Effect of prior oxidation on the creep behavior of NiAl-hardened austenitic steel

The effect of prior oxidation at 1473 K on the creep behavior of an Fe-Ni-Cr-Al alloy, hardened by ordered NiAl precipitates, has been investigated at 873 K over a stress range of 275 to 450 MPa. The alloy in the as-electroslag remelted (ESR) as well as the ESR-plus-hot-worked conditions was considered. Prior oxidation causes creep strengthening in the Fe-Ni-Cr-Al alloy, resulting in a decrease in minimum creep rate and increase in time to rupture, in contrast to the observations reported on nickel-based superalloys. Creep strengthening is, however, accompanied by a significant reduction in creep ductility. Oxidation-induced creep strengthening in the current alloy can be attributed to the improved adherence of surface oxide caused by the presence of yttrium. An effective stress that incorporates the contributions of load transfer as well as substructural strengthening is used to account for the observed oxidation-induced creep strengthening. While creep strengthening is more pronounced in the ESR cast alloy, the loss in creep ductility is more intense in the ESR wrought alloy. Increasing the oxidation time beyond 1 hour has a minimal effect on creep strengthening of both the alloys, though it lowers significantly the creep ductility of the wrought alloy. The observed differences in creep behavior of the alloy in the two different conditions could be attributed to the differences in grain size as well as morphology and related oxidation-induced damage.     

A.c. conductivity studies on the silver molybdo-arsenate glassy system

A new quaternary fast-ion conducting silver molybdo-arsenate [Agl-Ag₂O-(MoO₃ + As₂O₅)] (SMA) glassy system has been prepared using the melt-quenching technique for various dopant salt (Agl) concentrations by fixing the formers (MoO₃ + As₂O₅) composition and the modifier (Ag₂O) to formers (M/F) ratio. The prepared compounds were characterized by X-ray diffraction. The impedance measurements were made on different Agl compositions of the SMA glasses as a function of frequency (6.5 Hz–65 kHz) and temperature (303–343 K), using the Solatron frequency-response analyser (model 1250). The bulk conductivity and the appropriate physical model (equivalent circuit) of the SMA glass were obtained from the impedance analysis. The a.c. conductivity was calculated for different Agl compositions of SMA glasses at various temperatures and the obtained a.c. conductivity results were analysed using Jonscher's Universal Law. The conduction mechanism for the highest conducting SMA glassy compound has been explained using the diffusion path model.     

Copper coating on carbon fibres and their composites with aluminium matrix

A uniform and continuous coating of copper was given to carbon fibres by cementation or electroless techniques. In both cases, when coating thicknesses were less than 0.2 m, copper deposition was discontinuous over the fibres, and above 0.2 m, coatings were continuous. In electroless coating, about 75% of the continuously coated fibres had a coating thickness range 0.2–0.5 m and above this showed isolated dendrite deposits of copper. In the cementation process, about 75% of the continuously coated fibres had a coating thickness range 0.2–0.6 m, and above this thickness, fine crystallite-type copper deposition was found over smoothly coated copper. The ultimate tensile strength of continuously electroless-coated fibres were nearer to the uncoated fibres, suggesting defect-free coating, while fibres coated by the cementation process exhibited lower ultimate tensile strength values. The tensile fracture of both electroless- and cementation-coated fibres showed delamination of the coating, suggesting poor bonding between coating and the fibre. In composites, prepared by dispersing the coated chopped fibres in a pure aluminium matrix, uniform and random distribution of the fibres were observed without appreciable fibre-metal interaction. The CuAl₂ intermetallics were largely found in the matrix and only very small amounts were observed at fibre/matrix interfaces. Additions of about 2 wt% Mg to the matrix prior to the fibre dispersion did not appreciably change the distribution pattern of the fibres, but in addition to CuAl₂ phase, Mg₂Si phases were observed in the matrix as well as at the interface.     

Structure and properties of some vegetable fibres

The stress-strain curves for pineapple leaf fibre have been analysed. Ultimate tensile strength (UTS), initial modulus (YM), average modulus (AM) and elongation of fibres have been calculated as functions of fibre diameter test length and test speed. UTS, YM, and elongation lie in the range of 362 to 748 MN m^–2, 25 to 36 GN m^–2, and 2.0 to 2.8%, respectively for fibres of diameters ranging from 45 to 205m. UTS Was found to decrease with increasing test lengths in the range 15 to 65 mm. Various mechanical parameters show marginal changes with change in speed of testing in the range of 1 to 50 mm min^–1. The above results are explained on the basis of structural variables of the fibre. Scanning electron microscope studies of the fibres reveal that the failure of the fibres is mainly due to large defect content of the fibre bo1h along the fibre and through the cross-section, The crack is always initiated by the defective cells and further aggravated by the weak bonding material between the cells.     

Alkylation of Benzene with Isopropyl Alcohol over SAPO-5 Catalyst in an Integral Pressure Reactor

The alkylation of benzene with isopropyl alcohol was studied in an integral pressure reactor over silicon substituted aluminophosphate molecular sieves, SAPO-5. The influence of various process parameters such as temperature, pressure, time on stream, weight hourly space velocity, and mole ratio of reactants on cumene yield and selectivity were investigated. The activity of SAPO-5 was compared with that of Hbeta for this reaction under similar conditions and in the same reactor. At pressures higher than atmospheric, almost the theoretical maximum yields of cumene were achieved on this SAPO-5. Among the diisopropyl benzenes formed by the alkylation of cumene, the meta-isomer was found to form in a significant amount followed by the para-isomer. The ortho-isomer with relatively high strain energy of 4.26 kcal/mol was almost negligible. The cumene yield goes through a maximum in the temperature range 498-543 K studied. Cumene selectivity was found to decrease at higher temperatures, higher pressures and lower benzene to isopropanol mole ratios.     

Secure Key Management Based Mobile Authentication in Cloud

Authentication is important to the security of user data in a mobile cloud environment. Because of the server’s user credentials, it is subject to attacks. To maintain data authentication, a novel authentication mechanism is proposed. It consists of three independent phases: Registration, login, and authentication and key agreement. The user registers with the Registration Center (RC) by producing a secret number that isn’t stored in the phone, which protects against privileged insider attacks. The user and server generate a nonce for dynamic user identity and agree on a session secret key for safe communication. The passwords are not stored on the computer or provided in plain text, they are resistant to replay, guessing, and stolen verification attacks. The suggested protocol uses a one-way hash function and XOR operations, with the client having remote access to a large number of servers over a secure communication channel. Concentrates on HMAC and SHA3 for Collision Free Hashing and to overcome length extension attacks. HMACs are substantially less affected by collisions than their underlying hashing algorithms alone. So adding an HMAC to an MD5 or SHA hash would make it substantially more difficult to break via a rainbow table.     

Comparative amino acid and fatty acid compositions of edible gums kondagogu (Cochlospermum gossypium) and karaya (Sterculia urens)

Gum karaya and gum kondagogu are the two important commercial tree gums of India. The amino acids and fatty acid profiles of gum kondagogu and gum karaya were investigated by preparing their corresponding N-O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) derivatives for amino acids and direct trans-esterification of methyl esters for fatty acids and their subsequent analysis by a GC–MS method. The amino acids, such as, alanine, valine, methionine, tyrosine and tryptophan, were not detected in gum karaya as they were in gum kondagogu. Interestingly, the aspartic acid content (72.8 ± 3.45 μg/g) of gum kondagogu was higher than that of gum karaya (64.2 ± 2.44 μg/g). The ratios of saturated to unsaturated fatty acid in gum kondagogu and gum karaya were found to be 5:1, and 6.6:1, respectively. Among the unsaturated fatty acids, linoleic acid (1.8 ± 0.12 μg/g) and γ-linolenic acid (0.8 ± 0.05 μg/g) were detected only in gum kondagogu. Arachidic acid was not detected in gum karaya. Additionally, the presence of linoleic acid and γ-linolenic acid in gum kondagogu reinforces its nutritional value.