Thermal cure monitoring of phenolic resole resins based on in situ fluorescence technique

The thermal curing reaction of two phenolic resole resins is monitored using the fluorescence technique. The intrinsic fluorescence can be used as an indicator for cure monitoring for the first resole. As the thermal curing proceeds, the intrinsic fluorescence intensity of the resole resin decreases and exhibits a few nanometers of redshift. The fluorescence intensity of the emission maxima is correlated with the conversion measured by differential scanning spectroscopy. A linear correlation is found at three different temperatures. The intrinsic fluorescence cannot always be used for monitoring the curing process of phenolic resole resins. Thus, three intramolecular charge transfer compounds and two organic donor–π‐acceptor salts are selected and applied for the cure monitoring of the second phenolic resole resin. As the curing reaction proceeds, the fluorescence emission spectra of the probes exhibit a blue spectral shift and the intensity changes because of environmental changes. An intensity ratio method is applied in which the ratios of the low‐ to high‐intensity changes in the emission bands are used to determine the degree of the curing process. There is a smooth correlation between the intensity ratio method and the degree of cure. The method enables one to follow the changes in the polymer structure at low and intermediate degrees of the curing process (below 70%) and obtain comparable results from different types of probes during the same curing process. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1773–1780, 2002     

Survey of Intelligent Control Techniques for Humanoid Robots

This paper focusses on the application of intelligent control techniques (neural networks, fuzzy logic and genetic algorithms) and their hybrid forms (neuro-fuzzy networks, neuro-genetic and fuzzy-genetic algorithms) in the area of humanoid robotic systems. It represents an attempt to cover the basic principles and concepts of intelligent control in humanoid robotics, with an outline of a number of recent algorithms used in advanced control of humanoid robots. Overall, this survey covers a broad selection of examples that will serve to demonstrate the advantages and disadvantages of the application of intelligent control techniques.     

Monies,economies and democracy: cultivating ambivalence in the co-design of digital currencies

ABSTRACT

Systematised collaborative design of complementary currencies is still a largely unexplored area that offers underutilised opportunities for supporting a fair and sustainable sharing economy. Future currency design necessitates attention to the systemic factors and the social particularities in which new monetary alternatives, i.e. ‘monies’, and the technological solutions that serve these alternatives, are created. This paper argues for a socially and contextually sensitive design of complementary currency innovation. It considers the technological conditions and the tendencies to exploitation from contemporary capitalism. Based on the literature review, we propose collaborative design of complementary currencies with particularist and inclusive approaches. New directions for open-ended economic innovation are explored in finding opportunities in the future-oriented Transition Design, supported by an empathic and ambivalent design mindset.     

Two-step sintering technique for enhancing mechanical and oxygen permeation properties of dual-phase oxygen transport membranes

The present work involved the application of a two-step sintering (TSS) technique for typical Ce_0.9Gd_0.1O_2?δ–La_0.6Sr_0.4Co_0.2Fe_0.8O_3–δ (GDC–LSCF) composites and its effect on the microstructure and resultantly mechanical and O₂-permeating properties. The samples obtained by conventional sintering (CS) performed at 1100, 1250, and 1400 °C for 3 h exhibited maximum flexural strength and hardness values of 142 MPa and 8.71 GPa, respectively. However, the application of a TSS procedure produced fine-grained microstructures with improved mechanical properties. In particular, with the use of a typical 1250/1200 TSS protocol, increases of approximately 31 % and 7% in the flexural strength and hardness values, respectively, were observed compared to those obtained using the CS method. Moreover, thick-film (～ 60 μm) GDC–LSCF membrane prepared by tape casting and the TSS technique showed remarkably 1.5–2 times higher oxygen permeation flux than membrane sintered by CS method. The results are discussed and explained in detail.     

Low-Temperature Neutron Diffraction and Magnetic Properties of La1.2Sr0.9Ca0.9Mn2O7

The crystal structure and magnetic properties of a typical polycrystalline double-layered manganite, La_1.2Sr_0.9Ca_0.9Mn₂O₇, were examined using neutron diffraction and magnetization techniques. Neutron diffraction was performed at low and room temperatures and the crystal structure was refined using the Rietveld method based on the space group I4/Mmm. Low temperature neutron diffraction and magnetization measurements clearly revealed antiferromagnetic ordering. A neel transition was observed at approximately 150 K.     

Effect of the doping time of the 1‐butyl‐3‐methylimidazolium ionic liquid cation on the Nafion membrane proprieties

Nafion membranes were prepared by incorporating in the polymer matrix the 1‐butyl‐3‐methylimidazolium (BMI⁺) ionic liquid cation at different doping levels. Increasing the doping time of the membranes with the ionic liquid results in increased incorporation of the BMI⁺ cation but a decrease in the bulk conductivity. The thermogravimetric analysis shows that the BMI⁺ cation incorporation increases the thermal stability of the membranes. The higher discharge efficiency of the fuel cell at 80°C was obtained by using Nafion membrane after 15 minutes of doping in the ionic liquid solution.     

Insights into corrosion in dye solar cells

The main issue in using low cost metals in dye solar cells is the corrosion caused by the liquid electrolyte. Contrary to typical applications of metals, the adverse effects of corrosion in dye solar cells are related to irreversible depletion of charge carriers from the electrolyte rather than consumption of the metal itself. It is calculated that the penetration rate due to corrosion should not exceed 10⁻⁴ mpy (a couple of nanometers per year) to ensure device lifetime longer than 1 year. This is 10 000 times slower rate than what is considered to be a general benchmark value for very low corrosion rate in the field of corrosion science and has a major effect on how corrosion should be investigated in the case of dye solar cells. Different methods, their applicability, and limitations to investigate corrosion in dye solar cells are evaluated here. The issue with most techniques is that they can detect metals that are clearly corroding, but they have significant limitations in proving a metal stable. Our investigation shows that the most reliable information on corrosion is obtained from complete dye solar cells that are exposed to working conditions. A combination of color analysis of the electrolyte to such measurement is proposed as a means to extrapolate future performance of the cells and estimate potential lifetimes of the dye solar cells in regards to corrosion. Copyright © 2014 John Wiley & Sons, Ltd.     

Comparative Assay of Antioxidant Packages for Dimer of Estolide Esters

A series of 26 different antioxidants and commercial antioxidant packages designed for petroleum‐based materials, containing both natural and synthetic‐based materials, were evaluated with dimeric coconut‐oleic estolide 2‐ethylhexyl ester (2‐EH), a bio‐based material. The different antioxidants were categorized into different classes of phenolic, aminic, and blended/others materials. The oxidation onset temperatures (OT) using non‐isothermal pressurized differential scanning calorimetry (PDSC) were measured and recorded under previously reported standard conditions. The aminic series gave the best resistance to oxidation as defined by the PDSC method with OT of 246.6 and 244.7 °C for the best two performers, which was a 38 °C improvement over the uninhibited or unformulated dimer estolide material. The phenolic series, containing most of the naturally occurring antioxidants, was the least successful formulation package for the dimer estolide. The blended/other materials, which were specifically designed for petroleum‐based lubricants, did not have the best OT, since the estolides and other bio‐based materials interact differently than their petroleum counterparts. A number of potential antioxidants have been identified as useful additives for the estolides esters. The OT of the estolide and formulated materials correlated well with other bio‐based materials such as biodiesel.