Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Modification of hypoeutectic low alloy white cast irons

In order to modify the continuous network of eutectic cementite normally found in low alloy white cast irons into a dispersive distribution, strategies of controlling the morphology of eutectic cementite by additives are discussed. Qualitative arguments are presented and applied to the development of a complex modifier REAINTi. With the addition of this modifier to low carbon white cast irons nearly one fifth of the original eutectic cementite network can be modified into blocky particles in the plane of polish, and one third into isolated irregular ones. The experimental data shows that Ti(CN) may act as an effective nucleant or a grain refiner for eutectic cementite. The modification effects of rare earth elements are attributed to their abilities to purify the melt, promote divorced eutectic growth and refine the microstructure. Aluminium contributes to the modification by its purification effect.     

Conservation and Improvement of the Natural Environment in Reservoir Watersheds in Japan

This paper discusses environmental conservation in reservoir watersheds, an important aspect relating to dam construction. The discussion of the subject describes how, in response to today's growing awareness of environmental issues, measures to absolutely minimize the effects on the environment of a dam project that will submerge the natural environment should be included in initial project plans, and how special concern for the environment ought to be shown throughout project implementation. Details are explained by introducing examples encountered in Japan.     

Design for Consecutive Testability of System-on-a-Chip with Built-In Self Testable Cores

This paper introduces a new concept of testability called consecutive testability and proposes a design-for-testability method for making a given SoC consecutively testable based on integer linear programming problem. For a consecutively testable SoC, testing can be performed as follows. Test patterns of a core are propagated to the core inputs from test pattern sources (implemented either off-chip or on-chip) consecutively at the speed of system clock. Similarly the test responses are propagated to test response sinks (implemented either off-chip or on-chip) from the core outputs consecutively at the speed of system clock. The propagation of test patterns and responses is achieved by using interconnects and consecutive transparency properties of surrounding cores. All interconnects can be tested in a similar fashion. Therefore, it is possible to test not only logic faults but also timing faults that require consecutive application of test patterns at the speed of system clock since the consecutively testable SoC can achieve consecutive application of any test sequence at the speed of system clock.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Crack opening displacement of a through-wall crack in a plate subjected to bending load

This study was performed in order to clarify crack opening displacement (COD) of through-wall cracks in a plate subjected to bending load. The former COD evaluation methods were mainly developed corresponding to tensile load, but there has been nothing that has been developed corresponding to bending load. Therefore, the authors evaluated CODs of the through-wall cracks in plates which were subjected to a bending load using finite element method (FEM) analyses, and proposed a simplified COD evaluation method accounting for both tensile and bending loads. The proposed method is useful for leakage evaluation at a crack opening of an elbow crown or in the vicinity of the coolant surface of a vessel in which the bending stress is relatively large.     

Subsurface structures in initial stage of FeSi2 growth studied by high-resolution Rutherford backscattering spectroscopy

The initial stage of iron silicide formation is investigated by high-resolution Rutherford backscattering spectroscopy. During the Fe deposition on Si(001) at 470 °C, the formation of FeSi₂ is confirmed by the surface peak analysis. Initially, FeSi₂ grows epitaxially so that one of the major crystallographic axes is parallel to the <111> axis of the Si substrate. With increasing Fe deposition, the deviation between the major crystallographic axis of the silicide region and Si<111> increases although the electron diffraction pattern is independent of the amount of Fe deposition. Therefore, the subsurface crystallographic structure of iron silicide is transformed from a cubic-like to a low-symmetry structure.     

Survey of switching techniques in high-speed networks and their performance

One of the most promising approaches for high speed networks for integrated service applications is fast packet switching, or ATM (asynchronous transfer mode). ATM can be characterized by very high speed transmission links and simple, hard-wired protocols within a network. To match the transmission speed of the network links, and to minimize the overhead due to the processing of network protocols, the switching of cells is done in hardware switching fabrics in ATM networks. A number of designs have been proposed for implementing ATM switches. Although many differences exist among the proposals, the vast majority of them are based on self-routeing multistage interconnection networks. This is because of the desirable features of multi-stage interconnection networks such as self-routeing capability and suitability for VLSI implementation. Existing ATM switch architectures can be classified into two major classes: blocking switches, where blockings of cells may occur within a switch when more than one cell contends for the same internal link, and non-blocking switches, where no internal blocking occurs. A large number of techniques have also been proposed to improve the performance of blocking and non-blocking switches. In this paper, we present an extensive survey of the existing proposals for ATM switch architectures, focusing on their performance issues.     

Data fitting with a spline using a real-coded genetic algorithm

To obtain a good approximation for data fitting with a spline, frequently we have to deal with knots as variables. The problem to be solved then becomes a continuous nonlinear and multivariate optimization problem with many local optima. Therefore, it is difficult to obtain the global optimum. In this paper, we propose a method for solving this problem by using a real-coded genetic algorithm. Our method can treat not only data with a smooth underlying function, but also data with an underlying function having discontinuous points and/or cusps. We search for the best model among candidate models by using the Bayes Information Criterion (BIC). With this, we can appropriately determine the number and locations of knots automatically and simultaneously. Five examples of data fitting are given to show the performance of our method.