Study on single and binary catalytic systems of pyridine-imine catalysts based on nickel and iron in synthesis of reactor blends and low-density polyethylene nanocomposites

In the presence of modified methylaluminoxane as cocatalyst, the behavior of a binary catalytic system based on pyridine-imine nickel ( N ) and iron ( F ) catalysts was evaluated in order to reach a proper mixture of polyethylene (PE). A computational study along with kinetic profile suggested that the catalyst F with higher electron affinity (A) and electrophilicity (ω) in the methyl cationic active center and stronger interaction with the monomer led to high integrated monomer consumption and higher activity. In addition, the samples produced by the mixture of catalysts showed a higher value of [19.4 × 10⁴ g (PE) mol (Fe+Ni)⁻¹ h⁻¹)], melting point (127.8 °C), and crystallinity extent (41.29%) than the samples produced by the single catalysts. The addition of multiwalled carbon nanotubes (MWCNT) into the polymerization media reduced the activity of catalysts [from 7.50 × 10⁴ to 0.66 × 10⁴ g (PE) mol (Fe+Ni)⁻¹ h⁻¹] and the thermal properties of the low-density polyethylene nanocomposite samples. However, the sample containing 2.33% MWCNT_20-30 improved the total thermal stability of the neat polyethylene blend up to 400 °C. Scanning electron microscope images of the samples demonstrated irregular to virtually uniform morphologies were obtained through the in situ and solution-mixing techniques. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47376.     

Calf massager: Intervention for body muscle discomfort during prolonged standing

Many occupations require workers to stand for long periods of time without proper interventions, which causes discomfort in the back and lower limbs. Therefore, this study aims to assess the effectiveness in alleviating body muscle discomfort during prolonged standing through the use of a calf massager. This study was conducted among male workers at a manufacturer with production line workers and the list was obtained from the HR Department and simple random sampling was done by number categorization. A total of 100 respondents (50 respondents for both the control and the experimental groups) participated in this study. The experiment took place in a room with a similar setup for the production line. Each respondent was requested to perform the simulated task for 2 hr. For the experimental group, the calf massager was turned on every 15 min. At every 15‐min interval after turning on the calf massager, respondents from both groups were required to evaluate their discomfort level on a Borg's scale CR‐10 questionnaire. The results showed that the level of body discomfort among respondents in the experimental group reduced (20–30%) compared with that of the control group. Multivariate analysis results revealed that the discomfort rating for the lower back, knees, thighs, calves, and feet was significantly lower (p < .05) among the experimental group compared with the control group. For lower body parts, the lower back region was statistically significant (p < .05) at the 90th, 105th, and 120th min; the thigh region was statistically significant (p < .05) at the 120th min; the knee region was statistically significant (p < .05) at the 105th and 120th min; the calf region was statistically significant (p < .05) at all minute intervals except the 15th and 45th min, while the feet region, was statistically significant at the 105th and 120th min. Therefore, this study indicates that calf massage treatment is capable of reducing body muscle discomfort during prolonged standing and highlights the significance of calf massage.     

Characterization,in vitro bioactivity and biological studies of sol-gel-derived TiO2 substituted 58S bioactive glass

Bioactive glasses (BGs) have been used for bone formation and bone repair processes in recent years. This study investigated the titanium substitution effect on 58S BGs (Ti-BGs) 60SiO₂-(36 − X)CaO-4P₂O₅-XTiO₂ (X = 0, 3, and 5 mol.%) prepared by the sol-gel technique, and the main goal was to find the optimum amount of titanium in Ti-BGs. Synthesized BGs, which were investigated after immersion in simulated body fluid (SBF), were tested by X-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy. Moreover alkaline phosphate (ALP) activity, 3-(4,5dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay, and antibacterial studies were employed to investigate the biological properties of Ti-BGs. According to the FTIR and XRD test results, hydroxyapatite (HA) formation on Ti-BGs surfaces was confirmed. Meanwhile, the presence of 5 mol.% compared to 3 mol.% increased the HA grain distribution and their size on the Ti-BGs surface. Additionally, MTT and ALP results confirmed that the optimal amount of titanium substitution in BG was 5 mol.%. Since 5 mol.% Ti incorporated BG (BG-5) had the highest biocompatibility level, antibacterial properties, maximum cell proliferation, and ALP activity among the synthesized Ti-BGs, it is presented as the best candidate for further in vivo investigations.     

Compressive strength and wear properties of SiC/Al6061 composites reinforced with high contents of SiC fabricated by pressure-assisted infiltration

Pressure-assisted infiltration was used to synthesize SiC/Al 6061 composites containing high weight percentages of SiC. A combination of PEG and glass water was used to fabricate SiC preforms and the effect of the presence of glass water on the microstructure and mechanical properties of the preforms was evaluated by performing compression tests on the preforms. Also, the compressive strength and the hardness of the SiC/Al composites were investigated. The results revealed that the glass water improved the compressive strength of the preforms by about five times. The microstructural characterization of the composites showed that the penetration of the aluminum melt into the preforms was completed and almost no porosity could be seen in the microstructures of the composites. Moreover, the composite containing 75 wt% SiC exhibited the highest compressive strength as well as the maximum hardness. The results of the wear tests showed that increasing the SiC content reduces the wear rate so that the Al-75 wt% SiC composite has a lower wear rate and a lower coefficient of friction than those of Al-67 wt% SiC composite. This indicated higher wear resistance in these composites than the Al alloy due to the formation of a tribological layer on the surface of the composites.     

CdSnO3/SnD NPs as a Nanocatalyst for Carbonylation of o-Phenylenediamine with CO2

Catalysis Letters - In order to carbonize o-phenylenediamine with CO2, an effective approach was used with UV light irradiation by Sn(IV) doping DFNS (SnD) supported CdSnO3 as a catalyst...     

Software assurance practices for mobile applications

Mobile software applications have to cope with a particular environment that involves small size, limited resources, high autonomy requirements, competitive business models and many other challenges. To provide development guidelines that respond to these needs, several practices have been introduced; however, it is not clear how these guidelines may contribute to solve the issues present in the mobile domain. Furthermore, the rapid evolution of the mobile ecosystem challenges many of the premises upon which the proposed practices were designed. In this paper, we present a survey of the literature on software assurance practices for mobile applications, with the objective of describing them and assessing their contribution and success. We identified, organized and reviewed a body of research that spans in three levels: software development processes, software product assurance practices, and software implementation practices. By carrying out this literature survey, we reviewed the different approaches that researchers on Software Engineering have provided to address the needs that raise in the mobile software development arena. Moreover, we review the evolution of these practices, identifying how the constant changes and modernization of the mobile execution environment has impacted the methods proposed in the literature. Finally, we introduced discussion on the application of these practices in a real productive setting, opening an area for further research that may determine if practitioners have followed the proposed assurance paradigms.     

Intrinsic CFRP-metal-hybrids with rubber interface for the improvement of the damping behaviour

This paper presents an integrated passive damping approach in hybrid metal-CFRP parts for structural applications. In this concept a viscoelastic material is embedded in the joint zone of the hybrid component. To examine the connection strength single-lap-joint specimens were produced and tested and the influence of the used material combinations, different surface structures, and different process parameters i.e. the moment of cross-linking were evaluated. Afterwards, the metal-CFRP hybrids were tested in quasi-static tests to assess their connection strength and failure behaviour. Dynamic cyclic tensile tests with step-wise increased loading conditions were performed to determine the specimens damping behaviour and to estimate their fatigue performance. Finally, these results are compared to a state of the art metal-CFRP hybrid with rivets connecting both materials.     

On stochastic comparisons of finite mixtures for some semiparametric families of distributions

In this paper, we consider the classical finite mixture model, which is an effective tool for modeling lifetime distributions for random samples from heterogeneous populations. We discuss new results on stochastic comparison for two finite mixtures when each of them is drawn from one of the following semiparametric families, i.e., proportional hazards, accelerated lifetime and proportional reversed hazards.