Experimental determination of NH<Subscript>4</Subscript>NO<Subscript>3</Subscript>-KNO<Subscript>3</Subscript> binary phase diagram

The solid-state phase transitions in ammonium nitrate (AN)-potassium nitrate (KN) system, and the equilibrium AN-KN phase diagram have been determined by using differential scanning calorimetry and high-temperature in situ x-ray diffractometry. Sample preparation was performed in a special “dry room” with very low humidity. A single phase region (AN III) with no phase transitions to 373 K was observed in the composition range 5 to 20% KN; this is critical for use in air bag gas generators. The high-temperature KN phase (KN I) has a wide range of stability from 20 to 100 wt.% KN. There are one eutectic, two eutectoid, three peritectoid, and one congruent transformations in this phase diagram. Two new nonstoichiometric phases were found at lower temperatures in the mid-composition range between the AN and KN terminal solid solutions. Details of the phase equilibria are presented.     

Analysis and Optimization of Noise in Bipolar RF Harmonic Mixers

A noise analysis of bipolar harmonic mixers (BHM) used for direct-conversion receivers is presented in this paper. Analytical and simulated results for the transfer function of the mixer are presented. Simple analytical expressions describing noise contribution from all sources are derived. Estimation of flicker noise quite agrees with harmonic-balance simulation results. Based on the derived expressions, total time average noise power spectral density (PSD) at the output is compared with simulation results. For the recommended regions of operation, error is less than 20%. The overall BHM noise figure (NF) is calculated and optimized based on a simple extracted formula. Errors introduced by analysis remain within a 1.5-dB margin with respect to simulation results. The validity of analysis for high frequencies is justified. The effect of flicker noise coefficient on the overall mixer NF is compared for different available processes.     

CARD: A Contact-based Architecture for Resource Discovery in Wireless Ad Hoc Networks

Traditional protocols for routing in ad hoc networks attempt to obtain optimal or shortest paths, and in doing so may incur significant route discovery overhead. Such approaches may be appropriate for routing long-lived transfers where the initial cost of route discovery may be amortized over the life of the connection. For short-lived connections, however, such as resource discovery and small transfers, traditional shortest path approaches may be quite inefficient. In this paper we propose a novel architecture, CARD, for resource discovery in large-scale wireless ad hoc networks. Our mechanism is suitable for resource discovery as well as routing very small data transfers or transactions in which the cost of data transfer is much smaller than the cost of route discovery. Our architecture avoids expensive mechanisms such as global flooding and complex hierarchy formation and does not require any location information. In CARD resources within the vicinity of a node, up to a limited number of hops, are discovered using a proactive scheme. For resources beyond the vicinity, each node maintains a few distant nodes called contacts. Contacts help in creating a small world in the network and provide an efficient way to query for distant resources. Using contacts, the network view (or reachability) of the nodes increases, reducing the discovery overhead and increasing the success rate. On the other hand, increasing the number of contacts also increases control overhead. We study such trade-off in depth and present mechanisms for contact selection and maintenance that attempt to increase reachability with reduced overhead. Our schemes adapt gracefully to network dynamics and mobility using soft-state periodic mechanisms to validate and recover paths to contacts. Our simulation results show that CARD is scalable and can be configured to provide desirable performance for various network sizes. Comparisons with other schemes show overhead savings reaching over 93% (vs. flooding) and 80% (vs. bordercasting or zone routing) for high query rates in large-scale networks.     

Rapid real-time generation of super-resolution hyperspectral images through compressive sensing and GPU

Recently, compressive sensing (CS) has offered a new framework whereby a signal can be recovered from a small number of noisy non-adaptive samples. This is now an active area of research in many image-processing applications, especially super-resolution. CS algorithms are widely known to be computationally expensive. This paper studies a real time super-resolution reconstruction method based on the compressive sampling matching pursuit (CoSaMP) algorithm for hyperspectral images. CoSaMP is an iterative compressive sensing method based on the orthogonal matching pursuit (OMP). Multi-spectral images record enormous volumes of data that are required in practical modern remote-sensing applications. A proposed implementation based on the graphical processing unit (GPU) has been developed for CoSaMP using computed unified device architecture (CUDA) and the cuBLAS library. The CoSaMP algorithm is divided into interdependent parts with respect to complexity and potential for parallelization. The proposed implementation is evaluated in terms of reconstruction error for different state-of-the-art super-resolution methods. Various experiments were conducted using real hyperspectral images collected by Earth Observing-1 (EO-1), and experimental results demonstrate the speeding up of the proposed GPU implementation and compare it to the sequential CPU implementation and state-of-the-art techniques. The speeding up of the GPU-based implementation is up to approximately 70 times faster than the corresponding optimized CPU.     

Comparative repeatability of guide-pin axis positioning in computer-assisted and manual femoral head resurfacing arthroplasty

The orientation of the femoral component in hip resurfacing arthroplasty affects the likelihood of loosening and fracture. Computer-assisted surgery has been shown to improve significantly the surgeon's ability to achieve a desired position and orientation; nevertheless, both bias and variability in positioning remain and can potentially be improved. The authors recently developed a computer-assisted surgical (CAS) technique to guide the placement of the pin used in femoral head resurfacing arthroplasty and showed that it produced significantly less variation than a typical manual technique in varus/valgus placement relative to a preoperatively determined surgical plan while taking a comparable amount of time. In the present study, the repeatability of both the CAS and manual techniques is evaluated in order to estimate the relative contributions to overall variability of surgical technique (CAS versus manual), surgeon experience (novice versus experienced), and other sources of variability (e.g. across specimens and across surgeons). This will enable further improvements in the accuracy of CAS techniques. Three residents/fellows new to femoral head resurfacing and three experienced hip arthroplasty surgeons performed 20-30 repetitions of each of the CAS and manual techniques on at least one of four cadaveric femur specimens. The CAS system had markedly better repeatability (1.2 degrees) in varus/valgus placement relative to the manual technique (2.8 degrees), slightly worse repeatability in version (4.4 degrees versus 3.2 degrees), markedly better repeatability in mid-neck placement (0.7 mm versus 2.5 mm), no significant dependence on surgeon skill level (in contrast to the manual technique), and took significantly less time (50 s versus 123 s). Proposed improvements to the version measurement process showed potential for reducing the standard deviation by almost two thirds. This study supports the use of CAS for femoral head resurfacing as it is quicker than the manual technique, independent of surgeon experience, and demonstrates improved repeatability.     

Influence of atmospheric plasma-induced graft polymerization of DADMAC into cotton on dyeing with acid dyes

The primary objective of this work was to generate dyes sites in cotton fiber for acid dyes via free radical graft polymerization of diallyldimethylammonium chloride (DADMAC), to confer cationized cotton, and evaluate the dyeability of the cationized cotton toward acid dyes, which is unprecedented. Plasma-induced graft polymerization of DADMAC on cotton, using different plasma conditions, followed by dyeing with different acid dyes was studied. The color yield of dyed cotton was evaluated using K/S. Light fastness, color change, and staining following accelerated washing cycles were carried out to evaluate the effectiveness of cotton cationization. Cross-section dyed cotton was studied using scanning electron microscopy and showed deep dyeing of acid dyes into cotton fibers. This approach resulted in significant dye uptake into the fibers and considerably reduced the need for effluent treatment.     

Study the Performance of the AC/DC Resistors During Their DC and AC Measurements

Some of traceability chains for the AC resistance measurements are based on AC/DC resistors. In this paper, performance of two types of them with different values has been investigated for their optimum utilization. Tinsley and Cambridge AC/DC resistors have been measured as DC resistors using different measurement methods and as AC resistors at various frequencies. DC direct method using digital reference multimeter is more accurate for the resistance values 1, 10, 100 Ω, and 1 kΩ. For the values 10 and 100 kΩ; measurement results are very near by using the DC direct and ratio methods. At 100 kΩ; representation of the resistance as an equivalent series resistance is not suitable at frequencies above 10 kHz, while for 100 mΩ and 1 Ω; the equivalent parallel representation is not suitable above the same frequency. The uncertainty analysis is also studied for all the obtained results.     

Fully Automated Inductance Measuring System Using New Fabricated Inductance Box

Decade inductance boxes are widely used in electrical laboratories for calibration of instruments that measure inductance. The main aim of this paper is to construct a new inductance box providing a huge number of automated inductance steps, which are used in the laboratories to perform full automatic calibration of inductance meters. Therefore, a new inductance box has been introduced that mainly consists of three decades. The three inductance decades have the same design, but each has its four different internal inductive elements. Each decade can generate 15 different inductance values, so it is more economical and practical compared to the other ordinary decades, which produce only 10 values by using 10 internal inductive elements. 1666 different inductance values can be obtained from this inductance box, while 4096 inductance values can be obtained by the possible combinations of its three decades steps. Practical design, fabrication and specifications of this new inductance box are demonstrated in detail. It is designed to achieve relative accuracy in the range from 5 × 10^?4 to 5 × 10^?3. It could be used to perform full automatic inductance measurements at the National Institute of Standards, Egypt, for the first time. Comparison between an ordinary inductance box and the new introduced one has been made to validate its performance.     

Characterization and quantitation of aprepitant drug substance polymorphs by attenuated total reflectance fourier transform infrared spectroscopy

In this study, we report the use of attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FT-IR) for the identification and quantitation of two polymorphs of Aprepitant, a substance P antagonist for chemotherapy-induced emesis. Mixtures of the polymorph pair were prepared by weight and ATR-FT-IR spectra of the powdered samples were obtained over the wavelength range of 700-1500 cm(-1). Significant spectral differences between the two polymorphs at 1140 cm(-1) show that ATR-FT-IR can provide definitive identification of the polymorphs. To investigate the feasibility of ATR-FT-IR for quantitation of polymorphic forms of Aprepitant, a calibration plot was constructed with known mixtures of the two polymorphs by plotting the peak ratio of the second derivative of absorbance spectra against the weight percent of form II in the polymorphic mixture. Using this novel approach, 3 wt % of one crystal form could be detected in mixtures of the two polymorphs. The accuracy of ATR-FT-IR in determining polymorph purity of the drug substance was tested by comparing the results with those obtained by X-ray powder diffractometry (XRPD). Indeed, polymorphic purity results obtained by ATR-FT-IR were found to be in good agreement with the predictions made by XRPD and compared favorably with actual values in the known mixtures. The present study clearly demonstrates the potential of ATR-FT-IR as a quick, easy, and inexpensive alternative to XRPD for the determination of polymorphic identity and purity of solid drug substances. The technique is ideally suited for polymorph analysis, because it is precise, accurate, and requires minimal sample preparation.     

Construction and remote calibration of an automated resistance measuring system

The calibration of resistances was being performed manually at National Institute of Standards (NIS), Egypt till now. In this paper, a fully automated system for the remote calibrations of resistances is described. This sytem is mainly used for routine calibrations for low precision calibrations. The calibration of many resistors can be performed in this system automatically through the Resistors Automatic Changer which is controlled by a LabVIEW program developed and described in the present research work. Not only these calibrations of resistances are performed automatically but are also controlled remotely via an internet connection. Some simple remote and automated resistance measurements are carried out just to confirm our new measuring system.