以辉锑矿为原料放电等离子烧结快速制备黝铜矿Cu_(12)Sb_4S_(13)及反应机理

采用辉锑矿为原料成功制备出Cu_(12)Sb_4S_(13)块体。研究以Sb_2S_3矿物为原料时烧结工艺对Cu_(12)Sb_4S_(13)合成的影响。在400 ～ 440℃温度区间内均可快速合成Cu_(12)Sb_4S_(13)块体且二次烧结能够进一步减小中间相CuSbS_2和Cu_3SbS_3。第二相Cu_3SbS_4和残留相CuS随着烧结时间的延长而降低。二次烧结前进行机械化球磨处理,干磨比湿磨更容易减小残留相。初次烧结块体的断面SEM和EDS能谱分析表明内部存在Cu或Cu_2S颗粒团聚现象。适当降低Cu或CuS摩尔量(化学计量比0.1 mol)能促进烧结块表面反应进行。烧结过程中,硫磺蒸汽压的导致烧结块表面成分和内部粉末的成分不同。     

Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.     

A flow simulation for the epoxy casting process using a 3D finite‐element method

A three‐dimensional flow simulation for epoxy casting has been developed. A control‐volume‐based finite‐element method is employed, containing a conservative upwind formulation for the advection terms and equal order interpolations for all variables. This simulation predicts the non‐isothermal and reactive flow behavior under the gravity. The viscosity and reaction‐rate parameters were estimated by using a dynamic rheometer and a differential scanning calorimeter. The predicted flow front advancement and temperature profiles in the calculation domain similar to the mold cavity were in close agreement with the corresponding experimental results. The variation of epoxy surface configuration with flow rate also showed the same tendency between the prediction and the experiment. This simulation seems to be applicable not only to the epoxy casting, but also to other molding processes of various thermoset resins. POLYM. ENG. SCI. 45:364–374, 2005. © 2005 Society of Plastics Engineers.     

MyoD and Myf-5 differentially regulate the development of limb versus trunk skeletal muscle

The myogenic progenitors of epaxial (paraspinal and intercostal) and hypaxial (limb and abdominal wall) musculature are believed to originate in dorsal-medial and ventral-lateral domains, respectively, of the developing somite. To investigate the hypothesis that Myf-5 and MyoD have different roles in the development of epaxial and hypaxial musculature, we further characterized myogenesis in Myf-5- and MyoD-deficient embryos by several approaches. We examined expression of a MyoD-lacZ transgene in Myf-5 and MyoD mutant embryos to characterize the temporal-spatial patterns of myogenesis in mutant embryos. In addition, we performed immunohistochemistry on sectioned Myf-5 and MyoD mutant embryos with antibodies reactive with desmin, nestin, myosin heavy chain, sarcomeric actin, Myf-5, MyoD and myogenin. While MyoD(-/-) embryos displayed normal development of paraspinal and intercostal muscles in the body proper, muscle development in limb buds and brachial arches was delayed by about 2.5 days. By contrast, Myf-5(-/-) embryos displayed normal muscle development in limb buds and brachial arches, and markedly delayed development of paraspinal and intercostal muscles. Although MyoD mutant embryos exhibited delayed development of limb musculature, normal migration of Pax-3-expressing cells into the limb buds and normal subsequent induction of Myf-5 in myogenic precursors was observed. These results suggest that Myf-5 expression in the limb is insufficient for the normal progression of myogenic development. Taken together, these observations strongly support the hypothesis that Myf-5 and MyoD play unique roles in the development of epaxial and hypaxial muscle, respectively.     

Two geometrical isomers of linoleic acid: Improved total syntheses

The total syntheses of 9(Z),12(E)- and 9(E),12(Z)-octadecadienoic acids have been carried out. A useful intermediate in both syntheses, 8-bromo-octanoic acid, recently has become available from commercial sources. This compound has been used to expedite the preparation of these isomers. The remaining carbon atoms were derived from propargyl alcohol along with either 1-heptyne or acetylene and 1-bromopentane. Because the overall yield for each sequence was roughly 15% and there were no extraordinary reaction conditions in any of the synthetic steps, the compounds could be prepared readily in multiple gram quantities. The syntheses of the two compounds were supported by data from a variety of spectroscopic techniques.     

Effects of macrophage colony-stimulating factor (M-CSF) on lipopolysaccharide (LPS)-induced mediator production from monocytes in vitro

M-CSF is a macrophage-lineage-specific growth factor that causes proliferation and differentiation of progenitor cells in the bone marrow. To investigate the effects of M-CSF on more matured cells, human monocytes were cultured in the presence or absence of M-CSF for 6 days. Addition of M-CSF at more than 10(2) U/ml resulted in higher viability and caused morphological differentiation to large macrophage-like cells. LPS-induced mediator production was also compared between M-CSF-treated and control cell. Monocytes were incubated with or without M-CSF for 3 days, and were stimulated with 1 microgram/ml of LPS for 2 days. IL-1 beta was not detected in the both culture supernatants, and PGE2 production was not influenced by M-CSF. However, amounts of G-CSF, GM-CSF, IL-6, and TNF-alpha produced in response to 1 microgram/ml of LPS were 1.5 to 2 times greater from monocytes treated with 10(4) U/ml of M-CSF than from control cells. The priming effect of M-CSF on LPS-induced cytokine production was found to require 3-day preincubation, and reached a maximum at the concentration of 10(4) U/ml. M-CSF-treated cells responded to a 10 times lower concentration of LPS than control cells in terms of cytokine production. M-CSF was also shown by flowcytometric analysis to influence the expression of CD14, a receptor for LPS, which might render monocytes more sensitive to LPS.     

Distribution of higher-order structures in injection-molded polypropylenes

Flexural test specimens were injection-molded from six homoisotactic polypropylenes with MFI = 0.49-25.1 dg/min under cylinder temperatures of 200-320°C. Distributions in the flow direction of higher-order structures such as crystallinity X_c, thickness of skin layer, a*-axis-oriented component fraction [A*], and crystalline orientation functions and distributions in the thickness direction of higher-order structures such as X_c, β-crystal contents, [A*], and crystalline orientation functions were studied. These higher-order structures are inhomogeneous in the flow and thickness directions, which strongly influences the product properties such as mechanical and thermal properties. Molecular orientation process in injection molding was theoretically analyzed from a viewpoint of growth of recoverable shear strain at the gate and its relaxation in the cavity, which could considerably well explain the variations in the flow and thickness directions of the quantities such as thickness of the skin layer and crystalline orientation functions which express the degree of molecular orientation.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.