The effect of rice bran on physicochemical,textural and glycaemic properties of ready-to-eat extruded corn snacks

In this work, corn extruded snack products were enriched with rice bran (RB) at 10% and 15%. A co-rotating twin-screw extruder was used with a feed moisture content of 16 g 100 g⁻¹, a screw speed of 240 r.p.m. and four heating sections of the barrel (100, 140, 150 and 150 °C). The impact of RB inclusion on nutritional profile, starch digestion, physicochemical and textural properties of snack products was evaluated. RB-enriched extrudates showed a lower specific volume and hardness and higher crispness than control. RB at 15% gave a water-holding capacity lower than control. Rheology of extrudate dispersions indicated an increase in elastic interactions and solid-like behaviour with RB supplementation. Differences in rheological properties resulted in attenuation of predictive glycaemic response for RB-enriched snacks.     

Strain‐rate‐dependent mechanical properties of polypropylene separator for lithium‐ion batteries

The mechanical integrity of battery separators is critical for battery safety and durability. A comprehensive study of strain‐rate‐dependent tensile and puncture properties of a polypropylene lithium‐ion battery separator is presented here with a new model. Due to anisotropy of the polymeric membrane, tensile testing was conducted for different directions. Results showed that tensile strength and elastic modulus were increased 1000% and 500%, respectively, for different directions. It was also demonstrated that tensile strength changed 10 to 25% with strain rate (1.67 × 10^?4 to 1.67 × 10^?1 s^?1) for different directions. An equation was obtained for the first time for flow stress versus strain rate at varied tensile directions with respect to machine direction. Moreover, puncture testing was performed and it was shown that puncture strength was increased 140% with increasing strain rate from 0.25 to 250 mm min^?1. Two failure modes were also observed in puncture samples. Finally, Eyring's model was used to calculate activation enthalpy of the porous polypropylene separator. © 2020 Society of Chemical Industry     

Electrical and mechanical properties of BZT − xBCT lead-free piezoceramics

In this study, lead-free (1 − x)Ba(Zr_0.2Ti_0.8)O₃ − x(Ba_0.7Ca_0.3)TiO₃ compositions are synthesized via conventional solid oxide route, and the ceramics are fabricated with normal sintering in air. The effects of composition fluctuations on dielectric, piezoelectric, and mechanical properties are investigated. The phase structure and the microstructure are analyzed with X-ray diffraction and scanning electron microscopy. The best dielectric and piezoelectric properties of ε_r = 11 207 and d₃₃ = 330 pC/N were obtained for BZT−0.35BCT and BZT−0.5BCT ceramics, respectively. The mechanical behavior—in terms of Vickers hardness and compressive and flexural strengths—was investigated, and the best mechanical behavior was found in the vicinity of the phase transition boundary with x values between 0.5 and 0.6.     

Mechanisms of orientational and photoelastic birefringence generation of methacrylates for the design of zero–zero‐birefringence polymers

The intrinsic birefringence Δn⁰ and photoelastic coefficient C of poly(methyl methacrylate), poly(2,2,2‐trifluroethyl methacrylate), poly(phenyl methacrylate), and poly(2,2,3,3,3‐pentafluorophenyl methacrylate) were determined. We categorized these methacrylate polymers into four birefringence‐types, even though their molecular structures differed only by the substituents on the side chains. Based on the results of Δn⁰ and C, novel polymers that exhibit neither orientational nor photoelastic birefringence, i.e., zero–zero‐birefringence polymers, were designed and synthesized by quaternary copolymerization system. Furthermore, we confirmed that the mechanisms of orientational birefringence and photoelastic birefringence generation were different in these methacrylate polymers. The conformation of the repeat unit of the polymers was nearly constant during the generation of orientational birefringence. In contrast, the conformation of the repeat unit of the polymers changed during the generation of photoelastic birefringence in the glassy state. These findings demonstrated the reasonability of evaluating orientational and photoelastic birefringence separately, as well as the adequacy of the classification of polymers into four birefringence‐types. Given these results and the fact that zero–zero‐birefringence polymers could be prepared successfully by four‐birefringence type monomers, we demonstrated the reasonability of the method for designing the zero–zero‐birefringence polymers. POLYM. ENG. SCI., 55:1330–1338, 2015. © 2015 Society of Plastics Engineers     

Cit-CSP及其应用

介绍了Cit-CSP--Cit/E-commerce信息安全保障平台子系统，并阐述了它所提供的消息摘要、块加密、加密(公钥)、签名和MAC等功能和服务。     

Two-dimensional ultrasonic tomography in nondestructive evaluation by using area functions

It is shown that the (normalized) area function based on the Born approximation offers a simple connection between the ultrasonic scattering response and the monochromatic ray sum in X-ray CT (computerized tomography). Because of this simple association, it is possible to apply the ultrasonic signals in the computationally direct and efficient parallel-beam X-ray CT algorithm to reproduce the vertical thickness function of an ultrasonic scatterer. The development of this imaging methodology is demonstrated for flaws of simple geometry; theoretical as well as experimental results for two model scatterers using this imaging technique are reported. Specifically, the area functions for a two-to-one spheroid and a circular cylinder are calculated and applied to a filtered backprojection algorithm of X-ray CT to obtain the vertical thickness function images. These images are then compared with the true vertical thickness functions of the targets based on their geometry. With theoretical data, this method was found to work very well. Even when experimental data containing creeping waves were used, the method produced satisfactory results for objects with continuously smooth surface.     

An Insight View on Synthetic Protocol,Surface Activity,and Biological Aspects of Novel Biocompatible Quaternary Ammonium Cationic Gemini Surfactants

In this study, we prepared a novel series of diester-functionalized cationic gemini surfactants (C_m-E2O2-C_m) containing ethylene oxide as a spacer with varying alkyl chain lengths and characterized by ¹H NMR, FT-IR, elemental analysis, and ESI-MS. The physicochemical properties of the geminis were explored by tensiometry, fluorescence, dye solubilization, and Krafft point. These geminis acquire superior surface activity than the conventional surfactants. Fluorescence spectroscopy analysis affirmed that the micropolarity and aggregation number of micelles diminished with increase in the alkyl chain length. These geminis represent a new group of amphiphiles of considerably high biodegradability, better cleavability, and low toxicity as assessed by BOD test, FT-IR analysis, and HC₅₀ analysis, respectively. They also showed significant level of antimicrobial activity toward some specified bacterial strains of Gram-positive and Gram-negative by using agar well diffusion method. Furthermore, the thermogravimetric analysis provided information regarding thermal stabilities of the newly synthesized gemini surfactants.     

Design and simulation of a novel metallic microgripper using vibration to release nano objects actively

In this study, we investigate a novel metallic microgripper which is able to grasp and transport nano particles (nano tubes/wires) and release them on desirable substrate by vibrating the gripper arms. This microgripper consists of a chevron actuator to grip nano object electrothermally and interdigited comb drive systems to generate vibration at the gripper arms electrostatically. Metallic (nickel) properties enable the chevron actuator to close the gap and pick the nano particle at low voltage and temperature. In order to reduce the out of plane bending during operation and also increase the gripping force, thickness of the nickel layer must be increased, hence electroplating process is proposed for deposition of nickel layer. To generate vibration at the end effectors, comb drive systems are stimulated by applying two voltage signals at desired resonant frequency to the stators. Practically, by sweeping the frequency of these signals around the resonant frequency the end effectors start vibrating. The vibration results in overcoming the adhesion forces due to inertial effects.     

Support vector regression methodology for prediction of input displacement of adaptive compliant robotic gripper

The prerequisite for new versatile grippers is the capability to locate and perceive protests in their surroundings. It is realized that automated controllers are profoundly nonlinear frameworks, and a faultless numerical model is hard to get, in this way making it troublesome to control utilizing tried and true procedure. Here, a design of an adaptive compliant gripper is presented. This design of the gripper has embedded sensors as part of its structure. The use of embedded sensors in a robot gripper gives the control system the ability to control input displacement of the gripper and to recognize specific shapes of the grasping objects. Since the conventional control strategy is a very challenging task, soft computing based controllers are considered as potential candidates for such an application. In this study, the polynomial and radial basis function (RBF) are applied as the kernel function of Support Vector Regression (SVR) to estimate and predict optimal inputs displacement of the gripper according to experimental tests and shapes of grasping objects. Instead of minimizing the observed training error, SVR _poly and SVR _rbf attempt to minimize the generalization error bound so as to achieve generalized performance. The experimental results show that an improvement in predictive accuracy and capability of generalization can be achieved by the SVR approach compared to other soft computing methodology.