Liquid Marble Patchwork on Super-Repellent Surface

Liquid marble (LM) is a droplet that is wrapped by hydrophobic solid particles, which behave as a non-wetting soft solid. Based on these properties, LM can be applied in fluidics and soft device applications. A wide variety of functional particles have been synthesized to form functional LMs. However, the formation of multifunctional LMs by integrating several types of functional particles is challenging. Here, a general strategy for the flexible patterning of functional particles on droplet surfaces in a patchwork-like design is reported. It is shown that LMs can switch their macroscopic behavior between a stable and active state on super-repellent surfaces in situ by jamming/unjamming the surface particles. Active LMs hydrostatically coalesce to form a self-sorted particle pattern on the droplet surface. With the support of LM handling robotics, on-demand cyclic activation–manipulation–coalescence–stabilization protocols by LMs with different sizes and particle types result in the reliable design of multi-faced LMs. Based on this concept, a single bi-functional LM is designed from two mono-functional LMs as an advanced droplet carrier.     

Influence of LiBO2 addition on the microstructure and lithium-ion conductivity of Li1+xAlxTi2−x(PO4)3(x = 0.3) ceramic electrolyte

Concerning the safety problems of conventional Li-ion batteries with liquid electrolytes, it is crucial to develop reliable solid-state electrolytes with high ionic conductivity. Li_1+xAl_xTi_2?x(PO₄)₃ (LATP, x = 0.3) is regarded as one of the most promising solid electrolytes due to its high ionic conductivity and excellent chemical stability to humidity.Herein, a new strategy is proposed for improving the sintering behavior and enhancing the ionic conductivity of LATP by using LiBO₂ as the sintering aid via liquid phase sintering. The as-prepared sample LATP with homogeneous microstructure and high relative density of 97.1% was successfully synthesized, yielding high total ionic conductivity of 3.5 × 10^?4 S cm^?1 and low activation energy of 0.39 eV at room temperature. It was found that the addition of LiBO₂ could effectively enhance the densification and increase the ionic conductivity of LATP electrolyte, proving an effective way to synthesis LATP ceramics by a simple and reliable route.     

Fragility analysis for ballistic design

Effective structural design to resist ballistic effects such as small arms or fragmenting weapons has been a goal since weapons were developed. Approaches currently in use for ballistic design are predominantly deterministic and allow designers to decide what wall thickness should be used to stop a prescribed projectile impacting at a predefined velocity. The research presented in this paper provides a framework for conducting reliability analysis of structures subjected to bullet and fragment demands. Thus, pseudo-fragility curves are developed for the limit states related to spall and perforation of wall panels, residual velocities of bullets and fragments, and injury to personnel. The pseudo-fragility analysis provides engineers and owners with a tool to quickly assess the reliability of a wall system subjected to high velocity, low mass projectiles. In particular, the proposed analysis method allows designers and owners to determine the probability of spall and perforation, residual velocity, and injury as a function of wall thickness or threat standoff distance.

Abbreviations: Cumulative distribution function (CDF): Gives the probability that a stochastic variable ‘X’, with a proper probability density function, is equal to or less than a value (x). Coefficient of variation (COV): The quotient of the standard deviation and the mean     

Column-mode phosphate removal by a novel highly selective adsorbent

A phosphoric acid resin RGP was immobilized with zirconium(IV) (Zr(IV)) to investigate its applicability in phosphate removal. When loaded with Zr(IV), RGP was changed into an effective ligand exchanger with phosphate sorption capacity of 0.345 mmol/ml. Little metal leakage was observed. Breakthrough of phosphate sorption depended on solution acidity and phosphate concentration. An increase of solution pH greatly suppressed phosphate removal, but even at pH 8.21, about 56% of the added phosphate (2.8mM) in the feed solution could still be sorbed. Electrolytes in the aqueous solution did not interfere with phosphate sorption; on the contrary, an enhancement effect was observed. Due to the high sorption capacity of Zr(IV)-loaded RGP, low concentration of phosphate can be removed at high flow rate (100 h(-1) in space velocity). The sorbed phosphate on the Zr(IV)-loaded RGP could be quantitatively eluted with 0.5M sodium hydroxide solution. The Zr(IV)-loaded RGP is a promising ligand exchanger for treating wastewater containing trace amounts of inorganic phosphate.     

Barosensitivity in Saccharomyces cerevisiae is Closely Associated with a Deletion of the COX1 Gene

High hydrostatic pressure causes physical stress to microorganisms; therefore, this technology may be applied to food pasteurization without introducing the unfavorable effects of thermal denaturation. However, its application is limited to high‐value foods because the treatment requires a robust steel vessel and expensive pressurization equipment. To reduce these costs, we studied the pasteurization of Saccharomyces cerevisiae using relatively moderate high‐pressure levels. A mutant strain isolated by ultraviolet mutagenesis showed significant loss of viability under high‐pressure conditions. Gene expression analysis of the mutant strain revealed that it incurred a deletion of the COX1 gene. Our results suggest that the pressure‐sensitivity can readily be introduced into industrial/food microorganisms by complementing a COX1 deleted mitochondria.     

Asymmetric Multidimensional Scaling of Brand Switching Among Margarine Brands

Behaviormetrika - Brand switching data among 12 margarine brands were analyzed by the asymmetric multidimensional scaling based on the singular value decomposition. A two-dimensional result was...     

Tensile Properties and Fracture Behavior of Different Carbon Nanotube-Grafted Polyacrylonitrile-Based Carbon Fibers

The tensile properties and fracture behavior of different carbon nanotube (CNT)-grafted polyacrylonitrile-based (T1000GB) single carbon fibers were investigated. Grafting of CNTs was achieved via chemical vapor deposition (CVD). When Fe(C₅H₅)₂ (also applied via CVD) was used as the catalyst, the tensile strength and Weibull modulus of the carbon fibers were improved, possibly due to the growth of dense CNT networks on the carbon fibers, which may have led to a reduction in the number of strength-limiting defects. Separately, at lower concentrations of an Fe(NO₃)₃·9H₂O catalyst in ethanol, which was applied via dipping, the tensile strength of CNT-grafted fibers was nearly identical to that of the as-received fibers, although the Weibull modulus was higher. For higher concentrations of the Fe(NO₃)₃·9H₂O catalyst, however, the tensile strength and the Weibull modulus were lower than those for the as-received material. Although the density of the CNT network increased with the concentration of the Fe(NO₃)₃·9H₂O catalyst in the ethanol solution, heating of the ethanolic Fe(NO₃)₃·9H₂O catalyst solution generated nitric acid (HNO₃) due to decomposition, which damaged the fiber surfaces, resulting in an increase in the number of flaws and consequently a reduction in the tensile strength. Therefore, the tensile strength and Weibull modulus of CNT-grafted carbon fibers vary due to the combination of these effects and as a function of the catalyst concentration.