AHMED experiments on hygroscopic and inert aerosol behaviour in LWR containment conditions: experimental results

Hygroscopic NaOH, CsI, CsOH and inert Ag aerosol behaviour at different temperatures and relative humidities (RH) has been studied in a well instrumented and controlled vessel of 1.81 m³ total free volume. Homogeneous thermal-hydraulic conditions for aerosol measurement in the vessel were achieved. The aerosol number and mass concentration were measured continuously during the experiments using a Condensation Nucleus Counter and a Tapered Element Oscillating Microbalance. The particle size distribution and chemical composition in the test conditions were measured by Berner low pressure impactors. In the case of NaOH the half life of the aerosol mass concentration was more than four times longer at low RH (22%) as compared to high RH (96%). The half lives of the CsOH and CsI aerosols were only twice as long at low RH as compared to high RH. Thus at high RH (96–97%) the half lives of CsOH and CsI were twice as long as the half life for the NaOH aerosol. The faster decay of the NaOH aerosol is due to the smaller density decrease of NaOH during water condensation. CsOH particles grew rapidly to their equilibrium size at all humidities. The measured equilibrium size for CsOH aerosol agree well with the calculated particle size at different RHs. Experimental results were also compared with calculations obtained by severe accident computer codes. These calculated results will be presented in a later paper.     

Improved Soft-Output RAKE Receiver for CDMA Mobile Terminals with High Data Rates

In this paper we propose a soft-output RAKE receiver for CDMA mobile terminals using low spreading factor and/or high-order modulation constellations for high data rates. Based on the outputs of theRAKE correlator fingers, the receiver produces symbol or bit metrics for soft decision decoding. The formulation of these metrics is derived analytically taking into account the multipath propagation, interfering users and channel estimation errors. Simulations show thata performance gain is achieved when low spreading factors or high-order modulation constellations are used.     

Advanced flaw production method for in-service inspection qualification mock-ups

One of the key issues in in-service inspection qualification is the representativeness of the defects used in qualification specimens. The best representativeness is achieved with realistic defects. However, present specimen production techniques have some significant weaknesses, such as unrealistic defects or additional alterations induced in the surrounding material. Specimens manufactured, for example, by weld implantation or with weld solidification defects always result in one or more extra weld interfaces. These interfaces can be detected by NDT. To overcome problems with the current specimens, a new defect manufacturing technique was developed. The new technique produces natural, representative defects without introducing additional weld metal or other unwanted alterations to the specimen.The new method enables artificial production of single, separate fatigue cracks by thermal loading. The method is based on a natural thermal fatigue damage mechanism and enables production of real cracks directly into the samples. Cracks are produced without welding or machining and without any preliminary surface treatment or artificial initiator such as a notch or a precrack. Single crack or a network of cracks can be induced into the base material, welded areas, HAZ, weld claddings, threaded areas, T-joints, etc. The location, orientation and size of produced cracks can be accurately controlled. Produced cracks can be used to simulate different types of service-induced cracks such as thermal fatigue, mechanical fatigue and stress corrosion cracks. It is shown that artificially produced thermal fatigue cracks correspond well with the real, service-induced cracks and overcome the problems of traditional qualification specimen manufacturing techniques.     

Polymerization mechanisms and molecular weight distribution. II. AIBN-initiated polymerization of styrene at 60°C

An experimental study was carried out on the AIBN-initiated polymerization of styrene at 60°C. The kinetic rate constants were determined by the method of moments and the MWD method, which was proposed in a previous paper. The results compared favorably with the data in the literature and the MWD method was noted to yield more consistent results than the method of moments, which indicates the importance of considering the whole molecular weight distribution. The theoretical MWD was found to approximate the experimental MWD well. The chain-transfer constant to AIBN was found to be between 0.09 and 0.14.     

On the optimality of field-line routing in massively dense wireless multi-hop networks

We consider the load balancing problem in large wireless multi-hop networks by applying the continuum approximation. The task is to find routes, geometric curves, such that the maximal traffic load in the network is minimized. In finite fixed networks, multi-path routes generally yield a lower congestion and thus allow higher throughput. In contrast, we show that in dense wireless multi-hop networks, the optimal load balancing can be achieved by a destination based single-path routing referred to as field-line routing. This is because any routing can be transformed to the corresponding field-line routing with the same or better performance, by using as paths, the field lines of the so-called destination flow associated with the original routing. The concepts are illustrated with two examples. In the case of a unit disk with unit traffic, the maximal load of 0.389 of a multi-path routing system is reduced to 0.343 by using the field-line routing. Similar improvements are also demonstrated for the unit square.     

Numerical optimization of conduction cooled current leads for low current applications

The basic design principles of current leads for superconducting magnets are well established but HTS materials and conduction cooled systems call for new numerical methods. In this paper the design of current leads was formulated as an optimization problem. Both time integration and finite differencing were examined as possible ways to compute the temperature distribution inside the leads. Three examples about optimization of conduction cooled as well as gas cooled systems are presented. First, the design of tubular normal conducting gas cooled current leads was studied. Second, normal conducting leads cooled with a two-stage cryocooler were examined. Third, the optimization was applied to current leads consisting of HTS tapes at the low temperature end of a normal conducting bar. The study took into account the magnetic field and temperature dependent voltage-current characteristics of the anisotropic Bi-2223 material. The results are compared with traditional analytical ones and the numerical optimization is shown to be an efficient design tool for both normal conducting and HTS current leads.     

Easy Algorithm Animation on the Web

The animation environment Jeliot automates visualization of algorithms over the Internet. The user can visualize algorithms of his own, not merely the selection supplied by a service provider. Jeliot is based on self-animating data types: the user selects the data objects of the source code to be visualized, and Jeliot produces the animation based on operations performed on those types. We present the design of Jeliot and the principles of its implementation. In addition, we discuss the educational applications of Jeliot.     

Compact Deep Color Features for Remote Sensing Scene Classification

Neural Processing Letters - Aerial scene classification is a challenging problem in understanding high-resolution remote sensing images. Most recent aerial scene classification approaches are based...     

Real-time effective density monitor (DENSMO) for aerosol nanoparticle production

A new instrument, density monitor (DENSMO), for aerosol particle size distribution characterization and monitoring has been developed. DENSMO is operationally simple and capable of measuring the effective density as well as the aerodynamic and the mobility median diameters with a time resolution of 1 s, from unimodal particle size distributions. The characterization is performed with a zeroth order mobility analyzer in series with a low pressure impactor and a filter stage. The operation of DENSMO was investigated with sensitivity analysis and, based on the results, optimal operation parameters were determined. DENSMO was also compared, in lab test measurements, against a reference method with several particle materials with bulk densities from 0.92 to 10.5 g/cm³. The results show that the deviation from the reference method was less than 25% for suitable materials.

Copyright © 2016 American Association for Aerosol Research