Mesoporous g-C3N4 decorated by Ni2P nanoparticles and CdS nanorods together for enhancing photocatalytic hydrogen evolution

Ni₂P nanoparticles and CdS nanorods were grew together on a mesoporous g-C₃N₄ through a facile in-situ solvothermal approach. Under visible light (λ > 400 nm), the as-prepared ternary PCN–CdS-5% Ni₂P composite displays a high H₂ evolution rate with 2905.86 μmol g^?1 h^?1, which is about 14, 18 and 279 times that of PCN–CdS, PCN–Ni₂P and PCN, respectively. The enhanced photocatalytic activity is mainly attributed to the improved separation efficiency of the photocarriers by the type II PCN–CdS heterojunction and the effective extraction of photogenerated electrons by Ni₂P. Meanwhile, Ni₂P acts as co-catalyst to provide the photocatalytic active site for hydrogen reduction. In addition, PCN–CdS-5% Ni₂P composite exerts good stability in 12-h cycles.     

Se doped nickel-molybdenum bimetal sulfide with enhanced electrochemical activity for hydrogen evolution reaction

In this work, we synthesized Se doped MoS₂@Ni₃S₂ with nanosheets coated nanorods structure supported on Ni foam (MoNiSeS). Firstly, MoS₂@Ni₃S₂ (MoNiS) nanorods was synthesized by hydrothermal method. After selenization treatment, MoSe₂ successfully formed on the edge of MoS₂ nanosheets and particle Ni₃S₂ transformed into NiSe, in which MoSe₂ and NiSe acted as new phase in MoNiSeS. The obtained MoNiSeS only needs a low overpotential of 68 mV to reach the current density of 10 mA cm^?2, and has a low Tafel plots of 72.77 mV dec^?1 and good electrochemical durability, whose electrochemical activity is much better than that of MoNiS and NiSeS, implying the introduction of Mo and Se is beneficial to improve the electrocatalytic performance of NiS for HER. In addition, the proper amount of Mo source, which has an effect on the morphology of product, has also been investigated. For MoNiSeS, the typical nanosheets coated nanarods expose more active sites and the synergic effects is good to the improvement of the catalytic activity. Meanwhile, WNiSeS has also been prepared using the same method and the corresponding results show that the electrochemical activity of WNiSeS is much better than that of NiSeS, proving the universality of this strategy.     

基建勘探在超深井矿山建设中的应用：以思山岭铁矿为例#br#

思山岭铁矿上下采区首采开拓中段标高分别为-1 020 m和-1 200 m，地质勘查程度为详查，资源储量级别为控制的（122b）和推断的（333）。经基建巷道工程揭露，矿体赋存形态并非地质勘查时认为的“似金元宝形”向斜，而是单斜构造控制的矿体形态。详细分析了基建勘探工作在该矿建设中的作用，认为基建勘探采用探采结合、坑钻组合手段，注重综合研究概化地质模型，对矿井基建开拓设计和施工具有较好的指导作用。     

Microwave drying performance of lignite with the assistance of biomass-derived char

Microwave lignite drying with assistance of biomass-derived char was addressed and effect of bio-char on drying rate and energy consumption was investigated in this work. Effective diffusion coefficient and activation energy for the drying process were also analyzed. The results indicated the drying process was largely dependent on the variation of sample temperature. Bio-char originated from pine wood was most favorable for lignite drying, considering its better promoting effect and advanced security. There existed an optimal bio-char addition ratio for drying process at different power. The corresponding optimal ratio was 10% at 231?W and 15% at 385?W, at which the biggest drying rate and the least energy consumption were reached. It was compared lignite drying initiated at 385?W was better for energy conservation. Effective diffusivity was improved and activation energy was simultaneously reduced, with the addition of bio-char. The minimum activation energy was 15.54?W?·?g^?1, which was gained at bio-char addition ratio of 10%. The results revealed the effect of bio-char on depressing activation energy could rival that of metal-based additives. The drying process with assistance of microwave and bio-char could present technical and economical benefits on lignite upgrading.     

三维最短路径法射线追踪及改进

射线追踪技术在地震学领域有着广泛的应用，其中以最短路径算法在复杂介质中走时计算稳定性最好。理论上最短路径法的误差来源为速度模型采样误差、空间离散化误差和角度离散化的误差，由此造成网格稀疏时射线路径呈之字形，计算走时比实际走时偏大。弯曲法追踪精度高，但是射线追踪速度受初始路径与真实射线路径逼近程度制约，在复杂介质中可能找不到全局最小走时路径。最短路径法追踪出来的网格射线路径，可以作为较理想的初始路径，供弯曲法迭代优化。将最短路径法和弯曲法结合，通过射线在初始路径附近的扰动得到Fermat原理约束下的最短路径。文章对常速模型的试算，显示了改进方法对射线路径优化的作用，在模型网格稀疏的情况下效果尤其明显。本算法适用于计算三维任意复杂介质中初至波走时和射线路径，可应用于三维走时层析成像等领域。     

天然气合成油技术发展动向

介绍了天然气合成油技术，天然气石油特征及代表性工艺过程，叙述了天然气合成油发展前景。     

新型海洋涂料技术

本文综述了符合时代要求的海洋涂料新技术及其发展趋势。     

液压集成块校核软件的编制和应用

本文叙述了液压集成块校核软件的编制思想和方法，并重点介绍了编制过程中所使用的相关技术，同时给出部分源程序。