Progressive NO2 Sensors with Rapid Alarm and Persistent Memory-Type Responses for Wide-Range Sensing Using Antimony Triselenide Nanoflakes

Antimony triselenide (Sb₂Se₃) nanoflake-based nitrogen dioxide (NO₂) sensors exhibit a progressive bifunctional gas-sensing performance, with a rapid alarm for hazardous highly concentrated gases, and an advanced memory-type function for low-concentration (<1 ppm) monitoring repeated under potentially fatal exposure. Rectangular and cuboid shaped Sb₂Se₃ nanoflakes, comprising van der Waals planes with large surface areas and covalent bond planes with small areas, can rapidly detect a wide range of NO₂ gas concentrations from 0.1 to 100 ppm. These Sb₂Se₃ nanoflakes are found to be suitable for physisorption-based gas sensing owing to their anisotropic quasi-2D crystal structure with extremely enlarged van der Waals planes, where they are humidity-insensitive and consequently exhibit an extremely stable baseline current. The Sb₂Se₃ nanoflake sensor exhibits a room-temperature/low-voltage operation, which is noticeable owing to its low energy consumption and rapid response even under a NO₂ gas flow of only 1 ppm. As a result, the Sb₂Se₃ nanoflake sensor is suitable for the development of a rapid alarm system. Furthermore, the persistent gas-sensing conductivity of the sensor with a slow decaying current can enable the development of a progressive memory-type sensor that retains the previous signal under irregular gas injection at low concentrations.     

Differences in indentation and wear behaviors between the two sides of thermally tempered soda lime silica glass

Thermal tempering is an industrial process widely used to make soda lime silica (SLS) glass panels stronger and tougher. During the tempering process, the upper and bottom sides of the glass may experience different cooling rates, and thus, their properties could be different. This study characterized changes in surface composition and subsurface glass network structures as well as indentation and wear resistance properties of the air- and tin-sides of 6-mm-thick SLS window panels faced toward the upper and sliding roller sides during thermal tempering. The results showed that although the chemical and structural differences detected with X-ray photoelectron spectroscopy and specular reflection infrared spectroscopy are subtle, there are large differences in nanoindentation behaviors and mechanochemical wear properties of the SLS glass surface. The findings of this study provide further insights into the performance difference between the air- and tin-sides of the SLS glass panel treated with thermal tempering.     

In-situ measurement of reflection coefficient and its application to predicting combustion instability in a gas turbine combustor

Journal of Mechanical Science and Technology - Here, a procedure that uses in-situ data recorded by two microphones placed inside an operating gas turbine combustor to determine the reflection...     

Time-dependent crashworthiness of polyurethane foam

Mechanics of Time-Dependent Materials - Time-dependent stress–strain relationship as well as crashworthiness of polyurethane foam was investigated under constant impact energy with different...     

Multiphase topology optimization with a single variable using the phase-field design method

In this study, a multimaterial topology optimization method using a single variable is proposed by combining the solid isotropic material with penalization method and the reaction-diffusion equation. Unlike ordinary multimaterial optimization, which requires several variables depending on the number of material types, this method intends to represent various materials as one variable. The proposed method combines two special functions in the sensitivity analysis of the objective function to converge the design variable into prespecified density values defined for each of the multimaterials. The composition constraint based on a normal distribution function is also introduced to estimate the distribution of each target density value in a single variable. It enables density exchange between multiple materials by increasing or decreasing the amount of a specific material. The proposed method is applied to structural and electromagnetic problems to verify its effectiveness, and its usefulness is also confirmed from the viewpoint of cost and computation time.     

Quantitative measurements of nanoparticle layer thicknesses near the contact line region after droplet drying-out

Journal of Mechanical Science and Technology - Confocal fringe patterns of evaporating sessile drops have provided initial evidence of the presence of a sub-micron thin liquid film emanating from...     

Effect of coupling agent content on properties of composites made from polylactic acid and chrysanthemum waste

Chrysanthemum flower is among one of the highly sought after and widely planted flower crops, in particular for cultural and religious ceremonies. However, the chrysanthemum stem and stalk have little value and usually discard as by‐product waste from floristry. The objective of this research is to investigate the potential value of utilizing chrysanthemum stem and stalk as reinforcing fillers for thermoplastic composites. In this study, 2‐mm thick composite sheet containing predefined formulations of polylactic acid (PLA), chrysanthemum waste filler (CWF) ranging from 15 to 60 phr, and maleated polyethylene (MAPE) coupling agent up to 5 phr were prepared with the aid of Haake internal mixer and compression molding. The effect of MAPE loading on tensile, thermal, and morphological properties of PLA/CWF composites was investigated. The findings revealed that PLA/CWF composite attained improved tensile modulus compared to the neat PLA, and the tensile modulus increases with higher concentration of CWF. However, both tensile strength and elongation at break reduces with increase loading of CWF. Overall, PLA/CWF composites with MAPE shows better performance compared to those without MAPE, where an optimum strength of 21.8 MPa can be achieved with 60 phr CW and 3 phr MAPE. The measured tensile strength is comparable to alternatives natural fiber thermoplastic composites demonstrating its potential to be used in non‐structurally demanding application. J. VINYL ADDIT. TECHNOL., 26:10–16, 2020. © 2019 Society of Plastics Engineers     

Peptide–Peptide Co-Assembly: A Design Strategy for Functional Detection of C-peptide,A Biomarker of Diabetic Neuropathy

Diabetes-related neuropathy is a debilitating condition that may be averted if it can be detected early. One possible way this can be achieved at low cost is to utilise peptides to detect C-peptide, a biomarker of diabetic neuropathy. This depends on peptide-peptide co-assembly, which is currently in a nascent stage of intense study. Instead, we propose a bead-based triple-overlay combinatorial strategy that can preserve inter-residue information during the screening process for a suitable complementary peptide to co-assemble with C-peptide. The screening process commenced with a pentapeptide general library, which revealed histidine to be an essential residue. Further screening with seven tetrapeptide focused libraries led to a table of self-consistent peptide sequences that included tryptophan and lysine at high frequencies. Three complementary nonapeptides (9mer com-peptides), wpkkhfwgq (Trp-D), kwkkhfwgq (Lys-D), and KWKKHFWGQ (Lys-L) (as a negative control) were picked from this table for co-assembly studies with C-peptide. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) and circular dichroism (CD) spectroscopies were utilized to study inter-peptide interactions and changes in secondary structures respectively. ATR-FTIR studies showed that there is indeed inter-peptide interaction between C-peptide and the tryptophan residues of the 9mer com-peptides. CD studies of unaggregated and colloidal C-peptide with the 9mer com-peptides suggest that the extent of co-assembly of C-peptide with Trp-D is greatest, followed by Lys-D and Lys-L. These results are promising and indicate that the presented strategy is viable for designing and evaluating longer complementary peptides, as well as complementary peptides for co-assembly with other polypeptides of interest and importance. We discuss the possibility of designing complementary peptides to inhibit toxic amyloidosis with this approach.     

Phorbol 12-Myristate 13-Acetate Induced Toxicity Study and the Role of Tangeretin in Abrogating HIF-1α-NF-κB Crosstalk In Vitro and In Vivo

Phorbol 12-myristate 13-acetate (PMA) is a potent tumor promoter and highly inflammatory in nature. Here, we investigated the toxic effects of PMA on different model system. PMA (10 μg) caused chromosomal aberrations on the Allium cepa root tip and induced mitotic dysfunction. Similarly, PMA caused embryonic and larval deformities and a plummeted survivability rate on zebrafish embryo in a dose-dependent manner. Persistently, PMA treatment on immortalized human keratinocyte human keratinocyte (HaCaT) cells caused massive inflammatory rush at 4 h and a drop in cell survivability at 24 h. Concomitantly, we replicated a cutaneous inflammation similar to human psoriasis induced by PMA. Herein, we used tangeretin (TAN), as an antagonist to counteract the inflammatory response. Results from an in vivo experiment indicated that TAN (10 and 30 mg/kg) significantly inhibited PMA stimulated epidermal hyperplasia and intra-epidermal neutrophilic abscesses. In addition, its treatment effectively neutralized PMA induced elevated reactive oxygen species (ROS) generation on in vitro and in vivo systems, promoting antioxidant response. The association of hypoxia-inducible factor 1-alpha (HIF-1α)-nuclear factor kappa-light-chain-enhancer of activated b cells (NF-κB) crosstalk triggered by PMA enhanced PKCα-ERK1/2-NF-κB pathway; its activation was also significantly counteracted after TAN treatment. Conclusively, we demonstrated TAN inhibited the nuclear translocation of HIF-1α and NF-κB p65. Collectively, TAN treatment ameliorated PMA incited malignant inflammatory response by remodeling the cutaneous microenvironment.