The effect of rice bran on physicochemical,textural and glycaemic properties of ready-to-eat extruded corn snacks

In this work, corn extruded snack products were enriched with rice bran (RB) at 10% and 15%. A co-rotating twin-screw extruder was used with a feed moisture content of 16 g 100 g⁻¹, a screw speed of 240 r.p.m. and four heating sections of the barrel (100, 140, 150 and 150 °C). The impact of RB inclusion on nutritional profile, starch digestion, physicochemical and textural properties of snack products was evaluated. RB-enriched extrudates showed a lower specific volume and hardness and higher crispness than control. RB at 15% gave a water-holding capacity lower than control. Rheology of extrudate dispersions indicated an increase in elastic interactions and solid-like behaviour with RB supplementation. Differences in rheological properties resulted in attenuation of predictive glycaemic response for RB-enriched snacks.     

Strain‐rate‐dependent mechanical properties of polypropylene separator for lithium‐ion batteries

The mechanical integrity of battery separators is critical for battery safety and durability. A comprehensive study of strain‐rate‐dependent tensile and puncture properties of a polypropylene lithium‐ion battery separator is presented here with a new model. Due to anisotropy of the polymeric membrane, tensile testing was conducted for different directions. Results showed that tensile strength and elastic modulus were increased 1000% and 500%, respectively, for different directions. It was also demonstrated that tensile strength changed 10 to 25% with strain rate (1.67 × 10^?4 to 1.67 × 10^?1 s^?1) for different directions. An equation was obtained for the first time for flow stress versus strain rate at varied tensile directions with respect to machine direction. Moreover, puncture testing was performed and it was shown that puncture strength was increased 140% with increasing strain rate from 0.25 to 250 mm min^?1. Two failure modes were also observed in puncture samples. Finally, Eyring's model was used to calculate activation enthalpy of the porous polypropylene separator. © 2020 Society of Chemical Industry     

Electrical and mechanical properties of BZT − xBCT lead-free piezoceramics

In this study, lead-free (1 − x)Ba(Zr_0.2Ti_0.8)O₃ − x(Ba_0.7Ca_0.3)TiO₃ compositions are synthesized via conventional solid oxide route, and the ceramics are fabricated with normal sintering in air. The effects of composition fluctuations on dielectric, piezoelectric, and mechanical properties are investigated. The phase structure and the microstructure are analyzed with X-ray diffraction and scanning electron microscopy. The best dielectric and piezoelectric properties of ε_r = 11 207 and d₃₃ = 330 pC/N were obtained for BZT−0.35BCT and BZT−0.5BCT ceramics, respectively. The mechanical behavior—in terms of Vickers hardness and compressive and flexural strengths—was investigated, and the best mechanical behavior was found in the vicinity of the phase transition boundary with x values between 0.5 and 0.6.     

Cit-CSP及其应用

介绍了Cit-CSP--Cit/E-commerce信息安全保障平台子系统，并阐述了它所提供的消息摘要、块加密、加密(公钥)、签名和MAC等功能和服务。     

An Insight View on Synthetic Protocol,Surface Activity,and Biological Aspects of Novel Biocompatible Quaternary Ammonium Cationic Gemini Surfactants

In this study, we prepared a novel series of diester-functionalized cationic gemini surfactants (C_m-E2O2-C_m) containing ethylene oxide as a spacer with varying alkyl chain lengths and characterized by ¹H NMR, FT-IR, elemental analysis, and ESI-MS. The physicochemical properties of the geminis were explored by tensiometry, fluorescence, dye solubilization, and Krafft point. These geminis acquire superior surface activity than the conventional surfactants. Fluorescence spectroscopy analysis affirmed that the micropolarity and aggregation number of micelles diminished with increase in the alkyl chain length. These geminis represent a new group of amphiphiles of considerably high biodegradability, better cleavability, and low toxicity as assessed by BOD test, FT-IR analysis, and HC₅₀ analysis, respectively. They also showed significant level of antimicrobial activity toward some specified bacterial strains of Gram-positive and Gram-negative by using agar well diffusion method. Furthermore, the thermogravimetric analysis provided information regarding thermal stabilities of the newly synthesized gemini surfactants.     

Effect of Extraordinary Large Floods on at-site Flood Frequency

The peak flow of extraordinary large floods that occur during a period of systematic record is a controversial problem for flood frequency analysis (FFA) using traditional methods. The present study suggests that such floods be treated as historic flood data even though their historical period is unknown. In this paper, the extraordinary large flood peak was first identified using statistical outlier tests and normal probability plots. FFA was then applied with and without the extraordinary large floods. In this step, two goodness-of-fit tests including mean absolute relative deviation and mean squared relative deviation were used to identify the best-fit probability distributions. Next, the generalized extreme value (GEV), three-parameter lognormal (LN3), log-Pearson type III (LP3), and Wakeby (WAK) probability distributions were used to incorporate and adjust the extraordinary large floods with other systematic data. Finally, procedures with and without historical adjustment were compared for the extraordinary large floods in terms of goodness-of-fit and flood return-period quantiles. The results of this comparison indicate that historical adjustment from an operational perspective was more viable than without adjustment procedure. Furthermore, the results without adjustment were unreasonable (subject to over- and under-estimation) and produced physically unrealistic estimates that were not compatible with the study area. The proposed approach substantially improved the probability estimation of rare floods for efficient design of hydraulic structures, risk analysis, and floodplain management.     

Design and simulation of a novel metallic microgripper using vibration to release nano objects actively

In this study, we investigate a novel metallic microgripper which is able to grasp and transport nano particles (nano tubes/wires) and release them on desirable substrate by vibrating the gripper arms. This microgripper consists of a chevron actuator to grip nano object electrothermally and interdigited comb drive systems to generate vibration at the gripper arms electrostatically. Metallic (nickel) properties enable the chevron actuator to close the gap and pick the nano particle at low voltage and temperature. In order to reduce the out of plane bending during operation and also increase the gripping force, thickness of the nickel layer must be increased, hence electroplating process is proposed for deposition of nickel layer. To generate vibration at the end effectors, comb drive systems are stimulated by applying two voltage signals at desired resonant frequency to the stators. Practically, by sweeping the frequency of these signals around the resonant frequency the end effectors start vibrating. The vibration results in overcoming the adhesion forces due to inertial effects.     

Support vector regression methodology for prediction of input displacement of adaptive compliant robotic gripper

The prerequisite for new versatile grippers is the capability to locate and perceive protests in their surroundings. It is realized that automated controllers are profoundly nonlinear frameworks, and a faultless numerical model is hard to get, in this way making it troublesome to control utilizing tried and true procedure. Here, a design of an adaptive compliant gripper is presented. This design of the gripper has embedded sensors as part of its structure. The use of embedded sensors in a robot gripper gives the control system the ability to control input displacement of the gripper and to recognize specific shapes of the grasping objects. Since the conventional control strategy is a very challenging task, soft computing based controllers are considered as potential candidates for such an application. In this study, the polynomial and radial basis function (RBF) are applied as the kernel function of Support Vector Regression (SVR) to estimate and predict optimal inputs displacement of the gripper according to experimental tests and shapes of grasping objects. Instead of minimizing the observed training error, SVR _poly and SVR _rbf attempt to minimize the generalization error bound so as to achieve generalized performance. The experimental results show that an improvement in predictive accuracy and capability of generalization can be achieved by the SVR approach compared to other soft computing methodology.     

Nonflat surface level pyramid: a high connectivity multidimensional interconnection network

Parallel machines are extensively used to increase computational speed in solving different scientific problems. Various topologies with different properties have been proposed so far and each one is suitable for specific applications. Pyramid interconnection networks have potentially powerful architecture for many applications such as image processing, visualization, and data mining. The major advantage of pyramids which is important for image processing systems is hierarchical abstracting and transferring the data toward the apex node, just like the human being vision system, which reach to an object from an image. There are rapidly growing applications in which the multidimensional datasets should be processed simultaneously. For such a system, we need a symmetric and expandable interconnection network to process data from different directions and forward them toward the apex. In this paper, a new type of pyramid interconnection network called Non-Flat Surface Level (NFSL) pyramid is proposed. NFSL pyramid interconnection networks constructed by L-level A-lateral-base pyramids that are named basic-pyramids. So, the apex node is surrounded by the level-one surfaces of NFSL that are the first nearest level of nodes to apex in the basic pyramids. Two topologies which are called NFSL-T and NFSL-Q originated from Trilateral-base and Quadrilateral-base basic-pyramids are studied to exemplify the proposed structure. To evaluate the proposed architecture, the most important properties of the networks are determined and compared with those of the standard pyramid networks and its variants.