The Radical Versus Non-radical Reactive Intermediates in the Iron(III) Porphyrin Catalyzed Oxidation Reactions by Hydroperoxides, Hydrogen Peroxide and Iodosylarene

In the catalytic reaction of an iron(III) porphyrin with t-BuOOH, CumOOH, H₂O₂ and C₆F₅IO, cyclohexene was used as a probe substrate. The selective hydroxylation of cyclohexene by hydroperoxides proceeds through radical path and this has been utilized for successful dioxygen activation/autooxidation. For other oxidants epoxide was the major product and the reactions proceed through non-radical path.     

Micro-stress distribution within polycrystalline aggregate

Summary The three-dimensional Poisson-Voronoi model, which is topologically equivalent to the microstructure of real ceramics and metals, has been used to study the stress distribution within a simulated polycrystalline aggregate having 200 grains. Micro-stresses such as the maximum principal stress, maximum shear stress, first invariant of stress, and Von-Mises stress are found to vary systematically with the anisotropy of single crystal.     

Oxygen-enrichment of YBa2Cu3 YBa2Cu3O7-δ using the fluidization techniqueusing the fluidization technique

The oxygen-deficient phase of the highT _c superconductor, YBa₂Cu₃O₇, was oxygen-enriched using the fluidization technique to give good superconducting properties. The normal method of oxygen treatment at 900°C for 24 h and at 600°C for 24 h has been reduced to just one treatment at 600°C for 12 h by the fluidization technique to achieve almost the same strength of superconducting signal for the YBa₂Cu₃O₇ powder, which establishes the attractiveness of the latter route for the large-scale preparation of superconducting material. The particle sizes were in the range 0–90, 90–180 and 180–420 μm. The fluidized particles were crystalline with orthorhombic distortion.T _c ^onset , estimated using the a.c. magnetic susceptibility method, was 91·3 K. The volume fraction of superconducting material in the product was 83·7–85·3%, one of the highest values reported so far for YBa₂Cu₃O₇.     

Oxidation Behavior of Rh–30Ni–18Nb Refractory Superalloy

The isothermal-oxidation behavior of Rh–30Ni–18Nb refractory alloy was investigated up to a period of 312 hours in air from 1000 to 1350°C. A comparison of the oxidation behavior of this alloy with a conventional Ni-base superalloy (Inconel 713 C) shows an order-of-magnitude higher oxidation resistance. This experimental alloy oxidizes by forming alternate layers of Nb₂O₅ and RhO while NiO is on the surface in contact with air. Optical and scanning-electron microscopy (SEM) was used to study the microstructure and morphology for the characterization of the oxides. Thermal stability of the alloy for extended periods of exposure to air at 1400°C was studied using transmission-electron microscopy (TEM).     

Inkjet-printed patch antenna emitter for wireless communication application

This research focuses on exploring low-cost and rapid production solutions for fabricating emitters for patch antennas for wireless communication applications. Additive manufacturing technique is employed to fabricate two patch antennas using silver nanoparticle ink on FR4 substrate. Finite-element simulation software, HFSS is used to analyse and predict the theoretical performance of the antenna designs for 2.4?GHz MIMO and 6?GHz wireless data transmission. The fabricated antennas have resonant frequencies closely matching the design values. The work provides a viable solution for fabricating emitters and finally antennas commercially using inkjet printing platform, thus overall reducing the cost and simplifying the process.     

Lattice and grain boundary diffusion of cerium and neodymium in nickel

Diffusion of cerium and neodymium in nickel has been studied by the serial sectioning technique using radioactive tracers¹⁴¹Ce and¹⁴⁷Nd, in the temperature ranges 700° to 1100°C for volume and 500° to 875°C for grain boundary diffusion respectively. Volume diffusivities can be expressed as: $$\begin{gathered} D_{Ce/Ni} = (0.66 \pm 0.18)\exp \left( { - \frac{{60,800 \pm 810}}{{RT}}} \right)cm^2 /\sec \hfill \\ D_{Nd/Ni} = (0.44 \pm 0.13)\exp \left( { - \frac{{59,820 \pm 830}}{{RT}}} \right)cm^2 /\sec \hfill \\ \end{gathered} $$ and grain boundary diffusivities by: $$\begin{gathered} Dg_{Ce/Ni} = 0.11\exp \left( { - \frac{{29,550}}{{RT}}} \right)cm^2 /\sec \hfill \\ Dg_{Nd/Ni} = 0.07\exp \left( { - \frac{{28,580}}{{RT}}} \right)cm^2 /\sec \hfill \\ \end{gathered} $$ Results of volume diffusion have been compared with those calculated from the theories of diffusion based on size and charge difference between the solute and the solvent atoms. Whipple and Suzuoka methods have been used to evaluate the grain boundary diffusion coefficients. Both the methods give similar results.     

Studies on the development of aluminium alloy–mild steel reinforced composite

With a view to developing a new metal–metal cast composite material as a possible substitute for ferrous materials in wear resistant applications, Al alloy (LM11) is reinforced with mild steel (ms) wires and it is heat treated to get ‘reaction interface’ (RI). Microhardness, tensile properties and wear characteristics of the matrix, as-cast and heat treated composites have been determined. While microhardness of the composite showed variation from 150 to 45 VHN across the interface in the as-cast composite, annealed (500–525°C) composite showed a microhardness of 350–420 VHN at the interface indicating the effectiveness of the heat treatment. It is seen that the % improvement in wear resistance increased with increase in number of wires when embedded in the aluminium alloy matrix. Further imrpovement of about 30% was observed when heat treated at 500°C for 15 h. These results have been discussed in terms of wetting between ms wires and the matrix, particularly the increase of hardness and tensile strength to the formation of ‘reaction interface’ due to annealing. The width of the interface increased with annealing time and temperature and the kinetics of reaction followed logarithmic and parabolic growth rate. The activation energy for the formation of intermetallics constituting the reaction interface is found to be 20.7 KJ mol⁻¹. From the measured hardness and ultimate tensile strength of the constituents and composites an empirical relation was deduced.     

Characterization of carbon fabric coated with Ni-P and Ni-P-ZrO2-Al2O3 by electroless technique

Ni-P and Ni-P-ZrO₂-Al₂O₃ (Ni-P-X) composite coatings on carbon fiber woven fabric have been attempted by electroless (EL) coating technique. For producing Ni-P EL coating, a sodium hypophosphite is used as reducing agent in alkaline bath whereas for producing composite coating, in the same bath, the co-precipitation of Al₂O₃ along with ZrO₂ by a chemical reaction has been used. The bath used was maintained at pH value of 9 ± 0.25 and a temperature of 90 ± 2°C for all the coatings under investigation. The morphology of coatings has been studied under SEM and the phases have been identified by XRD and TEM. The phases like microcrystalline nickel, amorphous nickel, Ni₅P₄ and Ni₁₂P₅ have been identified to be present. The grain size of these phases has been seen to be in the range of 5–10 nm. The tensile strength of as-coated and heat treated samples of both the types of coatings have been compared with that of uncoated fabric. The UTS values of uncoated carbon fabric used has been found to 3.7 N/mm² whereas that for heat treated after coating the fabric samples with Ni-P and Ni-P-ZrO₂-Al₂O₃ EL coatings have been observed to be 11.1 and 12.4 N/mm² respectively.