Fabrication of Wear-Resistant Ti3AlC2/Al3Ti Hybrid Aluminum Composites by Friction Stir Processing

Metallurgical and Materials Transactions A - Hybrid nanocomposites have potential as wear-resistant materials. However, synthesizing these nanocomposites by conventional molten state methods result...     

Hydrotreatment of jatropha oil over noble metal catalysts

Jatropha oil is a promising nonedible feedstock for producing renewable diesel. In this work, the hydrotreatment processing of jatropha oil was investigated. Instead of using conventional alumina-supported Co–Mo, Ni–Mo, and Ni–W catalysts that need sulfidation pretreatment, noble metals such as Pd and Ru were chosen. Trials were performed in an isothermal trickle-bed reactor and the reaction conditions were as follows: temperature 603–663?K, weight hourly space velocity (WHSV) 1 to 4/h, pressure 1.5–3?MPa, and H₂/oil ratio 200–800 (v/v). Yield of n-C₁₅ to n-C₁₈ hydrocarbons was maximized (70.3 and 43.8% for Pd/Al₂O₃ and Ru/Al₂O₃, respectively) at the following conditions: T?=?663 K, WHSV?=?2/h, P?=?3?MPa, and H₂/oil ratio?=?600 (v/v). Since Ru favored cracking reactions to a larger extent than Pd, the yield of C₁₅ to C₁₈ hydrocarbons over Ru/Al₂O₃ was lowered. Using simple first-order plots for oil conversion, activation energies for the hydrotreating process over Pd/Al₂O₃ and Ru/Al₂O₃ were found and they were equal to 109 and 121?kJ/mol, correspondingly.     

Electrical conductivity of ferroelectric sodium vanadate,rubidium vanadate,cesium vanadate and their solid solutions

The d.c. electrical conductivity of sodium vanadate, rubidium vanadate, cesium vanadate and their solid solutions sodium-rubidium vanadate and sodium-cesium vanadate were studied by a two-probe method in the temperature range covering their transition points. The electrical conductivity shows sharp change at the phase transition temperature of these materials. In NaVO₃, RbVO₃ and CsVO₃, increase in d.c. conductivity is observed in the ferroelectric region while nonlinearities are observed above transition temperatures. In solid solutions, the activation energy in the paraelectric state is higher than that in the ferroelectric state and depends upon sodium concentration.     

Heat Transfer Analysis for Gas-to-Liquids Transportation Through Trans Alaska Pipeline

Gas-to-liquids (GTL) technology involves the conversion of natural gas to liquid hydrocarbons. In this article, theoretical studies have been presented to determine the feasibility of transporting GTL products through the Trans-Alaska Pipeline System (TAPS). To successfully transport GTL through TAPS, heat loss along the route must be carefully determined. This study presents heat transfer and fluid dynamic calculations to evaluate this feasibility. Because of heat loss, the fluid temperature decreases in the direction of flow and this affects the fluid properties, which in turn influence convection coefficient and pumping power requirements. The temperature and heat loss distribution along the pipeline at different locations have been calculated. Fairly good agreement with measured oil temperatures is observed. The powers required to pump crude oil and GTL individually, against various losses have been calculated. Two GTL transportation modes have been considered; one as a pure stream of GTL and the second as a commingled mixture with crude oil. These results show that the pumping power and heat loss for GTL are less than that of the crude oil for the same volumetric flow rate. Therefore, GTL can be transported through TAPS using existing equipment at pump stations.     

Effect of phase transfer catalysts on the interfacial tension of water/toluene system

The effect on the interfacial tension of the water toluene system has been studied at 25 °C in the presence of four phase-transfer catalysts i.e. tricaprylmethyl ammonium chloride, hexadecyltrimethyl ammonium chloride, hex-adecytrimethyl ammonium bromide and hexadecyltributyl phosphonium bromide. The interfacial tension of aqueous phenol/resorcinol-toluene in the presence and absence of tricaprylmethyl ammonium chloride has also been reported. Attempt has been made to elucidate the change in volumetric rate of extraction with different catalysts for two phase reactions, on the basis of interfacial tension.     

Analysis of conduction heat transfer problems in steady, 2D regions with circular holes using a special boundary integral method

A special boundary integral method developed for two-dimensional regions containing circular holes is used to calculate temperature and heat transfer on the boundaries of several selected regions. The geometrical configuration of the region is arbitrary and convective boundary conditions are assumed. An important feature of the method is analytic representation of temperature and its normal derivative on the interior circular holes in the form of a harmonic series. This makes the application of the boundary integral method convenient and free from conditioning problems associated with small interior boundaries. Heat transfer from circular isothermal interior holes are calculated for several illustrative examples using three terms of the harmonic series representation for heat transfer at each of the circular boundaries. The results are presented and discussed.