Influence of dry operating conditions: observation of oscillations and low temperature CO oxidation over Co3O4 and Au/Co3O4 catalysts

A Sm(III) exchanged NaY zeolite prepared from aqueous SmCl₃ was modified with various amounts of fluorine using NH₄F. These fluorinated zeolites exhibit enhanced catalytic activity for the dealkylation of cumene. The evaluation of acid sites by infrared spectroscopy and pyridine adsorption was correlated with fluorine content.     

Threshold for Millimeter-Wave (60 GHz)-Induced Ocular Injury

Journal of Infrared, Millimeter, and Terahertz Waves - Millimeter waves (MMW) absorbed by skin or cornea may induce damage by heat. We have developed a 60 GHz MMW exposure-induced eye...     

A molecular dynamics study of bubble nucleation in liquid oxygen with impurities

The present study investigates bubble nucleation in liquid oxygen with dissolved impurities (nitrogen or helium molecules) using molecular dynamics simulations. When the mole fraction of impurities is 0.05, there is a fundamental difference in the bubble nucleation mechanism between the two dissolved impurities cases; vaporization in the homogeneous bulk makes a bubble in the case of a nitrogen‐dissolved liquid while phase separation of impurities and liquid molecules makes a nucleus in the case of a helium‐dissolved liquid. Fluctuations can cause local voids, which in turn can grow to be bubbles, and this effect is stronger in the case of a helium‐dissolved liquid with a lower mole fraction (0.01) than in the case of a nitrogen‐dissolved liquid with a higher mole fraction (0.05). From these results, we conclude that helium molecules have a much stronger action to raise the bubble formation pressure compared with nitrogen. In this paper, the kinetically‐defined critical nucleus, which is a very important factor in quantitatively evaluating the nucleation mechanism, is also estimated through the calculation of the size change rate of each nucleus. © 2005 Wiley Periodicals, Inc. Heat Trans Asian Res, 34(7): 514–526, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20082     

Measurement and correlation of the solid-liquid-gas equilibria for carbon dioxide + normal chain saturated aliphatic hydrocarbon systems

The pressure p-temperature T projections of solid-liquid-gas (S-L-G) three-phase coexistence lines for the carbon dioxide + tetradecanoic acid (C₁₄H₂₈O₂) system, the carbon dioxide + hexadecanoic acid (C₁₆H₃₂O₂) system, and the carbon dioxide + 1-hexadecanol (C₁₆H₃₄O) were measured by the first melting point method in which the initial appearance of the liquid phase was observed. The profiles of the p-T projections of the S-L-G lines for the carbon dioxide + acid systems are similar to each other, the S-L-G equilibria for the carbon dioxide + acid systems are, however, different from that for the carbon dioxide + 1-hexadecanol systems. The experimental p-T projections of the S-L-G lines were also correlated by the Peng-Robinson equation of state and the van der Waals type mixing rules with two binary interaction parameters introduced into attraction term and size terms, respectively. The present model gave good correlation results for all of the experimental S-L-G lines with maximum average absolute relative deviations of 0.075% for the carbon dioxide + tetradecanoic acid system, 0.14% for the carbon dioxide + hexadecanoic acid system and 0.28% for the carbon dioxide + 1-hexadecanol system, respectively.     

Controlling the drug release rate from biocompatible polymers with micro-patterned diamond-like carbon (DLC) coating

During the past year, we have witnessed the evolution of an intense public controversy regarding late thrombosis following implantation of drug eluting stent (DES) in patients with obstructive coronary artery disease. To overcome the problem, DES should possess sufficient biocompatibility and non-thrombogenicity with a controlled drug release system. A new DES composed of biocompatible polymers coated with antithrombogenic diamond-like carbon (DLC) coating was proposed. In this study, the drug release profile of the newly proposed drug eluting system was thoroughly investigated. Three polymers were selected as base drug-reservoir materials: hydrophilic 2-methacryloyloxyethyl phosphorylcholine (MPC), hydrophobic poly (ethylene-co-vinyl acetate) (EVA) and less hydrophobic polyurethane (PU). The three polymers are currently used or studied for biomedical materials, while MPC and DLC were already confirmed as excellent biocompatible materials with antithrombogenicity. After coating the lattice-like patterned DLC on both polymers containing drug, samples were soaked in 2 ml of medium of phosphate-buffered saline with 10% ethanol. The drug release rate was measured by a spectrophotometer. The percentile cover area of patterned DLC on polymers was varied from 0% (without DLC) to 100% (fully covered). The sample without DLC coating presented an initial burst of the drug release from the polymer matrix, whereas the DLC-coated samples inhibited the initial burst release from polymers within the first five days of the experiments. It was found that the drug eluting profiles could be effectively controlled by changing the cover area of micro-patterned DLC coatings on polymers, which may be applicable to the next-generation DES system that eventually prevents late thrombosis.     

Seismic tests of a pile-supported structure in liquefiable sand using large-scale blast excitation

Extensive, large-amplitude vibration tests of a pile-supported structure in a liquefiable sand deposit have been performed at a large-scale mining site. Ground motions from large-scale blasting operations were used as excitation forces for vibration tests. A simple pile-supported structure was constructed in an excavated 3 m-deep pit. The test pit was backfilled with 100% water-saturated clean uniform sand. Accelerations were measured on the pile-supported structure, in the sand in the test pit, and in the adjacent free field. Excess pore water pressures in the test pit and strains of one pile were also measured.Vibration tests were performed with six different levels of input motions. The maximum horizontal acceleration recorded at the adjacent ground surface varied from 20 Gals to 1353 Gals. These alternations of acceleration provided different degrees of liquefaction in the test pit. Sand boiling phenomena were observed in the test pit with larger input motions. This paper outlines vibration tests and investigates the test results.     

Fracture mechanics of diamond-like carbon (DLC) films coated on flexible polymer substrates

Diamond-like carbon (DLC) films have been widely used for many industrial applications due to their outstanding physical properties such as high hardness, wear resistance and biological compatibility. The DLC films coated on polymer substrates have also been extensively used and investigated because recently, quite a few applications for the use of these polymer-DLC composites have been proposed and actively discussed. The applications range from DLC-coated Polyethylene Terephthalate film (DLC-PET), through DLC-coated Polycarbonate (DLC-PC) to other DLC-coated rubbers. In this work, thin DLC films coated on several polymer substrates possessing different chemical structures and Young's moduli were introduced. The DLC-polymer films were stretched to different strains and the extended surface was investigated by optical microscopy and scanning electron microscopy (SEM) to study the fracture mechanics of the DLC-coated polymer films. Horizontally and vertically aligned micro-cracks and micro-buckling were observed, constructing periodic lattice-like fracture patterns on the surface of the extended DLC-polymer films. It was found that the lattice patterns were significantly influenced by Young's moduli of polymer substrates and DLC films, and that the patterns were also dependent on the adhesion between the DLC films and the polymers.     

Half-data-page insertion method for increasing recording density in angular multiplexing holographic memory

We have developed a method to use a half-size data page between two full-size data pages to increase the recording density in angular multiplexing holographic memory up to 1.5× as much as the conventional angular multiplexing sequence. In our recording sequence, the full- and half-size data pages are alternately multiplexed. This is because each plane wave from various points in a data page has different angular selectivity. A half-size data page has higher angular selectivity than a full-size data page. The required angular intervals were estimated by numerical simulation taking holographic medium tilt into account. Also, an angular multiplexing experiment using the half-data-page insertion method resulted in a low bit error rate of the order of 10(-3), which is sufficient for practical use.