Pressure-induced transparency of MgO,Al2O3, AlN,and cBN ceramics at room temperature

The in situ axial X-ray diffraction patterns of four ceramic powder samples (MgO, Al₂O₃, AlN, and cBN) that were compressed in a diamond anvil cell under uniaxial non-hydrostatic conditions were recorded. The microscopic deviatoric stress as a function of the pressure was determined from the X-ray diffraction peak broadening analysis: the curves increased approximately linearly with the pressure at the initial compression stage and then levelled off under further compression. Pressure-induced transparency was observed in all of the samples under compression, and the pressure at the turning point on the curves of the microscopic deviatoric stress versus pressure corresponded to the pressure at which the samples became transparent. Analysis of the microstructural features of the pressure-induced transparent samples indicated that the compression caused the grains to fracture, and the broken grains bonded with each other. We demonstrated that the ceramics’ pressure-induced transparency was a process during which the grains were squeezed and broken, the pores were close between the grains, and the broken grains were re-bonded under compression.     

数据驱动的机床等待过程节能方法研究

为了降低机床等待过程中的能耗，提出了一种实时数据驱动的机床等待时间预测与节能控制方法。首先，建立了射频识别驱动的生产进度评估方法，并以生产进度数据作为输入，构建了基于堆栈降噪自编码的机床等待时间预测模型；其次，依据预测的机床等待时间，提出了机床状态切换方法，以降低机床能耗；最后，通过一个电梯零部件制造车间的案例分析，表明该方法的预测误差仅为4.1%，同时将机床等待过程能耗降低了57%，实现了制造车间的节能减排。     

超亲水毛细芯环路热管启动及热性能分析

为解决电子设备高热通量下的散热问题，采用H₂O₂氧化法对烧结毛细芯进行了超亲水改性，研究了毛细芯表面润湿性对吸液性能的影响。并将改性后的超亲水毛细芯应用到环路热管内，研究了倾斜角度及加热功率对超亲水毛细芯环路热管的换热特性的影响。实验结果表明：超亲水毛细芯的吸液速度增加，吸液时间较亲水毛细芯减小了3.52ms；与普通亲水毛细芯环路热管相比，在加热功率Q=200W时，超亲水毛细芯环路热管蒸发器中心温度降低了约6.0℃，在Q=20W时启动时间与温度分别降低了33s与2.5℃。同时发现超亲水毛细芯环路热管在正重力状态时的运行温度更低，热阻较小，最低热阻仅为0.084℃/W。     

A mini review on two-dimensional nanomaterial assembly

Two-dimensional (2D) nanomaterials have attracted a great deal of attention since the discovery of graphene in 2004, due to their intriguing physicochemical properties and wide-ranging applications in catalysis, energy-related devices, electronics and optoelectronics. To maximize the potential of 2D nanomaterials for their technological applications, controlled assembly of 2D nanobulding blocks into integrated systems is critically needed. This mini review summarizes the reported strategies of 2D materials-based assembly into integrated functional nanostructures, from in-situ assembly method to post-synthesis assembly. The applications of 2D assembled integrated structures are also covered, especially in the areas of energy, electronics and sensing, and we conclude with discussion on the remaining challenges and potential directions in this emerging field.

     

聚硅氧烷改性PBT的制备及其结构与性能研究

为了提高聚对苯二甲酸丁二醇酯(PBT)分子链段的柔顺性,选用聚硅氧烷(PDMS)对其改性。将PDMS母粒(PBT-b-PDMS)与PBT按一定质量配比进行熔融共混制得不同PDMS母粒含量的PBT-b-PDMS/PBT共混切片(简称共混切片),对共混切片的结构与性能进行了研究。结果表明:PDMS母粒中软链段PDMS质量分数约为50%,硬链段PBT质量分数约为50%;PDMS以微米级微球均匀分布于PBT连续相中形成海岛结构;PDMS母粒与PBT在共混改性过程中,不存在较强的分子作用力,两者为宏观上的相容, PDMS质量分数大于等于16%后相容性逐渐变差;随着PDMS的增加,共混切片的玻璃化转变温度逐渐降低,表面接触角先逐渐减小后增大;当PDMS添加质量分数小于16%时,共混切片的亲水性能较好。     

脉冲电沉积镍-铜合金

采用脉冲电沉积技术在304不锈钢表面制备Ni-Cu合金镀层,镀液组成和工艺条件为:NiSO4ꞏ6H2O 200g/L,CuSO4ꞏ5H2O 10 g/L,十二烷基硫酸钠0.2 g/L,柠檬酸钠80 g/L,糖精0.2 g/L,pH 4.0,温度25°C,搅拌速率30 r/min,平均电流密度40~120 mA/cm2,脉冲频率0~100 Hz,占空比20%~90%,时间30 min。研究了平均电流密度、脉冲频率和占空比对Ni-Cu合金镀层的元素组成、表面形貌和显微硬度的影响,得到较优的工艺参数为:平均电流密度40 mA/cm2,脉冲频率50 Hz,占空比60%。该条件下所得Ni-Cu合金镀层由质量分数分别为56.53%和43.47%的Ni和Cu组成,呈“菜花”状形貌,结晶细致、均匀,显微硬度为614.4 HV。     

室内机组的开发与应用

随着市场的发展,精品超市和改造店铺逐渐增多,需要一种更加适合的制冷机组来满足市场的需求。本文提供了一种新型的解决方案,解决了现有机组存在的高噪音和高成本问题,不仅提高了制冷效率,而且节约能源,保护环境。