Morphological investigations of a textured black copper selective coating

The microstructural investigations of a textured black copper selective coating are reported. These surfaces possess remarkably high initial absorptance 0.97 to 0.98 and emittance ₁₀₀ 0.2 ± 0.02. These surfaces reveal a new sponge-like, porous, layered microstructure. They are made of loosely packed long and fine grains which appear randomly distributed. The copper grains are dispersed in a semiconductor oxide matrix. The spacing between these grains is of the order of solar wavelength. Also, these surfaces possess opulent solar selectivity and structural stability up to 250° C in air and under vacuum conditions.     

Distributed Dynamic Backhauling in Aerial Heterogeneous Networks

Wireless Personal Communications - A Wireless Mesh Network (WMN) is a multi-hop network that gains the benefits of low deployment cost, fast access speed, expanded service coverage and large...     

Exploring relationships between satiation,perceived satiety and plant-based snack food features

We aimed to identify relations between satiation and subsequent satiety for six plant-based foods (apple, avocado, banana, carrot, chick pea and macadamia) using a panel of ten healthy participants and a complete crossover randomised design. Food was served as a mid-morning snack ad libitum over 20 min until participants were comfortably full, and subsequent satiety was monitored for up to 180 min. Carrot and macadamia had significantly higher perceived fullness during eating, but also significantly lower perceived satiety per gram than other foods. Food energy factors had no strong relationship with perceived fullness, but were significantly positively correlated with satiety. Mastication number had significant effects on both perceived fullness (negative) and satiety (positive). This pilot study showed that plant food factors affecting perceived fullness during eating and subsequent satiety are different, and suggests how portion control through satiation for different plant-based snacks may influence both energy intake and subsequent satiety.     

Kinetic analysis of bile salt passage across a dialysis membrane in the presence of cereal soluble dietary fibre polymers

The kinetics of passage of a model bile salt and complete porcine bile across a dialysis membrane, in the presence and absence of two cereal-derived soluble dietary fibre polysaccharides, were studied as a model for passage across the unstirred water layer that lines the small intestine. A first-order kinetic analysis allowed rate coefficients to be derived which quantified the effectiveness of barley mixed linkage β-glucan and wheat arabinoxylan in retarding the transport of bile. For both, a model bile salt and complete porcine bile, rate coefficients decreased with both concentration and viscosity. A combination of viscosity and molecular interaction effects is suggested to control the effect of the two polysaccharides on the transport of bile.     

Quick and reliable estimation of BOD load of beverage industrial wastewater by developing BOD biosensor

An amperometric biosensor for determination of biochemical oxygen demand in wastewater has been developed to overcome the time consuming monitoring procedures. The performance and stability of the immobilized membrane have been investigated at 37 °C and pH 6.8. Immobilized microbial membranes maintain their stability and activity after intermittent use for 400 cycles when stored at 4 °C in sodium phosphate buffer pH 6.8. The response time of the BOD sensor was only 90 min, being independent of the concentration, and the lower detection limit was 1 mg/l. The obtained BOD values showed correlation with that of the conventional method for BOD determination (BOD5) with a deviation of ±10%. Moreover, the sensor exhibits good repeatability (3.39–4.45%) and reproducibility (1.85–2.25%). Software was added to upgrade this sensor and to make it a promising candidate for online monitoring.     

Textured black brass spectrally selective coating

A textured black brass selective coating has been reported in this paper. These textured black brass selective coatings have been obtained by using chemical conversion process. They exhibit initial solar absorptance ()0.96 and thermal emittance ₁₀₀0.17 and are reproducible. These have been annealed up to 250°C in air and at 150°C in vacuum (10⁻³ Torr) possessing solar absorptance ()0.90. TEM, XRD and FTIR analyses have also been reported which suggests that the coating consists of multi-phases.     

Review on nano-and microfiller-based polyamide 6 hybrid composite: Effect on mechanical properties and morphology

Polyamide 6 (PA6)-based composites are of evolving interest due to its high strength, wear resistance, and barrier properties. The use of binary composites mostly with nanomaterial and glass fibers has been reviewed and presented in literature. However to obtain a balance of properties like stiffness, toughness, and strength along with cost reduction, ternary composites of PA6 have been designed. To achieve the balance, PA6 blend-based composites, with combination of microfiller/nanofiller or PA6 with combination micro-microfiller, PA6 with microfiller/nanofiller and fiber have been designed. The properties of PA6-based ternary hybrid composites depend on type of dispersed phase used, presence of compatibilizer, type of filler used (nanofiller or microfiller or fiber or hybrid) and combination of fillers used. However, a review in this direction is not available in literature. Here, in this study, an overall understanding of various fillers, dispersed phase, and their combinations can be understood along with the discussion on effect of these on tensile properties and morphology of hybrid composite. In this study, an attempt has been made to review the various fillers and dispersed phase and their combinations which have been used in designing the PA6 hybrid composite with good balance of stiffness, toughness, and strength.     

Bright Aggregation‐Induced Emission Dots for Dynamic Tracking and Grading of Patient‐Derived Xenografts in Zebrafish

Cancer prognosis will benefit from a scoring system that could grade malignant traits of patient‐derived cells by assessing their growth and metastasis in a living system. Specific tracking of patient‐derived cells requires labeling by contrast agents with good signal‐to‐noise ratio and no specific stain of host tissues. Towards this aim, aggregation‐induced emission (AIE) dots are developed for in vivo cancer tracking with emphasis on reproducible optimized formulation and specific fluorescent labeling of cells that enable enhanced spatial temporal resolution in vivo. The importance of energy‐dependent AIE dots uptake for patient‐derived cell labeling is emphasized to reveal their specific uptake by viable cancer cells. Using optically transparent zebrafish embryo, the ability is demonstrated to follow the engraftment of transplanted AIE dot labeled cells in zebrafish brains over one week. Cells detected outside the brain after 7 d are quantified as metastatic cells. Results from seven clinical samples demonstrate the utility of this methodology to differentiate low engraftment level of benign neoplasms from higher engraftment level and metastasis detected in malignant ovarian cancer specimens. Achieving clinically validated results supports the use of AIE dot labeled patient derived cells in zebrafish xenografts for future cancer prognosis.     

Application of moisture activated dry granulation (MADG) process to develop high dose immediate release (IR) formulations

Moisture activated dry granulation (MADG) method was used to develop IR tablets with cohesive, fluffy and high dose drugs. To evaluate this approach, three drugs: metformin hydrochloride, acetaminophen and ferrous ascorbate were selected as model compound along with three binders: maltodextrin DE16, PVP K 12 and HPC. The granules were generated using MADG method and tablets were prepared using rotary tablet press. The granules and tablets were characterized for particle size analysis, flow properties, tablet hardness, friability, moisture content, dissolution study, disintegration time and stability study. All results were found to be within acceptable limits. Development of all formulation tablets were found as best fitted for an immediate release of Metformin hydrochloride, acetaminophen and ferrous ascorbate. MADG delivered a robust manufacturing process for generation of granules with excellent flowability. The tablets prepared using this method were found to show better content uniformity, good compactability and low friability. Use of this approach aids to lower the amount of excipients used to overcome physiochemical limitation of the drug substances and there side effects. Both drying and milling steps in wet granulation were not required for MADG process. MADG became a cost effective process which could lead to reduced total tablet size and also save time.     

A Backdrop Case Study of AI-Drones in Indian Demographic Characteristics Emphasizing the Role of AI in Global Cities Digitalization

The automatic identification of the modulation format of a detected signal is a major task of an intelligent receiver in both military and civilian applications. It is well known that the maximum likelihood (ML) classifier requires a priori knowledge of the incoming signal and channel (including amplitude, timing information, noise power, and the roll-off factor of the pulse-shaping filter). To relax this requirement, we introduce a novel estimator to estimate the parameters required by the ML classifier which is blind to the modulation scheme of the received signal, and this gives rise to a new blind modulation classifier for digital amplitude-phase modulated signals. While the proposed classifier is completely blind, the simulation results show that the performance of this classifier is very close to the optimal non-blind classifier.