Synthesis of Janus polyaniline–polyelectrolyte complex membrane via in situ confined polymerization

Polyelectrolyte complex (PEC) membranes prepared from poly(styrene sulfonate) (PSS) and poly(diallyldimethylammonium chloride) (PDADMAC) were modified by crossflow polymerization of aniline (ANI). The PEC membranes were used as separators in a two-compartment setup where ANI monomer and ammonium persulfate (APS) oxidant diffused through the membranes to form polyaniline (PANI). APS and ANI having different distributions throughout the membranes, the reaction led to the asymmetric polymerization of PANI on one face of each PEC membrane thus producing Janus membranes. Due to the excess PANI content, the membrane displayed distinct asymmetric electrical conductivities on each face. Interestingly, very different ANI polymerizations were obtained when nonstoichiometric PEC membranes having different molar ratio of cationic and anionic polyelectrolytes (P⁺:P^? represents PDADMAC:PSS) were used and transport of APS was fastest through the 2:1 PEC when compared to the 1:2 PEC. In all experiments, the polymerization was most intense on the ANI side of the membranes. Also, the influence of NaCl both during PEC fabrication and during polymerization was studied and found to have some effect on the solute permeability. Results showed that a higher content of PANI was formed on PEC membranes having excess P⁺ and with no NaCl added during PEC fabrication. Although X-ray diffraction confirmed the presence of PANI on both sides of each membrane, scanning electron microscopy images demonstrated that both sides of each membrane had different PANI content deposited. Electrical conductivity measurements using a four-point probe setup also showed that the PEC–PANI exhibits asymmetric electrical property on different sides. © 2021 Society of Industrial Chemistry.     

Droplet Entrainment Analysis in a Flash Evaporator with an Image-Based Measurement Technique

Local droplet sizes and volumes of entrained liquid are captured with an image-based measurement technique for comparison with a conventional, integral method for entrainment analysis. Experiments in a forced circulation flash evaporation were performed for different operating conditions and with two different chemical systems. Droplet size and frequency rise with an increase in thermal energy input. The local readings confirm the trends found by the integral measurement method. The modification of the image-based probe enables the detection of small (≈ 10 µm) and at the same time fast droplets under challenging operating conditions, such as vacuum and superheated feed similar to industrial process conditions.     

Exergy analysis of the diesel pre-reforming solid oxide fuel cell system with anode off-gas recycling in the SchIBZ project. Part I: Modeling and validation

Solid oxide fuel cell (SOFC) systems with anode off-gas recirculation (AGR) and diesel pre-reforming are advantageous because they can operate with the current fuel infrastructure. In the SchIBZ-project, the prototype of such a SOFC system for maritime applications has already been commissioned. In this first paper, we model the system devices to conduct an exergy analysis of this real SOFC plant and validate them with experimental values from experiments in laboratory scale. The results of our simulation agree well with the experimental values. The calculations with the validated results may be closer to the real thermodynamic behavior of such system components than previous literature.     

Elastic instabilities,microstructure transformations,and pattern formations in soft materials

Large deformations of soft materials can give rise to the development of various elastic instabilities. The phenomenon is associated with a sudden and dramatic change in structure morphologies. The underlying mechanism is crucial for the formation of complex morphologies in biology. Moreover, the concept of instability-induced pattern transformations is promising for designing novel materials with switchable functions and properties. In this paper, we review the state of the art in elastic instability phenomena in soft materials. We start by considering the classical buckling in beam-based structure lattice designs. Then, we discuss the instability-induced microstructure transformations in soft porous materials, and heterogeneous multiphase and fiber composites. Next, the mechanisms – often involving the post-buckling consideration – leading to the wrinkling and folding, creasing, fringe, and fingering are discussed.     

Biosynthetic Plasticity Enables Production of Fluorinated Aurachins

Enzyme promiscuity has important implications in the field of biocatalysis. In some cases, structural analogues of simple metabolic building blocks can be processed through entire pathways to give natural product derivatives that are not readily accessible by chemical means. In this study, we explored the plasticity of the aurachin biosynthesis pathway with regard to using fluoro- and chloroanthranilic acids, which are not abundant in the bacterial producers of these quinolone antibiotics. The incorporation rates of the tested precursor molecules disclosed a regiopreference for halogen substitution as well as steric limitations of enzymatic substrate tolerance. Three previously undescribed fluorinated aurachin derivatives were produced in preparative amounts by fermentation and structurally characterized. Furthermore, their antibacterial activities were evaluated in comparison to their natural congener aurachin D.     

Measuring Local Crystallization Fouling in a Double-Pipe Heat Exchanger

Abstract

Although fouling is a problem varying in space and time, sizing and assessment of a process apparatus is almost always based on one single integral fouling resistance value. Furthermore, the integral fluid dynamic behavior, e.g. the development of time-dependent pressure drop in a heat exchanger, can be influenced by local constrictions. While it is generally possible to determine the time dependency of the integral fouling behavior, local differences are not taken into consideration at present. Therefore, this paper introduces a metrological, an incremental and a segmental approach to study the local development of crystallization fouling by calcium sulfate in a countercurrent double-pipe heat exchanger. The consecutive approaches allow for thermal, volumetric, gravimetric, and optical fouling investigations, aiming to examine the axial distribution of deposit as well as local differences in the deposit morphology. All methods provided congruent results and local fouling could be described properly. An almost clean surface at the colder end of the heat exchanger and an exponential increase of deposit thickness were observed towards the hot end. Hence, the section near to the hot water inlet turned out to be a key area with regards to increasing fouling mass and structural changes of the layer.     

Enhancing the temperature stability of PLA by compounding strategies

The low thermal stability of polylactid acid (PLA) limits its use for various applications such as microwave‐ready dishes or hot beverage packaging. Furthermore, contained items might be damaged by occurring temperature peaks during transport (e.g., shipping container internal temperature exceeds 80°C) or other usage (e.g., car dashboard heated by sun). The aim of this study was the development of a PLA compound with an operating temperature above 100°C. Therefore, different formulations (e.g., stereocomplex of PLLA and PDLA, cross‐linking of PLA or use of commercial additives) were identified and compounds with varying conditions produced and tested regarding their thermal and mechanical properties. The results showed clearly possible routes for improving the thermal properties of PLA. Using such compounds respectively processing routes and additives helps to overcome one of the most significant problems when using PLA. The higher operating temperature of this biopolymer will lead to a wider field of application and will avoid shipping hazards. POLYM. ENG. SCI., 55:2849–2858, 2015. © 2015 Society of Plastics Engineers     

Adventitial Tertiary Lymphoid Organs as Potential Source of MicroRNA Biomarkers for Abdominal Aortic Aneurysm

Abdominal aortic aneurysm (AAA) is an inflammatory disease associated with marked changes in the cellular composition of the aortic wall. This study aims to identify microRNA (miRNA) expression in aneurysmal inflammatory cells isolated by laser microdissection from human tissue samples. The distribution of inflammatory cells (neutrophils, B and T lymphocytes, mast cells) was evaluated in human AAA biopsies. We observed in half of the samples that adventitial tertiary lymphoid organs (ATLOs) with a thickness from 0.5 to 2 mm were located exclusively in the adventitia. Out of the 850 miRNA that were screened by microarray in isolated ATLOs (n = 2), 164 miRNAs were detected in ATLOs. The three miRNAs (miR-15a-3p, miR-30a-5p and miR-489-3p) with the highest expression levels were chosen and their expression quantified by RT-PCR in isolated ATLOs (n = 4), M1 (n = 2) and M2 macrophages (n = 2) and entire aneurysmal biopsies (n = 3). Except for the miR-30a-5p, a similar modulation was found in ATLOs and the two subtypes of macrophages. The modulated miRNAs were then evaluated in the plasma of AAA patients for their potential as AAA biomarkers. Our data emphasize the potential of miR-15a-3p and miR-30a-5p as biomarkers of AAA but also as triggers of ATLO evolution. Further investigations will be required to evaluate their targets in order to better understand AAA pathophysiology.