Stability enhancement of polypyrrole thin film ammonia sensor by camphor sulfonic acid dopant

Journal of Materials Science: Materials in Electronics - The main weakness of polymer gas sensors is its stability. Here, we report stability enhancement of a 100 nm polypyrrole (PPy) thin...     

4-aperture differential image motion monitor as a new approach for estimating atmospheric turbulence parameters

The present study aims to evaluate the possibility of simultaneous measurements of Fried parameter and atmospheric Zernike defocus by measuring defocus aberration with 4-aperture differential image motion monitor (DIMM) for a portable telescope. Based on the results, a relation was observed between the variances of the defocus aberration (4-aperture defocus) and Fried parameter for G-tilt and Z-tilt methods. In addition, the variance of the 4-aperture defocus was compared with those of the Zernike defocus and the conventional DIMM and the results indicated a linear relationship. Based on the telescope and 4-aperture specifications, the variance of the 4-aperture defocus was converted into the Zernike defocus or the DIMM variances. Finally, the ability of estimating atmospheric coherence time by measuring the variance of the Zernike defocus velocity or the sum of the variances of two astigmatisms velocities with 4-aperture DIMM was investigated.     

Numerical modeling of the hydraulic blade pitch actuator in a spar‐type floating wind turbine considering fault conditions and their effects on global dynamic responses

This paper deals with numerical modeling of the hydraulic blade pitch actuator and its effect on the dynamic responses of a floating spar‐type wind turbine under valve fault conditions. A spar‐type floating wind turbine concept is modeled and simulated using an aero‐hydro‐servo‐elastic simulation tool (Simo‐Riflex [SR]). Because the blade pitch system has the highest failure rate, a numerical model of the hydraulic blade pitch actuator with/without valve faults is developed and linked to SR to study the effects of faults on global responses of the spar‐type floating wind turbine for different faults, fault magnitudes, and environmental conditions. The consequence of valve faults in the pitch actuator is that the blade cannot be pitched to the desired angle, so there may be a delay in the response due to excessive friction and the wrong voltage, or slit lock may cause runaway blade pitch. A short circuit may cause the blade to get stuck at a particular pitch angle. These faults contribute to rotor imbalance, which result in different effects on the turbine structure and the platform motions. The proposed method for combining global and hydraulic actuator models is demonstrated in case studies with stochastic wind and wave conditions and different types of valve faults.     

Vibration control of laminated truncated conical shell via magnetostrictive layers

Abstract

In this study feedback control is applied to control the free vibration response of an isotropic truncated conical shell embedded with magnetostrictive layers. Classical shell theory is applied to derive the shell vibration equations. The results are derived based on the Galerkin method and the results are compared with published results and the results of finite element software in order to determine the accuracy of using method. The influence of several parameters such as the thickness of magnetostrictive layers, control gain, length and radius of the large edge of the shell on the vibration suppression of fundamental frequency is determined.     

Reliability analysis of metal‐composite adhesive joints under debonding modes I,II, and I/II using the results of experimental and FEM analyses

In the present study, the experimental and finite element (FE) analyses are first carried out to investigate the deboning behavior of metal‐composite adhesive joints under modes of I and mode II loading. To conduct an FE on the debonding propagation, cohesive zone method (CZM), as well as maximum nominal stress and energy criteria, is applied. In the reliability analysis, to achieve the probability of debonding growth (PODG), limit state functions are formulated based on the energy release rate. To that end, the first‐order reliability method (FORM), the second‐order reliability method (SORM), and the Monte Carlo simulation (MCS) are used to calculate the PODG. The effect of initial debonding length on the PODG in all mentioned modes is investigated. Results obtained from reliability analysis reveal that the random variables including the initial debonding length, width, and thickness are the most sensitive variables to ascertain the PODG.     

Multi-level cross-layer protocol for end-to-end delay provisioning in wireless multimedia sensor networks

Frontiers of Information Technology & Electronic Engineering - Rapid developments in information and communication technology in recent years have posed a significant challenge in wireless...     

Multivariable autopilot design for sounding rockets using intelligent Eigenstructure Assignment technique

When a sounding rocket rolls about its longitudinal axis, the role of angle of attack and sideslip angle exchange regularly. This interchange causes the aerodynamic moments to alternate between pitching and yawing moments, which, coupled with the moment of inertia effects, further aggravates the inertial cross-coupling. In this paper, first we analyze the cross-coupling phenomena and derive a Linear, Time-Invariant (LTI), multi input — multi output model of a spinning sounding rocket and then we design an autopilot for this system. An application of multivariable control technique is presented to the design of the autopilot. The involved controller is advanced by combining Eigenstructure Assignment (EA) approach with the Particle Swarm Optimization (PSO) algorithm. Results of linear and nonlinear simulations are reported to demonstrate the performance and stability margin of the considered autopilot.     

Synthesis of biocompatible and degradable microspheres based on 2‐hydroxyethyl methacrylate via microfluidic method

Monodisperse poly(2‐hydroxyethyl methacrylate), p‐HEMA, microspheres in size ranging from 16 to 340 (μm) were synthesized by in situ emulsion photopolymerization of HEMA monomer with polyethylene glycol diacrylate (p‐EGDA) by means of a three‐dimensional microfluidic flow‐focusing device. An aqueous solution of HEMA, p‐EGDA as chain extender and UV‐photoinitiator serving as dispersed phase formed microdroplets in a continuous oil phase mainly consisting of n‐heptane. A downward coaxial orifices design in the device led to confinement of the reaction admixtures thread to central axis of the microchannels. This design strategy could solve the wetting problem of dispersed phase with the microchannels leading to a successful production of monodisperse microspheres with size variation of less than 4%. The effects of concentration of p‐EGDA, surfactant, and flow rate ratios on microsphere size were examined. It was observed that increasing the concentration of p‐EGDA slightly increases the size whereas increasing the flow rate ratios of continuous to dispersed phase effectively decreases the size of microspheres. The rapid continuous synthesis of p‐HEMA based microspheres via the microfluidic route with reliable control over size, size distribution, and composition opens new doors for mass production of biocompatible and degradable polymeric microspheres for enormous biotechnological applications. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40925.     

Mechanical, rheological, and thermal behavior assessments in HDPE/PA-6/EVOH ternary blends with variable morphology

Visco-elastic and dielectric spectra of multiwalled carbon-nanotube reinforced silicon elastomer nanocomposites were used to study relaxation behavior. SEM photomicrographs shows well dispersion of MWCNT in elastomer matrix. In visco-elastic analysis primary relaxation was studied as a function of temperature (?100 to 100 °C) at frequency 1Hz and strain 1 %. The effect of MWCNT loadings on storage modulus, loss modulus, and loss tangent has been studied. The non-linearity in loss tangent, storage modulus and loss modulus was explained on the basis of MWCNT-elastomer interaction and the inter-aggregate attraction of MWCNT. The secondary β relaxation was studied using dielectric relaxation spectra in the frequency range of 0.1 Hz to 10⁶ Hz. The effect of MWCNT loadings on the complex and real parts of impedance was distinctly visible which has been explained on the basis of interfacial polarization of fillers in a heterogeneous medium and relaxation dynamics of polymer chains in the vicinity of fillers. The dielectric formalism has been utilized to further investigate the conductivity and relaxation phenomenon. The ‘percolation limit’ of the MWCNT in the silicon elastomer was found to be in the range of 4 phr loading.