying of 0.1-N AgNO₃ + fluoresceine). The feasibility of these colorimetric techniques on saturated specimens cast in laboratory, after non-steady-state diffusion tests carried out in various conditions, is discussed. In addition, the results obtained from applying such spray tests in field conditions on cores drilled out from various RC test specimens exposed to a marine environment (tidal zone) and to a road and cold environment (freezing-thawing cycles and spraying of deicing salts) are presented. Colorimetric methods have in particular been applied here to the assessment of the average chloride penetration depth and of its evolution versus time (kinetics). Moreover, the detection threshold of these techniques has been investigated in various environments. The possible sources of discrepancy on the results have been analysed.     

Hybrid Approach for Addressing Uncertainty in Risk Assessments

Parameter uncertainty is a major aspect of the model-based estimation of the risk of human exposure to pollutants. The Monte Carlo method, which applies probability theory to address model parameter uncertainty, relies on a statistical representation of available information. In recent years, other uncertainty theories have been proposed as alternative approaches to address model parameter uncertainty in situations where available information is insufficient to identify statistically representative probability distributions, due in particular to data scarcity. The simplest such theory is possibility theory, which uses so-called fuzzy numbers to represent model parameter uncertainty. In practice, it may occur that certain model parameters can be reasonably represented by probability distributions, because there are sufficient data available to substantiate such distributions by statistical analysis, while others are better represented by fuzzy numbers (due to data scarcity). The question then arises as to how these two modes of representation of model parameter uncertainty can be combined for the purpose of estimating the risk of exposure. This paper proposes an approach (termed a hybrid approach) which combines Monte Carlo random sampling of probability distribution functions with fuzzy calculus. The approach is applied to a real case of estimation of human exposure, via vegetable consumption, to cadmium present in the surficial soils of an industrial site located in the north of France. The application illustrates the potential of the proposed approach, which allows the uncertainty affecting model parameters to be represented in a way that is consistent with the information at hand. Also, because the hybrid approach takes advantage of the “rich” information provided by probability distributions, while retaining the conservative character of fuzzy calculus, it is believed to hold value in terms of a “reasonable” application of the precautionary principle.     

Modeling of Moisture Behavior of Wood Planks in Nonvented Flat Roofs

A computer model was extended and adapted to simulate the hygrothermal behavior of building envelope-wood components. The model was used to predict moisture movement in wood planks forming the decks of nonvented flat roofs insulated with cellulose. The gradient of water potential was considered as the driving force for moisture movement in wood. The model required the determination of convective heat- and mass-transfer coefficients, the sorption curves, the effective water conductivity for different wood species, and the hygrothermal conditions within the assembly to characterize the mass-conservation equation. Once these parameters were integrated in the computer model, this approach was then validated by carrying a simulation of the drying process of wood planks using experimental data from a large-scale test.     

DSC and DMTA characterization of ternary blends

The phase behavior of ternary blends made of poly(epichlorohydrin) (PECH), poly(vinyl acetate) (PVAc) and poly(methyl methacrylate) (PMMA) has been investigated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). DMTA measurements have been shown to be more sensitive than DSC for the detection of a second phase, for the determination of the composition of each phase, and the distribution of PECH in each of them. About 70% PECH was required to obtain a single narrow T_g in the ternary system, which suggests a single homogeneous phase in the limit of sensitivity of DMTA. This study also emphasizes the importance of the composition of the immiscible polymer pair (i.e. the PVAc/PMMA pair in the PECH/PVAc/PMMA system), in addition to the thermodynamic interaction parameters, for controling the phase behavior of ternary systems.