Dense and core-rim structured B4C-TiB2 ceramics with Mo-Co-WC additive

B₄C-TiB₂ ceramics (TiB₂ ranging 5~70 vol%) with Mo-Co-WC as the sintering additive were prepared by spark plasma sintering. In comparison with B₄C-TiB₂ without additive, the enhanced densification was evident in the sintered specimen with Mo-Co-WC additive. Core-rim structured grain was observed around TiB₂ grains. The interface of the rim between TiB₂ and B₄C phases demonstrated different feature: the inner borderline of the rim exhibited a smooth feature, whereas a sharp curved grain boundary was observed between the rim and the B₄C grain. The formation mechanism is discussed: the epitaxial growth of (Ti,Mo,W)B₂ rim around the TiB₂ core may occur as a result of the solid solution and dissolution-precipitation between TiB₂ phase and the sintering additive. It was revealed that the fracture toughness increased as the content of TiB₂ content increased, alongside the decreased hardness. B₄C-30 vol% TiB₂ specimen demonstrated the optimal combination of mechanical properties, reaching Vickers hardness of 24.3 GPa and fracture toughness of 3.33 MPa·m^1/2.     

Mechanical Properties of Single-Layer Diamond Reinforced Poly(vinyl alcohol) Nanocomposites through Atomistic Simulation

Low-dimensional carbon nanostructures are ideal nanofillers to reinforce the mechanical performance of polymer nanocomposites due to their excellent mechanical properties. Through molecular dynamics simulations, the mechanical performance of poly(vinyl alchohol) (PVA) nanocomposites reinforced with a single-layer diamond – diamane is investigated. It is found the PVA/diamane exhibits similar interfacial strengths and pull-out characteristics with the PVA/bilayer-graphene counterpart. Specifically, when the nanofiller is fully embedded in the nanocomposite, it is unable to deform simultaneously with the PVA matrix due to the weak interfacial load transfer efficiency, thus the enhancement effect is not significant. In comparison, diamane can effectively promote the tensile properties of the nanocomposite when it has a laminated structure as it deforms simultaneously with the matrix. With this configuration, the interlayer sp³ bonds endows diamane with a much higher resistance under compression and shear tests, thus the nanocomposite can reach very high compressive and shear stress. Overall, enhancement on the mechanical interlocking at the interface as triggered by surface functionalization is only effective for the fully embedded nanofiller. This work provides a fundamental understanding of the mechanical properties of PVA nanocomposites reinforced by diamane, which can shed lights on the design and preparation of next generation high-performance nanocomposites.     

A practical reliability assessment approach and its application for pile-stabilized slopes using FORM and support vector machine

Bulletin of Engineering Geology and the Environment - Many uncertainties exist in pile-stabilized slopes which make their design substantially complicated. In this paper, a first-order reliability...     

5-二茂铁基噁唑的合成研究

以二茂铁甲醛和对甲苯磺酰基异氰(TOSMIC)为原料,经过Van Leusen反应,一步合成目标化合物5-二茂铁基噁唑,通过~1HNMR、~(13)CNMR和ESI-MS对其结构进行表征,并对影响收率的主要因素进行考察。结果表明,在物料比n(TOSMIC)∶n(二茂铁甲醛)为1.1∶1、反应溶剂为甲醇、K_2CO_3用量即n(K_2CO_3)∶n(二茂铁甲醛)为2.0∶1、反应温度为65℃、反应时间为8 h的最佳条件下,目标化合物收率达到74.7%。该方法具有原料廉价易得、反应操作简单、收率高等优点,具有一定的应用价值。     

一种新的解映射算法的推导和实现

本文在一种16QAM,64QAM,256QAM的解映射算法启发下,提出了新的适合32QAM和128QAM的解映射算法,并在此基础上,给出了适合DVB-C接收机的多QAM解映射结构.然后在FPGA中实现和仿真.最后通过比较说明,相对于传统的查找表解映射方法,提出的解映射算法可以明显减少资源使用率.     

泥页岩井壁稳定研究及在临盘地区的应用

从岩石力学和物理化学两个主要因素简要分析了井壁失稳的机理，指出泥页岩井壁失稳是由力学与化学两方面因素共同作用的结果。钻井液与泥页岩存在化学势差，并改变了井壁附近的孔隙压力，降低岩石强度。借助于井壁处有效应力的变化,将泥页岩与钻井液相互作用时页岩水化所产生的力学效应与纯力学效应结合起来，计算出任意井斜方位井眼围岩应力状态，利用测井资料求出有关岩石力学参数和Mohr Couloumb准则，计算得出防塌的临界钻井液密度。     

9,10-二氰蒽合成方法的改进

以蒽为原料,经溴化和氰化两步合成了光敏剂9,10-二氰蒽(DCA)。从反应溶剂的选择及提纯方法等方面改进了DCA的合成方法,提高了溴化和氰化反应的收率。结果表明,溴化反应时,控制溴的滴加温度为30℃,收率可达95%;合成DCA时,采用连续抽提法提纯,以DMSO为溶剂,反应中生成的无机盐完全溶解,粗产物不经抽提DCA收率可达74%～75%;而选用N-甲基吡咯烷酮为溶剂,DCA可与溴化铜形成配合物CuBr_2·DCA·CuBr_2,此配合物加热易分解,DCA收率达到93%。