Effect of texture on oxidation resistance of Ti3AlC2

Oxidation resistance of textured Ti₃AlC₂ ceramics was measured in the temperature range 1273–1573?K. It was found that the oxidation was markedly anisotropic and the samples exhibited a better oxidation resistance when tested along a direction transverse to the c-axis. This behavior was attributed to the rapid diffusion of Al within its basal planes to form a passivating Al₂O₃ scale and it respected Ellingham diagrams. The scales formed had different compositions depending on the testing direction; this response was clearly resulting from the crystallographic orientation. Even at 1473?K after 20?h exposure, the samples tested in a direction transverse to the c-axis showed a reduced weight gain which was 45 times lower than one seen on a basal plane.     

Sol–Gel‐Derived High‐Performance Stacked Transparent Conductive Oxide Thin Films

Single‐ and multi‐layer transparent conductive oxide (TCO) thin films exhibiting high performance, good packing density and low surface/interface roughness are deposited on silica glass substrates by the sol–gel method. The crystal and microstructural properties of the TCO thin films are evaluated as an alternate to films prepared by ultra‐high vacuum deposition. Tin‐doped indium oxide (ITO) thin films produced using a two‐step drying process showed low surface roughness because of dense packing structure not only horizontal but also vertical directions. As a result, electrical conductivity, carrier concentration, carrier mobility, and optical transmittance of 2.3 × 10³ S/cm, 8 × 10²⁰ cm^?3, 18 cm²/Vs, and over 98% at 500 nm, respectively, were achieved. A multilayer ZnO/ITO stacked structure was also fabricated using the sol–gel process. Our findings suggest that solution‐based methods show promise as an alternative to existing ultra‐high vacuum methods to fabricate TCO thin films.     

Rapid Reconstitution of Biosynthetic Machinery for Fungal Metabolites in Aspergillus oryzae: Total Biosynthesis of Aflatrem

Reconstitution of the biosynthetic machinery for fungal secondary metabolites in Aspergillus oryzae provides an opportunity both for stepwise determination of the biosynthetic pathways and the total biosynthesis of fungal natural products. However, to maximize the utility of the reconstitution system, a simple and rapid strategy for the introduction of heterologous genes into A. oryzae is required. In this study, we demonstrated an effective method for introducing multiple genes involved in the biosynthesis of fungal metabolites by using the expression vectors pUARA2 and pUSA2, each of which contains two cloning sites. The successful introduction of all the aflatrem biosynthetic genes (seven genes in total) after two rounds of transformation enabled the total biosynthesis of aflatrem. This rapid reconstitution strategy will facilitate the functional analysis of the biosynthetic machinery of fungal metabolites.     

2-Arachidonoyl glycerol suppresses gastric emptying via the cannabinoid receptor 1-cholecystokinin signaling pathway in mice

2-Monoacylglycerol (2-MAG) is one of the digestion products of dietary lipids. We recently demonstrated that a 2-MAG, 2-arachidonoyl glycerol (2-AG) potently stimulated cholecystokinin (CCK) secretion via cannabinoid receptor 1 (CB1) in a murine CCK-producing cell line, STC-1. CCK plays a crucial role in suppressing postprandial gastric emptying. To examine the effect of 2-AG on gastric emptying, we performed acetaminophen and phenol red recovery tests under oral or intraperitoneal administration of 2-AG in mice. Orally administered 2-AG (25 mg/kg) suppressed the gastric emptying rate in mice, as determined by the acetaminophen absorption test and phenol red recovery test. Intraperitoneal administration of a cholecystokinin A receptor antagonist (0.5 mg/kg) attenuated the gastric inhibitory emptying effect. In addition, both oral (10 mg/kg) and intraperitoneal (0.5 mg/kg) administration of a CB1 antagonist counteracted the 2-AG-induced gastric inhibitory effect. Furthermore, intraperitoneal 2-AG (25 mg/kg) suppressed gastric emptying. These results indicate that 2-AG exhibits an inhibitory effect on gastric emptying in mice, possibly mediated by stimulating both CCK secretion via CB1 expressed in CCK-producing cells and acting on CB1 expressed in the peripheral nerves. Our findings provide novel insights into the 2-MAG-sensing mechanism in enteroendocrine cells and the physiological role of 2-MAG.     

基于灰色神经网络的传感器分段标定

针对大量程高精度传感器不能一次完成标定实验的情况,提出一种将优化灰色GM(1,1)模型与BP神经网络相结合来预测分段标定过程中特征值缺失的方法,从而实现传感器的分段标定。首先,根据实验数据建立传统灰色GM(1,1)模型,对待标定传感器和标准传感器的测量值进行缺失数据的预测;然后,为弱化传统灰色GM(1,1)模型序列变化的幅度,提高模型的预测精度,利用中心逼近的思想对传统的GM(1,1)模型进行优化;最后,利用BP神经网络对优化的灰色GM(1,1)残差序列进行修正,以较高的精度实现对分段标定过程中缺失特征值的预测。结果表明,待标定传感器和标准传感器组合预测模型的平均残差分别为0.023%和0.401%,证明了组合预测模型的有效性。所提出方法为解决大量程高精度传感器分段标定时静态特性曲线的拟合提供了一种新思路。     

Research and Development of the Coprecipitation Process for Lanthanum Germanate Oxyapatite

Although lanthanum germanate oxyapatite (La–Ge–O) has shown good potential for use as a solid electrolyte in energy storage applications, its synthesis has been challenging by either solid‐ or solution‐state methods. In this study, a new synthesis of La–Ge–O was developed through a coprecipitation technique, in which a highly concentrated homogeneous aqueous solution of La and Ge was prepared from aqueous ammonium germanate and lanthanum nitrate solutions with the addition of dilute nitric acid. Several precipitates were formed by pH manipulation, including an amorphous material obtained at pH > 3. Compared to the individual precipitation behaviors of the parent compounds, the amorphous precipitate was formed only from the aqueous two‐component mixture, and appeared to contain both metals. This material was transformed into crystalline mixtures upon heating at 1273 K. The crystalline phases were La₂Ge₃O₉ and hexagonal‐type GeO₂ when the precipitate was formed below pH 8, and the La–Ge–O and La₂Ge₂O₇ phases when the precipitate was formed around pH 8. Product formation from the coprecipitate was discussed based on X‐ray diffraction and thermal analyses. The improved availability of La–Ge–O will allow more extensive investigations of its useful properties.     

Present Status of the Nd:YAG Thomson Scattering System Development for Time Evolution Measurement of Plasma Profile on Heliotron J

A new high repetition rate Nd:YAG Thomson scattering system is developed for the Heliotron J helical device.A main purpose of installing the new system is the temporal evolution measurement of a plasma profile for improved confinement physics such as the edge transport barrier (H-mode) or the internal transport barrier of the helical plasma.The system has 25 spatial points with ～10mm resolution.Two high repetition Nd:YAG lasers (>550mJ@ 50Hz) realize the measurement of the time evolution of the plasma profile with ～10ms time intervals.Scattered light is collected by a large concave mirror (D=800 mm,f/2.25) with a solid angle of ～100 mstr and transferred to interference filter polychromators by optical fiber bundles in a staircase form.The signal is amplified by newly designed fast preamplifiers with DC and AC output,which reduces the low frequency background noise.The signals are digitized with a multi-event QDC,fast gated integrators.The data acquisition is performed by a VME-based system operated by the CINOS.     

Experimental investigation on self-leveling behavior in debris beds

During a hypothetical core-disruptive accident in a sodium-cooled fast breeder reactor, degraded core materials can form debris beds on the core-support structure and/or in the lower inlet plenum of the reactor vessel from rapid quenching and fragmentation of core material pool. Coolant boiling may lead ultimately to leveling of the debris bed that is crucial to the relocation of molten core and heat-removal capability of the debris bed. In the present study, we elected to use depressurization boiling to simulate an axially increasing void distribution in the debris bed. Bottom-heating boiling was also chosen to confirm that characteristics of the self-leveling process do not depend on the boiling mode. Particle size (between 0.5 and 6 mm), shape (spherical and non-spherical), bed volume (between 5 and 8 l) and density (namely of alumina, zirconia, lead and stainless steel) along with boiling intensity and total volume were taken as experimental parameters to obtain the general characteristics of the self-leveling process. A series of experiments with simulant materials were conducted and analyzed in detail. The good concordance of the transient processes obtained from the different boiling methods sufficiently demonstrates that the present results obtained using the depressurization boiling method exhibit these general self-leveling characteristics. Detailed comparisons of deduced time variations of the inclination angle provides qualitative tendencies based on the experimental parameters considered influential to self-leveling behavior. The rationale behind the definition introduced for equivalent power density is also presented.