Optical and electrical properties of ITO film on flexible fluorphlogopite substrate

Indium Tin Oxide (ITO) films were prepared, at room temperature, on a fluorphlogopite substrate using magnetron sputtering technology. At various temperatures of 500 °C, 600 °C, 700 °C, 800 °C, and 900 °C, the samples were (had) annealed for 2 h (a 2-h duration). The results showed improvement in the crystalline performance of ITO film at selected annealing temperatures, with a significant reduction in resistivity at 800 °C. The lowest resistivity is 4.08 × 10^?4 Ω-cm, which is nearly an order of magnitude lower than the unannealed sample. All samples have an average light transmittance above 85% in the visible light range (400–800 nm), and with increasing annealing temperature, the average light transmittance tends to decrease. Besides, at the sensitive wavelength of 550 nm, the light transmittance is as high as 93.74%. The sheet resistance testing of the sample was through the number of bending times, which revealed that with the increase of the number of bending, the sheet resistance increases. However, after 1200 bending times, the change rate of the sheet resistance remains below 5%. Thus, the ITO film prepared on the flexible fluorphlogopite substrate revealed excellent optical and electrical properties, good flexibility, and improved stability after high-temperature annealing, which guarantees successful application in flexible electronic devices.     

三氯乙酸终止液对木瓜蛋白酶酶活测定的影响研究

本实验研究了不同的三氯乙酸终止液,对木瓜蛋白酶酶活的影响。通过使用两种检测方法,不同配方的三氯乙酸终止液进行实验。结果表明,使用两种不同配方的三氯乙酸终止液所得的结果相差2倍多。用不同稀释浓度的三氯乙酸终止液,在高浓度时,不同浓度的三氯乙酸终止液得到的结果差别很大,随着三氯乙酸浓度的降低,所测得的酶活不断升高;但是在低浓度时,不同浓度的三氯乙酸终止液得到的结果差别不大。     

Simultaneous improvement of thermal conductivity and mechanical properties for mechanically mixed ABS/h-BN composites by using small amounts of hyperbranched polymer additives

Recently, thermal interface materials (TIMs) are in great demands for modern electronics. For mechanically mixed polymer composite TIMs, the thermal conductivity and the mechanical properties are generally lower than expected values due to the sharply increased viscosity and poor filler dispersion. This work shows that addition of a small amount of polyester-based hyperbranched polymer (HBP) avoided the trade-off in mechanically mixed ABS/hexagonal boron nitride (h-BN) composites. After adding 0.5 wt% HBP, the maximum h-BN content in the composites increased from 50 to 60 wt%. The out-of-plane, in-plane thermal conductivity, and tensile strength of ABS/h-BN with 50 wt% h-BN were 0.408, 0.517 W/mK, and 18 MPa, respectively, and were increased to 0.729, 0.847 W/mK, and 32 MPa by adding 0.5 wt% HBP, while 0.972, 1.12 W/mK, and 29.5 MPa were achieved for ABS/h-BN/HBP with 60 wt% h-BN. The morphological and rheological results proved that these enhancements are due to the improved h-BN dispersion by decreasing viscosity of composites during mixing. Theoretical modeling based on the modified effective medium theory confirmed such results and showed that the interfacial thermal resistance also decreased slightly. Thus, this work demonstrates a facile and scalable method for simultaneously improving the thermal conductivity and mechanical properties of thermoplastic-based TIMs.     

胡海陶瓷艺术作品选登

正~~     

复杂难选铁矿石悬浮磁化焙烧-高效分选技术

针对传统铁矿石磁化焙烧技术与装备存在焙烧产品质量差、产能低、能耗高和环境污染严重等问题，创造性提出了一种“预热-蓄热还原-再氧化”悬浮磁化焙烧新工艺。该工艺具有原料适应性广、焙烧产品质量均匀、回收率高、生产能耗低、无污染等特点，适合处理赤铁矿、褐铁矿、菱铁矿及其混合型难选铁矿石。通过多年的潜心基础研究与技术攻关，形成了非均质矿石颗粒悬浮态流动控制、蓄热式高效低温还原、铁物相精准调控与余热同步回收等一系列关键技术，建成了500kg/h复杂难选铁矿石悬浮磁化焙烧-高效分选半工业试验平台。     

125I粒子条联合胆道支架植入治疗恶性梗阻性黄疸22例疗效分析

【摘要】　 　目的 研究和探讨125I粒子条联合胆道支架植入治疗恶性梗阻性黄疸的临床疗效。方法 2011年6月—2013年9月收治恶性梗阻性黄疸患者40例。行胆道支架植入术治疗患者18例，为对照组；采用125I粒子条联合胆道支架植入患者22例，为观察组。两组均采用经皮肝穿刺胆道引流（PTCD）并胆道支架植入。结果 观察组与对照组的平均胆道开通时间分别为（8.7 ± 0.7）和（6.2 ± 0.4）个月，两组比较差异有统计学意义（P < 0.05）。观察组与对照组术后平均生存时间分别为（11.4 ± 0.8）和（8.7 ± 0.5）个月，生存时间的差异有统计学意义（P < 0.05）。术后近期疗效及并发症两组之间的比较无明显差异（P > 0.05），但是远期疗效有显著差异（P < 0.05）。结论 与对照组相比，观察组的术后生存时间及胆道开通时间明显延长，对于125I粒子条联合支架治疗恶性梗阻性黄疸值得进一步临床研究。
     

电动汽车动态无线电能恒功率充电

电动汽车充电时,且电池电量低于80％时,为了保证充电效率一般采用恒功率充电.在动态无线电能传输系统中,电动汽车的不断移动会导致发射线圈和接受线圈的互感系数变化,致使电动汽车充电不稳定.为实现恒功率充电,提出了一种基于模型预测控制(MPC)的动态无线电能传输系统(DWPT)恒功率输出的控制方法.通过对系统建立数学模型,对输出功率进行模型预测,建立最小化目标函数来获得期望输出功率所对应的最优占空比,使输出功率恒定.进行了模型预测控制的动态无线电能传输系统Simulink仿真,通过对比不同线圈互感系数下的输出功率,验证了该方法的可行性,并且通过搭建实物测得的数据也证实了该方法的可行性.     

Real-time molecular characterization of air pollutants in a Hong Kong residence: Implication of indoor source emissions and heterogeneous chemistry

Due to the high health risks associated with indoor air pollutants and long-term exposure, indoor air quality has received increasing attention. In this study, we put emphasis on the molecular composition, source emissions, and chemical aging of air pollutants in a residence with designed activities mimicking ordinary Hong Kong homes. More than 150 air pollutants were detected at molecular level, 87 of which were quantified at a time resolution of not less than 1 hour. The indoor-to-outdoor ratios were higher than 1 for most of the primary air pollutants, due to emissions of indoor activities and indoor backgrounds (especially for aldehydes). In contrast, many secondary air pollutants exhibited higher concentrations in outdoor air. Painting ranked first in aldehyde emissions, which also caused great enhancement of aromatics. Incense burning had the highest emissions of particle-phase organics, with vanillic acid and syringic acid as markers. The other noteworthy fingerprints enabled by online measurements included linoleic acid, cholesterol, and oleic acid for cooking, 2,5-dimethylfuran, stigmasterol, iso-/anteiso-alkanes, and fructose isomers for smoking, C₂₈-C₃₄ even n-alkanes for candle burning, and monoterpenes for the use of air freshener, cleaning agents, and camphor oil. We showed clear evidence of chemical aging of cooking emissions, giving a hint of indoor heterogeneous chemistry. This study highlights the value of organic molecules measured at high time resolutions in enhancing our knowledge on indoor air quality.