Demonstration of a tool for automatic learning and re-use of knowledge in the activated sludge process.

Wastewater treatment plant operators encounter complex operational problems related to the activated sludge process and usually respond to these by applying their own intuition and by taking advantage of what they have learnt from past experiences of similar problems. However, previous process experiences are not easy to integrate in numerical control, and new tools must be developed to enable re-use of plant operating experience. The aim of this paper is to investigate the usefulness of a case-based reasoning (CBR) approach to apply learning and re-use of knowledge gained during past incidents to confront actual complex problems through the IWA/COST Benchmark protocol. A case study shows that the proposed CBR system achieves a significant improvement of the benchmark plant performance when facing a high-flow event disturbance.     

Benchmark simulation Model no 2 in Matlab-simulink: towards plant-wide WWTP control strategy evaluation.

In this paper, implementation of the Benchmark Simulation Model No 2 (BSM2) within Matlab-Simulink is presented. The BSM2 is developed for plant-wide WWTP control strategy evaluation on a long-term basis. It consists of a pre-treatment process, an activated sludge process and sludge treatment processes. Extended evaluation criteria are proposed for plant-wide control strategy assessment. Default open-loop and closed-loop strategies are also proposed to be used as references with which to compare other control strategies. Simulations indicate that the BM2 is an appropriate tool for plant-wide control strategy evaluation.     

WWTP dynamic disturbance modelling--an essential module for long-term benchmarking development.

Intensive use of the benchmark simulation model No. 1 (BSM1), a protocol for objective comparison of the effectiveness of control strategies in biological nitrogen removal activated sludge plants, has also revealed a number of limitations. Preliminary definitions of the long-term benchmark simulation model No. 1 (BSM1_LT) and the benchmark simulation model No. 2 (BSM2) have been made to extend BSM1 for evaluation of process monitoring methods and plant-wide control strategies, respectively. Influent-related disturbances for BSM1_LT/BSM2 are to be generated with a model, and this paper provides a general overview of the modelling methods used. Typical influent dynamic phenomena generated with the BSM1_LT/BSM2 influent disturbance model, including diurnal, weekend, seasonal and holiday effects, as well as rainfall, are illustrated with simulation results. As a result of the work described in this paper, a proposed influent model/file has been released to the benchmark developers for evaluation purposes. Pending this evaluation, a final BSM1_LT/BSM2 influent disturbance model definition is foreseen. Preliminary simulations with dynamic influent data generated by the influent disturbance model indicate that default BSM1 activated sludge plant control strategies will need extensions for BSM1_LT/BSM2 to efficiently handle 1 year of influent dynamics.     

光掩膜技术瞄准市场需求

在光掩膜领域,我们清楚地看到显示器市场和半导体市场的快速增长。与此同时电子封装市场也在不断地激励着技术革新。显示器市场平面显示器已广泛用于笔记本电脑、移动电话和电脑显示器等产品,而平面电视更成为生产设施投资的主要动力．以达到以更低的生产成本制造更大尺寸基板的目的。     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.     

Trams-a risk factor for pedestrians

In Gothenburg tram injuries were identified to be an important cause of traffic injuries and fatalities (48%) among pedestrians. During the summer middle-aged men, often under the influence of alcohol, were often severely injured and the injury rate was also high during the autumn. A majority (60%) of those fatally injured were under the influence of alcohol. Most injury events happened at or near a tram stop. The most serious injuries arose when the victim landed under a tram. In 1992, a runaway tram caused a major disaster, killing 10 pedestrians and injuring 30. The injury reducing measures the tram company has now started to introduce include safety railings at tram stops, side barriers on the tramcars to prevent people from falling under the tram and lower speeds near tram stops.     

Comparative Judgments as an Alternative to Ratings: Identifying the Scale Origin.

Although comparative judgment methods have a number of distinct advantages over ratings, they share one common problem: On the basis of comparative judgments, it is not possible to recover the origin of item evaluations. One item may be judged more positively than another, but this result does not allow any conclusions about whether either of the items are attractive or unattractive. This article discusses the implications of this limitation for the interpretation of individual differences in comparative judgments. It also presents 3 different methods that may allow determination of the scale origin using a nested model comparison approach. An application illustrates the proposed approach as well as the benefits of determining the scale origin in understanding value judgments. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A new environmental friendly method for the preparation of sugar acids via catalytic oxidation on gold catalysts

A novel and efficient way of producing of aldonic acids is reported. The selective catalytic oxidation of monosaccharides (arabinose, ribose, xylose, lyxose, mannose, rhamnose, glucose, galactose, N-acetyl-glucosamine) and disaccharides (lactose, maltose, cellobiose, melibiose) on Au, Pd and Pt catalysts was investigated. By using the gold catalyst, a total selectivity with respect to aldonic acids and a high catalytic activity for all investigated sugars was found. The reaction conditions for the production of maltobionic and lactobionic acids via oxidation on gold catalysts were optimised. A high long-term stability of two different gold catalysts for the oxidation of maltose and lactose, respectively, was found.     

Long-term stability of an Au/Al2O3 catalyst prepared by incipient wetness in continuous-flow glucose oxidation

A 0.3% Au/Al₂O₃ catalyst prepared by the incipient wetness (IW) method was investigated in the continuous-flow liquid-phase glucose oxidation. Therefore, a continuous stirred tank reactor (CSTR) system equipped with an ultrasonic separator was used. The continuous-flow glucose oxidation was carried out at 40 °C, pH 9 and 1 bar oxygen partial pressure. Residence time and glucose concentration were varied. The IW gold catalyst showed very high activity and selectivity to gluconic acid within its 110 days of operation and, thus, an excellent long-term stability. Even after severe microbial contaminations of the catalyst, its activity could be completely restored by in situ regeneration with 2-propanol.