基于空气质量模拟的江苏省大气污染物排放清单比较研究

大气污染物排放清单是空气质量模拟和空气污染治理的重要依据.本研究比较分析了两套覆盖江苏省的2017年大气污染物排放清单，即分别由上海市环境科学研究院、江苏省环境科学研究院编制的"长三角清单"和"江苏省清单"，并结合区域空气质量模型CMAQ评估不同清单对长三角地区2017年1、4、7、10月的空气质量模拟的影响.清单比较结果表明，除二氧化硫（SO₂）以外，江苏省清单估算的各污染物排放量较长三角清单低.通过与观测数据比较，发现两套清单对SO₂、氮氧化物（NO_x）、臭氧（O₃）和细颗粒物（PM_2.5）的模型模拟性能均较好.江苏省清单与长三角清单两者的模拟结果空间分布接近，其中江苏省清单模拟的PM_2.5和O₃在长三角多数地区略低于长三角清单的模拟结果（1月O₃除外）.江苏省清单与长三角清单均能够用于空气质量模式模拟，可为江苏地区的细颗粒物和光化学烟雾污染的控制策略制定提供参考.     

Ca-Mg-Al复合氧化物催化尿素与1,2-丙二醇制碳酸丙烯酯

采用共沉淀法制备了系列Ca-Mg-Al复合氧化物催化剂，通过对沉淀剂配比、沉淀液pH值及焙烧温度等制备条件的考察，得到以Na₂CO₃为沉淀剂、pH=9.5、850℃下焙烧4h制备的Ca-Mg-Al催化活性最高。在 n(PG)∶n(urea)=1.5∶1、反应温度为145℃、绝压20kPa、反应时间4h、催化剂用量为尿素质量的5%时，碳酸丙烯酯收率达到84.6%。采用XRF、XRD、NH₃-TPD、SEM及BET对催化剂的组成、晶型及酸性进行了表征，发现随着沉淀剂中Na₂CO₃的含量增加，催化剂中CaO∶MgO的比例增大，碳酸丙烯酯的收率亦升高；经850℃焙烧后，催化剂中存在CaO和MgO两种活性中心，起协同催化作用；随着焙烧温度由700℃升高到850℃，NH₃-TPD脱附曲线向低温方向偏移，且强酸中心NH₃脱附峰面积比由81.14%明显下降为0，中强酸中心NH₃脱附峰面积比由0增加到78.07%，而碳酸丙烯酯收率由68%增加到84.6%，这表明催化剂强酸性位的减少是催化活性增加的主要原因。     

Preparation and Properties of a New Mediumdensity and High-strength Ceramic Proppant

Based on the needs of the market,a new 52 MPa medium-density and high-strength ceramic proppant was prepared by adopting third grade bauxite and clay as raw materials and using the solid phase sintering method,and the effect of the firing temperature on the microstructure,phase composition and mechanical properties of the ceramic proppant was studied. The broken resistance mechanism of this ceramic proppant was also discussed. The results show that the main phases of the prepared ceramic proppant are mullite and corundum; the broken rates are 3. 92% and 7. 21% under 52 MPa and69 MPa,respectively.     

3-三氟甲基-5,6,7,8-四氢-1,2,4-三唑[4,3-α]吡嗪盐酸盐的合成

乙二胺与氯乙酸乙酯经取代、环合反应制得2-哌嗪酮,2-哌嗪酮与Boc酸酐进行氨基保护反应后,再与五硫化二磷进行硫代反应制得4-(N-叔丁氧羰基)-2-哌嗪硫酮,其与三氟乙酰肼经取代、环合、脱叔丁氧羰基成盐,得标题化合物,总收率为45.7%(以氯乙酸乙酯计)。为磷酸西他列汀中间体的工业化生产提供了一条较理想的工艺路线。     

Study on wax precipitation characteristics of wax deposit in pipes

Wax deposit properties are a significant concern in pipeline pigging during waxy crude oil transportation. In the present work, the impacts of flow conditions and oil properties on the wax precipitation characteristics of wax deposits are investigated. A flow loop apparatus was developed to conduct wax deposition experiments using four crude oils collected from different field pipes. The differential scanning calorimetry (DSC) technique was employed to observe the wax precipitation characteristics of crude oil and wax deposit. The results show that the wax content and the wax appearance temperature (WAT) of the deposits increase with shear stress and radial temperature gradient, and decrease with radial wax molecule concentration gradient near the pipe wall. The DSC tests on the wax deposits revealed that the deposit wax content is strongly correlated to the oil wax content. Furthermore, an empirical correlation was developed to predict the wax content and the WAT of the wax deposit. Verification of the empirical correlation using the different oils indicated that the average relative error of the wax content prediction and average absolute error of WAT prediction were 13.2% and 3.6°C, respectively.     

Crosslinked quaternized poly(arylene ether sulfone) copolymer membrane applied in an electric double-layer capacitor for high energy density

The low energy density of supercapacitors, especially supercapacitors based on aqueous electrolytes, is the main factor limiting their application, and the energy density is closely related to the operating potential window of the supercapacitor. The polymer electrolyte is the main contributor to the safe operation and good ion conductivity of the supercapacitor. In this study, a crosslinked quaternized poly(arylene ether sulfone) (PAES) membrane was prepared via crosslinking during membrane formation with a thermal-only treatment and applied in an electric double-layer capacitor (EDLC). The pre-prepared PAES membrane formed a polymer electrolyte with 1 mol/L Li₂SO₄ and was then fabricated into an EDLC single cell. The properties of both the membrane and ELDC were investigated. The preferred cPAES-N-0.2 polymer electrolyte showed an ionic conductivity of 1.18 mS/cm. The optimized EDLC exhibited a single-electrode gravimetric capacitance of 104.92 F/g at a current density of 1.0 A/g and a high operating potential window (1.5 V); it, thereby, achieved a high energy density of 8.20 W h/kg. The EDLC also exhibited excellent cycling properties over 3000 charge–discharge cycles. The crosslinked structures promoted the tensile strength and thermal stability of the PAES membranes; this was accompanied by a slight decrease in the ionic conductivity. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47759.     

重整生成油选择性加氢脱烯烃 Pd基催化剂的研究

 研究了负载在Al₂O₃载体上的贵金属钯(Pd)基催化剂在重整生成油选择性加氢脱烯烃反应中的性能。在高压微反装置上，采用环己烯、甲苯和正庚烷的混合物为模拟油来评价筛选催化剂，并对不同工业原料油进行加氢试验。结果表明，在现有工业上常用的工艺条件下，采用Pd/Al₂O₃催化剂进行重整生成油全馏分的选择性加氢，不能满足产品质量要求。其原因是高沸点馏分强吸附在催化剂表面，从而导致催化剂失活。在适宜的工艺条件下，采用Pd/Al₂O₃催化剂进行连续重整汽油BTX 馏分选择性加氢脱烯烃，可以使加氢汽油满足芳烃抽提进料的质量要求。添加助剂对Pd/Al₂O₃催化剂进行改进，可以大大提高催化剂的稳定性。改进后的双金属Pd基催化剂(Pd+M/Al₂O₃)可用于不同原料的重整生成油（苯(C6)馏分、BTX(C6~C9)馏分、全馏分）的选择性加氢脱烯烃反应。加氢反应产物的溴价小于200mgBr/100g，芳烃损失小于0.5%(质量分数)，且在重整生成油全馏分的选择性加氢过程中该催化剂表现出好的稳定性。     

分组空时块码系统中的排序最大信噪比检测算法

提出并比较了应用于分组空时块码（G—STBC）系统中两种不同信道模型的排序最大信噪比（MaxSNR）检测算法。该系统在发端对发射天线分组，每组进行独立的空时块码编码；在收端应用排序最大信噪比算法进行检测。由于空时块码提供了额外的时域约束，所以可以利用这个约束对信道模型进行变换，得到一个等效信道模型，然后再使用排序MaxSNR检测；当然也可以直接利用原有的信道模型，即非等效信道模型进行检测。仿真结果表明：当接收天线数不少于发射天线数的一半时，采用等效信道模型下的排序MaxSNR算法，系统的误码曲线就能保持陡降性；并且在收发天线数相同时，其性能总是优于非等效信道模型。