Thermal stability in bulk cryomilled ultrafine-grained 5083 Al alloy

Thermal stability in bulk ultrafine-grained (UFG) 5083 Al that was processed by gas atomization followed by cryomilling, consolidation, and extrusion, and that exhibited an average grain size of 305 nm, was investigated in the temperature range of 473 to 673 K (0.55 to 0.79 T _m , where T _m is the melting temperature of the material) for different annealing times. Appreciable grain growth was observed at temperatures > 573 K, whereas there was limited grain growth at temperatures < 573 K even after long annealing times. The values of the grain growth exponent, n, deduced from the grain growth data were higher than the value of 2 predicted from elementary grain growth theories. The discrepancy was attributed to the operation of strong pinning forces on boundaries during the annealing treatment. An examination of the microstructure of the alloy suggests that the origin of the pinning forces is most likely related to the presence of dispersion particles, which are mostly introduced during cryomilling. Two-grain growth regimes were identified: the low-temperature region (<573 K) and the high-temperature region (>573 K). For temperatures lower than 573 K, the activation energy of 25 ± 5 kJ/mol was determined. It is suggested that this low activation energy represents the energy for the reordering of grain boundaries in the UFG material. For temperatures higher than 573 K, an activation energy of 124 ± 5 kJ/mol was measured. This value of activation energy, 124 ± 5 kJ/mol, lies between that for grain boundary diffusion and lattice diffusion in analogous aluminum polycrystalline systems. The results show that the strength and ductility of bulk UFG 5083 Al, as obtained from tensile tests, correlate well with substructural changes introduced in the alloy by the annealing treatment.     

An EKV-based high voltage MOSFET model with improved mobility and drift model

An EKV-based high voltage MOSFET model is presented. The intrinsic channel model is derived based on the charge based EKV-formalism. An improved mobility model is used for the modeling of the intrinsic channel to improve the DC characteristics. The model uses second order dependence on the gate bias and an extra parameter for the smoothening of the saturation voltage of the intrinsic drain. An improved drift model [Chauhan YS, Anghel C, Krummenacher F, Ionescu AM, Declercq M, Gillon R, et al. A highly scalable high voltage MOSFET model. In: IEEE European solid-state device research conference (ESSDERC), September 2006. p. 270–3; Chauhan YS, Anghel C, Krummenacher F, Maier C, Gillon R, Bakeroot B, et al. Scalable general high voltage MOSFET model including quasi-saturation and self-heating effect. Solid State Electron 2006;50(11–12):1801–13] is used for the modeling of the drift region, which gives smoother transition on output characteristics and also models well the quasi-saturation region of high voltage MOSFETs. First, the model is validated on the numerical device simulation of the VDMOS transistor and then, on the measured characteristics of the SOI-LDMOS transistor. The accuracy of the model is better than our previous model [Chauhan YS, Anghel C, Krummenacher F, Maier C, Gillon R, Bakeroot B, et al. Scalable general high voltage MOSFET model including quasi-saturation and self-heating effect. Solid State Electron 2006;50(11–12):1801–13] especially in the quasi-saturation region of output characteristics.     

Methacrylic acid and dodecyl methacrylate (MAc‐DMA) hydrogel for enhanced catalytic activity of lipase of Bacillus coagulans MTCC‐6375

An alkaline thermotolerant bacterial lipase of Bacillus coagulans MTCC‐6375 was purified and immobilized on a methacrylic acid and dodecyl methacrylate (MAc‐DMA) hydrogel. The lipase was optimally bound to the matrix after 20 min of incubation at 55°C and pH 9 under shaking conditions. The matrix‐bound lipase retained approximately 50% of its initial activity at 70–80°C after 3 h of incubation. The immobilized lipase was highly active on medium chain length p‐nitrophenyl acyl ester (C: 8, p‐nitrophenyl caprylate) than other p‐nitrophenyl acyl esters. The presence of Fe³⁺, NH₄⁺, K⁺, and Zn²⁺ ions at 1 mM concentration in the reaction mixture resulted in a profound increase in the activity of immobilized lipase. Most of the detergents partially reduced the activity of the immobilized lipase. The immobilized lipase performed ～62% conversion in 12 h at temperature 55°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1420–1426, 2006     

Synthesis of ethyl propionate catalyzed by poly(N‐AEAAm‐co‐AAc)‐cl‐MBAm hydrogel‐immobilized lipase of Bacillus coagulans MTCC‐6375

A purified alkaline thermotolerant bacterial lipase of Bacillus coagulans MTCC‐6375 was efficiently immobilized onto poly(N‐AEAAm‐co‐AAc‐cl‐MBAm)‐hydrogel at pH 8.5 and at temperature 55°C in 16 h. The hydrogel‐bound matrix possessed 1.04 U/g (matrix) lipase activity with a specific activity of 1.8 U/mg of protein. The immobilized lipase resulted in formation of 52.5 mM of ethyl propionate (52% conversion) at 55°C in 9 h in n‐nonane. Ethanol and propionic acid when used in a ratio of 300 : 100 mM, respectively, in n‐nonane along with 10 mg of hydrogel‐bound lipase resulted in optimal synthesis of ethyl propionate (82.5 mM). Addition of molecular sieves (3 Å, 0.7 g/reaction volume) further enhanced the conversion rate to 82.4% resulting in 83.5 mM of ethyl propionate. Incubation temperature below or above 55°C had a marked effect on the synthesis of ethyl propionate. However, esterification performed in n‐heptane at 65°C resulted in 87.5 mM of ethyl propionate with a conversation rate of 89.3%. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Molar volume and ultrasonic studies of europium soaps in mixed organic solvents

The ultrasonic velocity and density measurements of europium soaps in a mixture of benzene and methanol (3:2, vol/vol) were used to evaluate various acoustic parameters and molar volume and to determine the critical micelle concentration. The results showed that the ultrasonic velocity, specific acoustic impedance, molar sound velocity, and molar compressibility increase, and intermolecular free length, adiabatic Compressibility, and relative association decrease with increasing concentration and chainlength of the soap. The results were interpreted in terms of soap-solvent interaction.     

Using electric actuation and detection of oscillations in microcantilevers for pressure measurements

Response characteristics of a microcantilever, such as resonant frequency, amplitude, phase and quality factor, can be used for absolute pressure measurements in the range of 10⁻⁴ to 10³ Torr. To this end, it would be very convenient to have the resonance of the microcantilever actuated and detected electrostatically. Herein, we report the nonlinear dynamics of microcantilevers under varying pressure and different gases using the harmonic detection of resonance (HDR) technique [J. Gaillard, M.J. Skove, R. Ciocan, A.M. Rao, Electrical detection of oscillations in 340 microcantilevers and nanocantilevers, Rev. Sci. Instrum. 77 (2006) 073907]. The HDR technique exploits nonlinearities in the cantilever-counter electrode system to allow electrostatic actuation and detection of the responses of the microcantilever to the pressure and gas composition. In particular, the 2nd and 3rd harmonics of the measured charge on the cantilever are investigated. The microcantilever demonstrates a quality factor of 10,000 at 10⁻³ Torr, and a usable response in the range from 10⁻³ to 10³ Torr. The use of different harmonics can enable us to adjust the range of pressures over which the sensor has an efficacious response, enhancing its sensitivity to a particular environment. The experimental results are in reasonable agreement with theoretical calculations, despite the nonlinearities involved.     

A Deep Learning Approach to Detection and Mitigation of Distributed Denial of Service Attacks in High Availability Intelligent Transport Systems

Mobile Networks and Applications - In the era of Internet of Things (IoT) powered by 5G technologies, Automobile Industry is headed towards a revolution. In Intelligent Transport Systems (ITS),...     

Building a speech recognition system with privacy identification information based on Google Voice for social robots

The Journal of Supercomputing - Currently, many smart speakers, even social robots, appear on the market to help people's lives become more convenient. Usually, people use smart speakers to...     

Biocompatible antimicrobial cotton fibres for healthcare industries: a biogenic approach for synthesis of bio‐organic‐coated silver nanoparticles

Cotton fibres coated with biogenically fabricated silver nanoparticles (SNPs) are most sought material because of their enhanced activity and biocompatibility. After successful synthesis of SNPs on cotton fibres using leaf extract of Vitex negundo Linn, the fibres were studied using diffuse reflectance spectroscopy, scanning electron microscopy, nanoparticle tracking analysis, energy dispersive X‐ray, and inductively coupled plasma atomic emission spectrometry. The characterisation revealed uniformly distributed spherical agglomerates of SNPs having individual particle size around 50 nm with the deposition load of 423 μg of silver per gram of cotton. Antimicrobial assay of cotton–SNPs fibres showed effective performance against pathogenic bacteria and fungi. The method is biogenic, environmentally benign, rapid, and cost‐effective, producing highly biocompatible antimicrobial coating required for the healthcare industry.Inspec keywords: cotton, health care, nanoparticles, coatings, silver, fibres, nanofabrication, scanning electron microscopy, X‐ray chemical analysis, atomic emission spectroscopy, plasma applications, microorganisms, biotechnologyOther keywords: biocompatible antimicrobial cotton fibre coating, healthcare industry, bioorganic‐coated silver nanoparticle synthesis, biogenically fabricated silver nanoparticle, SNP, leaf extraction, Vitex negundo Linn, diffuse reflectance spectroscopy, scanning electron microscopy, nanoparticle tracking analysis, energy dispersive X‐ray spectrometry, inductively coupled plasma atomic emission spectrometry, uniformly distributed spherical agglomerate, antimicrobial assay, pathogenic bacteria, fungi, Ag