Evaluation of the Properties of Si3N4/Si3N4 Joint Brazed Using a Filler Alloy Containing Pd

Si3N4 ceramic was jointed to itself using a filler alloy of Cu76.5Pd8.5Ti15, and the mechanical properties of the jointwere measured and analyzed. By using a filler alloy of Cu76.5Pd8.5Ti15, the SisN4/SisN4 joints were obtained bybrazing at 1373～1473 K f     

Transmission distance of in-line amplifier systems withgroup-velocity-dispersion compensation

Group-velocity dispersion (GVD) compensation in in-line amplifier systems is evaluated from the viewpoint of improving the transmission distance. The nonlinear Schrodinger equation, which simulates signal propagation in optical fibers, is numerically evaluated to clarify the optimum configuration for GVD compensation. It is shown that the optimum amount of GVD compensation is about 100% of the GVD experienced by the transmitted signal. The optimum compensation interval is found to be a function of the bit rate, signal power, and dispersion parameter. For dispersion parameter values ranging from about -0.1 ps/nm/km to -10 ps/nm/km, and an amplifier noise figure of about 6 dB, the optimum compensation configuration can eliminate the GVD from in-line amplifier systems, thus improving transmission distances to those limited by self-phase modulation and higher-order GVD     

Fibre transmission distance determined by eye opening degradation due to selfphase modulation and group-velocity dispersion

Numerical analysis of IM signal propagation in an optical fibre is carried out taking selfphase modulation and group-velocity dispersion into account. The transmission distance yielding a prescribed eye opening penalty, in the normal dispersion region, is shown to be inversely proportional to the square root of the signal power.<>     

Hydrothermal synthesis and in situ surface modification of boehmite nanoparticles in supercritical water

In situ surface modification of boehmite (AlOOH) nanoparticles during hydrothermal synthesis in supercritical water was examined by adding CH₃(CH₂)₄CHO and CH₃(CH₂)₅NH₂ as modifier reagents to the reactants. Changes in surface properties of the nanoparticles by surface modification was observed by FTIR, dispersion in solvents and TEM analyses, which demonstrated that reagents chemically binded onto the surface of the AlOOH nanoparticles. The results of SEM and TEM pictures show that the surface modification affects crystal growth and reduces the particle size and changes the morphology of the particles.     

Detection and modification of confusing color combinations for red‐green dichromats to achieve a color universal design

Color‐vision deficiency is a relatively common genetic condition, which often leads to the obstruction of necessary information in colored images. It is important to minimize such inconvenient effects in communication using colored images from a universal design perspective. The universal design principle stipulates that all environments and products should be usable by all people, regardless of age, physical attributes, and ability. This article proposes a method to detect color combinations in a given image that would confuse color dichromats, and suggests a way in which to modify them to make the image easily distinguishable for both normal and dichromatic observers. Confusing color combinations were detected based on a color‐difference calculation using simulations of how the color would appear to dichromats. The confusing colors were then modified based on the minimization of an evaluation function, which was defined as the sum of the degree of confusion and the degree of color change from the original image. Several colored images obtained by the proposed method were compared with the originals by red–green dichromatic observers who judged them to be clearer, thereby confirming that the proposed method was effective for color rendering for universal design. © 2008 Wiley Periodicals, Inc. Col Res Appl, 33, 203–211, 2008     

Molecular beam epitaxial growth of SrO and CaO with RHEED intensity oscillation

SrO and CaO, related compounds of BSCCO superconductor, are grown onto SrTiO₃(100) substrates with molecular beam epitaxy(MBE) technique. During growth, the specular spots of RHEED patterns show intensity oscillations, indicating two dimensional growth. The periods of oscillations are utilized to calculate the atom fluxes. It is shown that sublimation processes of both Sr and Ca metals in the effusion cells are stable under the growth condition of oxide films. The periods of oscillations during the SrO growth are independent of substrate temperature, confirming that Sr atoms are oxidized immediately and stay on the substrate surface without re-evaporation. These informations are practically available for precise control of the atomic layer controlled MBE of BSCCO superconductor thin films.On leave from Superconductiivity Research Laboratory, ISTEC.     

Synthesis of boron nitride from triammoniadecaborane and hydrazine under pressure

Boron nitride (BN) of low crystallinity was synthesized from triammoniadecaborane (TAD) and hydrazine at 125 MPa below 650° C. TAD itself was pyrolysed at 600° C and 125 MPa to form a mixture of amorphous boron and boron nitride containing BH and NH bonds. The infrared spectrum of the pyrolysed product of TAD itself at 600° C and 125 MPa showed the BNB absorption at 800cm^–1 due to the formation of B₃N₃ structures. The X-ray diffraction (XRD) of the reaction product from TAD and hydrazine at 600° C had broad diffractions centred at 2=25.5° and 43.0° (CuK). The BH absorption at 2500cm^–1 decreased in intensity on increasing the N/B ratio from 0.3 to 0.85, and disappeared finally at a ratio of N/B=1.3. The reaction product at 125 MPa had a porous structure. The electron diffraction of the specimen changed from faint rings to spots on circular rings after heat treatment at 800° C for 10 h. The heat-treated specimen, however, did not give sharp reflections corresponding to hexagonal BN in the XRD profile. BN of low crystallinity was transferred to cubic BN at 1200° C and 6.5 GPa in a 90% yield, which was higher than that of well-crystallized BN in the presence of AIN.     

Preparation of TiB2 sintered compacts by hot pressing

A sintered compact of titanium diboride (TiB₂) was prepared by hot pressing of the synthesized TiB₂ powder, which was obtained by a solid-state reaction between TiN and amorphous boron. Densification of the sintered compact occurred at 20 MPa and 1800° C for 5 to 60 min with the aid of a reaction sintering, including the TiB₂ formation reaction between excess 20 at % amorphous boron in the as-synthesized powder (TiB₂ + 0.2B) and intentionally added 10 at % titanium metal. A homogeneous sintered compact of a single phase of TiB₂, which was prepared by hot pressing for 30 min from the starting powder composition [(TiB₂ + 0.2B) + 0.1 Ti], had a fine-grained microstructure composed of TiB₂ grains with diameters of 2 to 3 m. The bulk density was 4.47 g cm^–3, i.e. 98% of the theoretical density. The microhardness, transverse rupture strength and fracture toughness of the TiB₂ sintered compact were 2850 kg mm^–2, 48 kg mm^–2 and 2.4 MN m^–3/2, respectively. The thermal expansion coefficient increased with increasing temperature up to 400° C and had a constant value of 8.8 x 10^–6 deg^–1 above 500° C.     

Reaction control of TiB2 formation from titanium metal and amorphous boron

TiB₂ powder was synthesized by a controlled formation reaction from titanium metal and amorphous boron. Precursory TiB₂ formed by the pretreatment of the mixed powder (mole ratio: B/Ti=2.0) at 600° C for 60 min in an argon stream. Hollow TiB₂ powder with an average grain size of 15m was obtained by subsequent heat treatment above 900° C for more than 60 min in an argon stream. The formation reaction of TiB₂ powder was further controlled by pretreatment of the mixed powder at 600° C for 60 min in a hydrogen and argon stream and subsequent heat treatment at 1000° C for 360 min in an argon stream, when hollow-free TiB₂ powder was formed by a milder formation reaction between amorphous boron and the reformed titanium metal with hydrogen diffused lattice.     

Time-series primitive static states for detailing work state and flow of human-operated work machine

This paper proposes a quantification method for a comprehensive work flow in construction work for describing work states in more detail on the basis of analyzing state transitions of primitive static states (PSS), which consist of 16 symbolic work states defined by using on-off state of the lever operations and joint loads for the manipulator and end-effector. On the basis of the state transition rules derived from a transition-condition analysis, practical state transitions (PST), which are common and frequent transitions in arbitrary construction work, are defined. PST can be classified into essential state transition (EST) or nonessential state transitions (NST). EST extracts common phases of work progress and estimates positional relations between a manipulator and an object. NST reveals wasted movements that degrade the efficiency and quality of work. To evaluate comprehensive work flows modeled by combining EST and NST, work-analysis experiments using our instrumented setup were conducted. Results indicate that all the PSS definitely changes on the basis of PST under various work conditions, and work analysis using EST and NST easily reveals work characteristics and untrained tasks related to wasted movements.