铝合金熔炼铸造能源与资源节约

在铝材生产中,熔炼、铸造工序是能源与资源消耗多的工序,因此,节约资源、降低烧损与能耗有着重要意义。降低能耗还可以相应地减少温室气体与有害、有毒物质排放,对环保有利。中国当前铝合金熔炼铸造能源与资源节约的主要措施:调整加工用锭坯供应结构,大幅提高电解铝厂供应的锭坯,由2013年供应的42%提高到"十三五"末的65%-70%;加快走出去的力度,到国外去办铝厂,将在国外生产的铝合金锭坯运回来,争取2020年出口的铝材与铝制品全部以进口锭坯加工,这是最大的资源与能源节约;加强废铝回收与有效再生利用;加强创新,大力采用新装备、新技术与新工艺;加强管理,精心操作,管理中还有较大的能源与资源节约潜力。     

基于小角度高位技术的钻孔初采期瓦斯治理

回采工作面初采期瓦斯涌出不均衡,易出现瓦斯超限现象。针对新源煤矿近距离煤层群开采、瓦斯涌出量大等特点,提出了小角度高位钻孔抽采治理初采期瓦斯的方法;2219工作面应用实践表明,初采期内,小角度高位钻孔抽采瓦斯纯量最高5.25m3/min,瓦斯抽采率64.02%,回风流瓦斯浓度最高为0.32%,上隅角最高瓦斯浓度0.96%,未出现瓦斯超限现象,取得了很好的初采期瓦斯治理效果。     

落葵浆果天然染料提取及对羊毛织物的染色性能

文章主要研究用水浸法提取落葵浆果天然染料及研究浸提液对羊毛织物的染色性能。以水为提取剂提取落葵浆果天然染料,探讨提取工艺中料液比、提取温度及时间等因素对落葵浆果天然染料提取效果的影响。研究结果表明,落葵浆果水浸提法优化工艺为:料液比1∶20、提取温度70℃、提取时间30 min。落葵浆果天然染料可以对羊毛织物进行染色,媒染染色与直接染色相比,染色深度深且会呈现不同的颜色。由于媒染剂的络合作用,媒染染色色牢度比直接染色普遍高1~2级。     

Effect laws and mechanisms of different temperatures on isothermal tensile fracture morphologies of high-strength boron steel

The fracture behaviour and morphologies of high-strength boron steel were investigated at different temperatures at a constant strain rate of 0.1 s-1 based on isothermal tensile tests. Fracture mechanisms were also analyzed based on the relationship between microstructure transformation and continuous cooling transformation(CCT) curves. It is found that 1) fractures of the investigated steel at high temperatures are dimple fractures; 2) the deformation of high-strength boron steel at high temperatures accelerates diffusion transformations; thus, to obtain full martensite, a higher cooling rate is needed; and 3) the investigated steel has the best plasticity when the deformation temperature is 750 °C.     

Rectangular Section Control Technology for Silicon Steel Rolling

Rectangular section control technology(RSCT)was introduced to achieve high-precision profile control during silicon steel rolling.The RSCT principle and method were designed,and the whole RSCT control strategy was developed.Specifically,RSCT included roll contour design,rolling technology optimization,and control strategy development,aiming at both hot strip mills(HSMs)and cold strip mills(CSMs).Firstly,through the high-performance variable crown(HVC)work roll optimization design in the upper-stream stands and the limited shifting technology for schedule-free rolling in the downstream stands of HSMs,a hot strip with a stable crown and limited wedge,local spot,and single wave was obtained,which was suitable for cold rolling.Secondly,an approximately rectangular section was obtained by edge varying contact(EVC)work roll contour design,edge-drop setting control,and closed loop control in the upper-stream stands of CSMs.Moreover,complex-mode flatness control was realized by coordinating multiple shape-control methods in the downstream stands of CSMs.In addition,the RSCT approach was applied in several silicon-steel production plants,where an outstanding performance and remarkable economic benefits were observed.     

服役后20号钢在低温下的力学性能研究

分析了20号无缝钢管的室温和低温力学性能,结合显微组织观察、晶粒度统计和断口分析,发现低温低应力工况下服役后20号无缝钢管的力学性能完全符合冷库用液氨管道的使用要求。     

Room Temperature Ferromagnetism in Co-doped CuAlO2 Nanofibers Fabricated by Electrospinning

One-dimensional, diluted magnetic semiconductor nanofibers have attracted increasing attention for their unique magnetic properties, large specific surface area, and high porosity. These qualities lead to excellent performance in magneto-optical devices, magnetic resonance imaging, ferrofluids and magnetic separation. The purpose of this study is to fabricate P-type one dimensional CuAlO2-based diluted magnetic semiconductor nanofibers. First, we fabricated Cu Al0.95Co0.05O2 nanofibers with an average diameter of 1 μm with the electrospinning method. The annealed nanofibers were thermally treated at a temperature of 1 100 ℃ and then shrunk to a diameter of about 650 nm. We used X-ray diffraction measurements and Raman spectra to confirm that the Cu Al0.95Co0.05O2 nanofibers had a single impurity free delafossite phase. The X-ray photoelectron spectroscopy analysis indicates that Co was present in the +2 oxidation state, resulting in an room temperature ferromagnetism in the Cu Al0.95Co0.05O2 fiber. This contrasts with nonmagnetism in pristine CuAlO2 fiber. The coercivity(Hc) value of 65.26 Oe and approximate saturation magnetization(Ms) of 0.012 emu/g demonstrate good evidence of ferromagnetism at room temperature for Cu Al0.95Co0.05O2 nanofibers.