Novel catechol-derived phosphorus-based precursors for coating applications

Polymer Bulletin - Depletion of the petroleum resources and poor flame-retardant properties of the epoxy resins drive researchers to develop an epoxy resin with good heat stability from...     

Analytical Modeling of Surface Potential and Drain Current of Hetero-Dielectric DG TFET and Its Analog and Radio-Frequency Performance Evaluation

Semiconductors - In the present paper, analytical modeling of surface potential and drain current for hetero-dielectric double gate tunnel FET (HDG-TFET) has been done. The two dimensional (2D)...     

Effect of swirl and number of swirler vanes on combustion characteristics of methane inverse diffusion flame

Journal of Mechanical Science and Technology - An experimental study is performed to explore the effect of swirl and number of swirler vanes on combustion characteristics of methane inverse...     

Preparation and physicochemical study of jute and glass composites of epoxy resin of (2E, 6E)-bis(4-hydroxybenzylidene)cyclohexanone

Polymer Bulletin - Jute and glass composites of epoxy resin of (2E, 6E)-bis(4-hydroxybenzylidene)cyclohexanone (EBHBC) were prepared by compressing molding technique using three different hardeners...     

Effect of MQL and nanofluid on the machinability aspects of hardened alloy steel

Abstract

The current research comprises of various machinability aspects of 4340 hardened alloy steel which are scrutinized with in context of improvements in main cutting force, tool flank wear, crater wear, surface roughness, micro-hardness, machined surface morphology, chip morphology, chip reduction coefficient and apparent coefficient of friction under three different cutting fluid applications i.e. compressed air, water soluble coolant and nanofluid (using eco-friendly radiator coolant as the base fluid and Al₂O₃ as the nanoparticle) using uncoated cermet cutting inserts and a comparative assessment was performed to select which fluid performed better in terms of various machining attributes among three cutting fluids. The minimum quantity lubrication technique (MQL) was used in which a smaller volume of coolant sprinkled at high pressure. This method is found as the most effective alternative to minimize health risks and machining costs, which is quite high in other setups. The test specimen was machined at three different cutting speeds i.e. 100, 120 and 140?m/min along with two machining parameters i.e. feed and depth of cut were kept constant respectively at 0.2?mm/rev and 0.4?mm. Outcomes made a conclusion that Al₂O₃ enriched ecofriendly nanocoolant outperformed both compressed air and water soluble coolant in terms of every machinability aspects.     

全流程低功耗设计技术的应用

随着便携式电子设备的日益使用,要求集成电路IC及SoC的功耗越来越低。在今后日益复杂的设计中,实现一个可靠的电源网络以减小功耗变成了主要的挑战。对于使用者来说,期待每一代新产品都具有新型功能,同时也希望产品的体积小并具有较长的工作时间。解决这个难题的方法之一就是采用新型的IC设计技术,以提供小而且高效的晶体管。在整个设计流程中,为了使器件的性能和可靠性最优,电源方面的限制非常关键。例如在逻辑门应用中,由于开关从一种状态转换到另一种状态从而引起动态功耗。在开关的转换过程中,和晶体管门极相连的所有内部电容将会被…     

Validity of the PAS-ADD for detecting psychiatric symptoms in adults with learning disability (mental retardation)

The Psychiatric Assessment Schedule for Adults with Developmental Disability (PAS-ADD) is a semi-structured interview for use with respondents who have learning disability and for key informants. This report investigates the ability of the instrument to detect symptoms that had been found to exist during routine clinical assessment of the patients. Field trials involved 95 referred patients with learning disability and a key informant for each sample member. Clinical opinions of the referring psychiatrists were sought using a symptom checklist. Referrer checklist symptoms and PAS-ADD data were both factor analysed. Validity testing involved (a) computation of correlations between PAS-ADD factors and checklist data and (b) comparison of PAS-ADD and referrers' diagnoses. Results indicated good validity for the PAS-ADD in relation to psychotic symptoms and depressive symptoms. Anxiety symptom identification was not well validated, probably due to small numbers. Expansive mood identified by the referrers was not detected by the PAS-ADD because there is currently no corresponding section in the interview. Where the PAS-ADD produced a diagnosis (in 58 members of the sample), 44 were in agreement with the referrer. Probability of diagnosis by PAS-ADD increased with the number of relevant active symptoms identified by the referrer. The PAS-ADD has been shown in a previous report to have the sensitivity to detect mental disorders not known to psychiatric services. For psychotic and depressive conditions, our results showed that symptom detection was in good agreement with the information provided by the referring psychiatrists on their patients. The PAS-ADD needs a section on hypomania and further investigation of its detection of anxiety disorders.     

Flexure control using piezostack actuators: design and implementation

In this paper, the application of high control authority piezostack actuators (PSAs) for active vibration control of large-scale flexible structures is studied. The idea is to add PSAs at appropriate locations of a flexible structure in order to strengthen its stiffness characteristics. In this regard, a flexible link of a macro-micro manipulator system actuated with PSAs is considered. The design of a mechanism for converting the force produced by a PSA to a bending moment is presented and a model for a system consisting of a flexible beam and a PSA is obtained. To this end, the solution of the governing partial differential equation with nonhomogeneous boundary conditions is obtained. Using singular value decomposition of the controllability Grammian of the system, optimum values for actuator parameters are obtained. The experimental results confirm that the suggested method can open up new possibilities in active vibration control of large-scale structures that require a large amount of control authority.     

A demonstration of melt rate control during VAR of “Cracked” electrodes

A particularly challenging problem associated with vacuum arc remelting occurs when trying to maintain accurate control of electrode melt rate as the melt zone passes through a transverse crack in the electrode. As the melt zone approaches the crack, poor heat conduction across the crack drives the local temperature in the electrode tip above its steady-state value, causing the controller to cut back on melting current in response to an increase in melting efficiency. The difficulty arises when the melt zone passes through the crack and encounters the relatively cold metal on the other side, giving rise to an abrupt drop in melt rate. This extremely dynamic melting situation is very difficult to handle using standard load-cell based melt rate control, resulting in large melt rate excursions. We have designed and tested a new generation melt rate controller that is capable of controlling melt rate through crack events. The controller is designed around an accurate dynamic melting model that uses four process variables: electrode tip thermal boundary layer, electrode gap, electrode mass and melting efficiency. Tests, jointly sponsored by the Specialty Metals Processing Consortium and Sandia National Laboratories, were performed at Carpenter Technology Corporation wherein two 0.43 m diameter Pyromet® 718 electrodes were melted into 0.51 m diameter ingots. Each electrode was cut approximately halfway through its diameter with an abrasive saw to simulate an electrode crack. Relatively accurate melt rate control through the cuts was demonstrated despite the observation of severe arc disturbances and loss of electrode gap control. Subsequent to remelting, one ingot was sectioned in the “as cast” condition, whereas the other was forged to 0.20 m diameter billet. Macrostructural characterization showed solidification white spots in regions affected by the cut in the electrode.