帧中继交换技术

本文论述了帧中继交换的概念、标准，结构、特点网络式样及在互连网中的应用。     

RS码频域纠错编码在激光对潜通信信道中的实现方法

介绍了信道编码在激光对潜通信系统中的重要作用，介绍了频域编译ＲＳ码的基本方法，并给出了脉冲位置调制信道的ＲＳ码频域编译码的计算机模拟方法和结果。     

Radiation of millimeter waves from NRD leaky wave antennas withtapered transition and tuning aperture

The radiation of millimeter waves from the nonradiative dielectric (NRD) leaky wave antennas with the tapered transition and the tuning aperture is investigated. An accurate theory for the leakage constant and the phase constant of the antennas is presented, which is based on the generalized scattering parameters considering the higher-order mode interactions at the discontinuities. The associated transverse equivalent network involves the characterization of the mode couplings at two air-to-dielectric interfaces, the coupled mode analysis of the tapered transition, and the calculation of the radiation fields at the tuning aperture via the extended spectral domain approach. The interesting behavior of the present modified configuration of NRD leaky wave antennas is illustrated by typical examples. The validity of the theory is confirmed by the comparison of the theoretical results with experimental data for the limiting cases     

基于CC2430片上温度传感器的温度监控系统

由传感器、微处理器和无线通信接口组成的无线传感器网络是一门日益引起人们研究兴趣的技术。它广阔地应用于医疗卫生、环境监测等领域。论文设计并实现了一种基于无线传感器技术的温度传感器监控系统。为了降低硬件成本,利用CC2430片内温度传感器进行温度采集。论文首先介绍了CC2430芯片的技术特点、基本功能,阐述了如何利用CC2430片内温度传感器进行温度测量的系统设计,给出了误差处理方法、实验的关键程序代码和实验结果。实验结果表明,基于CC2430片上温度传感器的温度监控系统适用于对监控温度精度要求不高、需自组网的环境。     

Experimental and numerical simulation of lignite chemical looping gasification with phosphogypsum as oxygen carrier in a fluidized bed

Phosphogypsum (PG) is a solid waste produced in the wet process of producing phosphoric acid.Lignite is a kind of promising chemical raw material.However,the high sulfur of lignite limits the utilization of lig-nite as a resource.Based on fluidized bed experiments,the optimal reaction conditions for the production syngas by lignite chemical looping gasification (CLG) with PG as oxygen carrier were studied.The study found that the optimal reaction temperature should not exceed 1123 K;the mole ratio of water vapor to lignite should be about 0.2;the mole ratio of PG oxygen carrier to lignite should be about 0.6.Meanwhile,commercial software Comsol was used to establish a fuel reaction kinetics model.Through computational fluid dynamics (CFD) numerical simulation,the process of reaction in fluidized bed were well captured.The model was based on a two-fluid model and coupled mass transfer,heat transfer and chemical reac-tions.This study showed that the fluidized bed presents a flow structure in which gas and solid coexist.There was a high temperature zone in the middle and lower parts of the fluidized bed.It could be seen from the results of the flow field simulated that the fluidized bed was beneficial to the progress of the gasification reaction.     

Room-Temperature Solid-State Lithium Metal Batteries Using Metal Organic Framework Composited Comb-Like Methoxy Poly(ethylene glycol) Acrylate Solid Polymer Electrolytes

Solid polymer electrolyte with good thermal stability and flexibility is an excellent candidate for solid-state lithium metal batteries, while its low ionic conductivity caused by high crystallinity limits its application at ambient temperature. Here a metal organic framework (zeolitic imidazolate framework-8, ZIF-8) composited comb-like methoxy poly(ethylene glycol) acrylate polymer electrolyte (MCPE) with high ionic conductivity (9.96 × 10⁻⁵ S cm⁻¹ at 30 °C) is prepared by an in situ UV polymerization method. The as-prepared MCPE exhibits improved mechanical property due to the introduction of porous ZIF-8 nanofillers, which is beneficial to suppress the growth of lithium dendrites. Consequently, the LiFePO₄||MCPE||Li cells show a high capacity of 116 mAh g⁻¹ at 30 °C and 0.5 C, and maintain 89.4% of initial capacity after 150 cycles with the average Coulombic efficiency of 99.9%. These results demonstrate that the MCPE shows great potential in solid-state lithium metal batteries near room temperature.     

阴离子F掺杂SOFCs阴极La1?xSrxCo1?yFeyO3?δ的氧还原性能

固体氧化物燃料电池(SOFC)因其高效、清洁及便携性等优点被认为是当前最具应用前景的新能源技术之一。传统SOFC较高的工作温度（>800 ℃）限制了其商业推广,降低其工作温度成为当前研究的热点。钙钛矿阴极材料La_1?xSr_xCo_1?yFe_yO_3?δ(LSCF)因具有较高的电子离子混合导电性而成为中温SOFC阴极材料的较佳选择,同时实验证明F替代O位能有效提升SOFC稳定性。基于已有实验报道,本文采用第一性原理计算了F掺杂对LSCF电子结构影响、氧气分子在(100)表面吸附能的变化、阴极体内氧空位形成能及氧离子迁移活化能的影响。通过与未掺杂材料性能的比较,证明:适量F掺杂LSCF在有效提升阴极表面对氧气分子吸附能力同时能进一步提高体内氧离子迁移效率,从而提升阴极氧化还原反应能力。      

地下金属矿山斜坡道浆土路修筑工艺及应用研究

斜坡道是地下金属矿山的主要运输通道,其道路质量直接影响着矿山的安全运输和经济效益。针对斜坡道混凝土浇筑路面存在的筑路成本高、养护时间长、使用寿命短及维护困难等不足,引入浆土路修筑技术,开展了地下金属矿山斜坡道浆土路筑路材料配比试验、黏土搓条和崩解试验、水洗筛分试验,并在云南卡房分公司完成了浆土路试验路段的修筑。结果表明：浆土路筑路技术能够很好地应用于地下矿山道路修筑,具有施工工艺简单、筑路成本低、施工周期短、承载能力强、抑尘防滑和低碳环保等诸多优点,为地下金属矿山道路修筑提供了工程借鉴,对于矿山降本增效、节能减排及安全高效具有重要的意义。     

磁性塑料注射成型机设计原理

磁性塑料作为一种重要的基础材料近年来得到了不断发展和广泛应用,而注射成型是磁性塑料的一种新的成型或加工工艺,其核心技术就是磁性塑料注射成型机.分析了磁性塑料注射成型机的工作原理,提出了磁性塑料注射成型机的设计原则,给出了磁性塑料注射成型机的设计方案、主要技术参数及主要部件的设计简图,并重点讨论了磁性塑料注射成型机的主要部件--塑化和充磁系统的设计,可为塑料注射成型机的推广应用以及系列化开发提供指导和帮助.     

SBS改性沥青

介绍了沥青的特性，改性沥青的种类与性能，以及丁苯嵌段共聚物改性沥青的相容性，溶胀性，分散性等方面的研究进展，并提出了发展建议。