Geopolymer assembly by emulsion templating: Emulsion stability and hardening mechanisms

This work investigates emulsion templating to synthesize hexadecane oil/geopolymer composites. In a system with hexadecane as the internal (dispersed) phase and an alkali activated continuous phase without added surfactant, adding aluminosilicate clay particles does not increase resistance against creaming or coalescence, while adding a surfactant (L35 or CTAB) stabilizes the solid-liquid interface. Infrared studies and rheological studies of the associated geopolymerization determined that the presence of the organic phase or surfactant has no significant effect on the geopolymerization kinetics, as determined by the change in time of the Si-O-T IR stretching frequency and the rheological moduli involved during the process. The stabilization of the organic template is reminiscent of Pickering emulsion even though we employ a much greater amount of inorganic material for geopolymer formation. Although the addition of surfactant has a significant effect on the behavior of the paste, the percolation of the network remains unmodified, highlighting the fact that the phenomenon is not dependent on viscosity. Finally, rheological measurements were used to obtain the mass fractal dimension of the as-made gel network, which is able to differentiate the interfacial effect between surfactant molecules with a slightly denser interphase when a cationic surfactant is used.     

探讨网络互联对嵌入式微控制器结构的影响

嵌入式控制系统正在迅速向基于CAN、802.14.5、以太网和其它网络协议的嵌入式控制网络转变。这些嵌入式网络常常通过企业内联网、外联网或互联网等与其它网络连接。随着连接性的增加,嵌入式微处理器(MCU)的结构将面临安全和带宽的问题。嵌入式系统朝着嵌入式网络的趋势发展从根     

Biological evaluation of two anomeric glucose analogues iodinated in position 6

Two anomeric analogues of glucose labelled with 123 iodine in position 6, proposed as tracers of glucose transport in vivo, have been synthesized: alpha- and beta-methyl-6-deoxy-6-iodo-D-glucopyranoside (alpha MDIG and beta MDIG). The aim of this study was to determine whether these molecules interact with the glucose transporter and whether they could be used as tracers of glucose transport in vivo. The biodistribution of alpha MDIG and beta MDIG was studied in the mouse in vivo. To determine if these two anomers enter the cell via the glucose transporter, their uptake was measured in isolated perfused rat hearts, in human erythrocytes in suspension, and in cardiomyocytes of neonatal rat in culture. Both alpha MDIG and beta MDIG had similar repartitions in the mouse: myocardial uptake averaged 7% of the injected dose/g of organ at 2 min postinjection and alpha MDIG competed with D-glucose to enter the cells. Insulin produced a 123% increase of its uptake in isolated perfused rat hearts and a 100% increase in cardiomyocytes of neonatal rat in culture. alpha MDIG uptake was lowered in the presence of glucose transport inhibitors in each experimental model. An interaction between beta MDIG and glucose transporters was observed only in human erythrocytes in suspension. Only alpha MDIG interacts with the glucose transporter, and thus could be used to estimate glucose transport in vivo.     

Evaluating part designs for automatic feeding in robotic assembly systems: A geometric analysis of the nesting of polyhedral objects

One of the problems encountered by automatic feeding devices, such as vibratory bowl feeders, in robotic assembly systems is nesting which leads to inseparability of parts and jamming. In this paper, we describe a design evaluation procedure to determine whether a part is prone to nesting and to quantify the degree of nesting. The proposed methodology reduces the 3-D protrusion-hole polyhedral containment problem of nesting to a 2-D polygon containment problem by employing a loop-based feature recognition scheme. Subsequently, the 3-D containment configuration is reconstructed from that of the 2-D by using a strategy calleddrop, pull and push. In this context, we introduce the notion of axis as a characteristic direction of a feature that facilitates the analysis of generalized 3-D polyhedral containment. The algorithms are applicable to generic B-Rep CAD data, and their time and space complexities are polynomial.     

Synthesis of 2,7‐Carbazolenevinylene‐Based Copolymers and Characterization of Their Photovoltaic Properties

New electroactive and photoactive conjugated copolymers consisting of alternating 2,7‐carbazole and oligothiophene moieties linked by vinylene groups have been developed. Different oligothiophene units have been introduced to study the relationship between the polymer structure and the electronic properties. The resulting copolymers are characterized by UV‐vis spectroscopy, size‐exclusion chromatography, and thermal and electrochemical analyses. Bulk heterojunction photovoltaic cells from different copolymers and a soluble fullerene derivative, [6,6]‐phenyl‐C₆₁ butyric acid methyl ester, have been fabricated, and promising preliminary results are obtained. For instance, non‐optimized devices using poly(N‐(4‐octyloxyphenyl)‐2,7‐carbazolenevinylene‐alt‐3″,4″‐dihexyl‐2,2′;5′,2″;5″,2″′;5″′,2″″‐quinquethiophenevinylene 1″,1″‐dioxide) as an absorbing and hole‐carrier semiconductor exhibit power conversion efficiency up to 0.8 % under air mass (AM) 1.5 illumination. These features make 2,7‐carbazolenevinylene‐based and related polymers attractive candidates for solar‐cell applications.     

Triangular ray-tube analysis of dielectric lens antennas

A new method of analysis for the radiation characteristics of dielectric lens antennas with arbitrary inner and outer surfaces is presented. The analysis is based on representing the feed illumination by a contiguous set of ray tubes and including the effects of surface reflections and ray divergence. Radiation patterns and the antenna gain are then computed by evaluating the closed-form expressions developed for the Kirchhoff's integral of the aperture fields. The validity of the analysis method has been demonstrated by comparing the computations with measured results of two different spherical lenses and a shaped lens configurations. The analysis method presented takes into account some of the practical aspects associated with lens design such as surface zoning to reduce the mass and surface matching to minimize the reflection loss     

Effects of rilmenidine on rats made insulin resistant and hypertensive by a high fructose diet

This study was aimed to determine the effects of rilmenidine, an hypertensive drug, in an animal model of hypertension associated with insulin resistance, i.e. rats fed on a high fructose diet. Wistar rats were fed during four weeks either on a standard diet (S) or on a high fructose diet (F, 34.5% de fructose). In half of the F groups, rilmenidine (1 mg/kg/day) was added to the drinking water during the two last weeks of the diet (FR). Arterial blood pressure as well as insulin efficiency were determined at the end of the four weeks. Body weight gain was higher in F than in S rats (66 +/- 8 g versus 45 +/- 8 g; p < 0.05), this was prevented by rilmenidine treatment (32 +/- 2 g). Arterial systolic blood pressure was increased in F rats (162 +/- 2 vs 155 +/- 2 mmHg; p < 0.05), rilmenidine brought this value back to normal (149 +/- 3 mmHg). During the euglycemic hyperinsulinemic clamp, glucose utilization was lower (10 +/- 1 vs 14 +/- 1.5 mg/min/kg; p < 0.05) and hepatic glucose production higher (1 +/- 0.01 vs 0 mg/min/kg; p < 0.01) in F than in S rats. These changes in insulin action were totally abolished by rilmenidine. These data demonstrate that rilmenidine can ameliorate the deleterious effects of a high fructose diet, i.e. weight gain, hypertension and resistance to the effects of insulin Rilmenidine could represent a potential therapeutic agent for the treatment of hypertension associated with metabolic disorders such as syndrom X and obesity.     

Microscale and mesoscale discrete models for dynamic fracture of structures built of brittle material

In this work we present the discrete models for dynamic fracture of structures built of brittle materials. The models construction is based on Voronoi cell representation of the heterogeneous structure, with the beam lattice network used to model the cohesive and compressive forces between the neighboring cells. Each lattice component is a geometrically exact shear deformable beam which can describe large rigid body motion and the most salient fracture mechanisms. The latter can be represented through the corresponding form of the beam constitutive equations, which are derived either at microscale with random distribution of material properties or at a mesoscale with average deterministic values. The proposed models are also placed within the framework of dynamics, where special attention is paid to constructing the lattice network mass matrix as well as the corresponding time-stepping schemes. Numerical simulations of compression and bending tests is given to illustrate the models performance.     

FDTD simulation of 30 /spl mu/m diameter polymer micro-ring

Numerical results on polymer surrounded by an air micro-ring coupled to waveguides are presented. The FDTD method predicts a filter width of 1.4 nm and an extraction efficiency of almost 80% for a gap of 0.15 /spl mu/m.     

Congenital pseudarthrosis of the clavicle

Congenital pseudarthrosis of the clavicle is a rare anomaly in which the clavicle is formed in utero in two separate segments. Clinically, there is a bump and a palpable discontinuity at the middle of the clavicle. There is no swelling or tenderness, nor disability. Radiologically, the medial ends of both clavicular segments are blunt and there is no interruption of cortical bone. The differential diagnosis includes birth fracture of the clavicle and craniocleidal dysostosis. The obstetrician should be aware of this condition as, if it is misdiagnosed, he may be wrongly accused of birth fracture.