Critical slowing down in lead magnesium niobate–zirconate ceramic

Dielectric relaxation behaviour of (1 − x)PMN − xPZ, for x = 0.10, 0.30 and 0.40 have been studied. The nature of relaxational behaviour was found to change with PZ concentration. A crossover from a static freezing to critical slowing down like behaviour is observed with increase in Zr⁴⁺ concentration. We have used Glazounov and Tangastev criterion to distinguish freezing and critical slowing down like behaviour.     

Lean philosophy: implementation in a forging company

This research addresses the implementation of lean philosophy in a forging company with a focus on radial forging production flow lines. Here, the prime motive is to evolve and test several strategies to eliminate waste on the shop floor. In this research, a systematic approach is suggested for the implementation of lean principles. This paper describes an application of value stream mapping (VSM). Consequently, the present and future states of value stream maps are constructed to improve the production process by identifying waste and its sources. Furthermore, Taguchi’s method of design of experiments is pursued here to minimize the forging defects produced due to imperfect operating conditions. A noticeable reduction in set-up time and work-in-process (WIP) inventory level is substantiated. Finally, we conclude with a discussion of managerial implications and the future scope of research.     

Solution-Processed n-Type Organic Field-Effect Transistors With High on /off Current Ratios Based on Fullerene Derivatives

Solution-processed n-type organic field-effect transistors (OFETs) based on the fullerene derivative {6}-1-(3-(2- thienylethoxycarbonyl)-propyl)-{5}-l-phenyl-[5,6]-C61 (TEPP) and phenyl-C61-butyric acid methyl ester (PCBM) in a multiring source/drain structure are reported. Devices with TEPP show high electron mobility up to 7.8 x 10^-2 cm²/Vs in the saturation regime for bottom-contact OFETs with Au S/D electrodes with a solution-processed fullerene derivative. The ON/OFF ratios reported in this letter, which are in the range of 10⁵ -10⁶, are among the highest values reported for such devices. This mobility is always higher compared to PCBM devices prepared in identical conditions. The mobility of TEPP and PCBM increased with increasing temperatures in the range of 100-300 K with activation energy of 78 and 113 meV, respectively, which suggests that the thermally activated hopping of electrons is dominant in TEPP.     

A design advisor for the optimal inspection of circularity tolerance

In the wake of growing importance for quality and the need to reduce inspection costs simultaneously, the need for a scientific method of selecting an optimum inspection strategy for coordinate measuring machine (CMM) based inspection has become very important. The inspection error resulting from CMM inspection is greatly affected by the profile irregularities and the sampling strategy, which includes sample size, sampling methods, and algorithms used for form evaluation. This paper describes a system that can recommend an optimal inspection plan based on the needs of the user. A design of experiments (DOE) based approach is used to relate the inspection error with sampling strategies. Surface irregularities are included in the form of lobes formed on the profile. A new two-way model is proposed that works in both directions between the sampling strategy and the performance metrics. The results indicate that the number of lobes and the sampling method used have little impact on the inspection error, while the sample size and form evaluation algorithms have a significant influence. An inspection plan advisor is presented, which provides an inspection plan based on the estimated shape and acceptable measurement error.     

A unique method for reducing losses of bends in dielectric optical wave guide

The dielectric optical wave guide is finding growing attention at millimeter wave frequencies. However the dielectric optical waveguide radiates at bends and thus transmission loss increases. These radiations are in the outword direction of bends. This output radiation at output bends arises due to change in phase velocities of the propagating wave at the centre of the dielectric guide and the phase velocity at the outer surface of the dielectric guide. A unique methiod is suggested to avoid these radiation losses.Experimental results are also shown at microwave frequencies.     

Countercurrent water-heating system with a heat exchanger in a solar energy collector loop

The counter current heat exchanger theory with periodic inlet temperatures has been applied to analyze the thermal performance of a water heating system. The theoretical results obtained are in agreement with the experimental data reported in the literature.     

Consensus-based data replication protocol for distributed cloud

The Journal of Supercomputing - Data availability ensures efficient data accessibility by the readers anytime and from anywhere. It can be addressed by creating multiple copies of each data file...     

An investigation of grain boundary sliding in superplasticity at high elongations

Experiments were performed on the superplastic Zn-22% Al eutectoid alloy to determine the contribution of grain boundary sliding at both low (35%) and high (235%) elongations. The tests were conducted at two different strain rates in the superplastic Region II, and the results show that, within the accuracy of the measurements, there is a large sliding contribution at both elongations. By taking detailed measurements of both the magnitude of the sliding offset and the type of interface, it is shown that the average offsets are generally a maximum at the Zn-Zn boundaries, there is less sliding at the Zn-Al interfaces, and the offsets are a minimum at the Al-Al boundaries. In addition, the distributions of the magnitudes of the sliding offsets are similar at both the low and high elongations. It is concluded that grain boundary sliding is an important deformation process in the superplastic Region II and that it remains important even when the elongation is very high. The nature of the results indicates also that experimental observations of the deformation behaviour in superplastic materials at low elongations (up to 50%) provide meaningful information on the behaviour at much higher (superplastic) elongations.On leave from Mechanical Engineering Department, Nanjing Aeronautical Institute, Nanjing, Jiang-su 210002, People's Republic of China.     

High temperature mechanical properties of single phase alumina

The creep properties of a commercial, single phase aIurnina have been determined in the temperature range of 1623 to 1723 K. The stress exponent,n, in the relationship ⁿ was determined to be 1.9 and the true activation energy was found to be 635 kJ mol^–1. Normal primary stage creep transients were observed up to strains of 1%. At low stresses, steady-state conditions were not obtained due to the occurrence of concurrent grain growth. It is shown that the steady state creep results are consistent with the occurrence of an interface controlled diffusionaI creep mechanism.     

Studies on high-performance blended/multiblended cements and their durability characteristics

Number of blends were prepared by intergrinding clinker, gypsum, fly ash, calcined clay, microsilica and limestone in laboratory ball mill in varying percentages, and their physical properties such as fineness, consistency, setting time and compressive strength have been determined. The durability tests on selected compositions were also conducted by exposing the mortar cubes separately in 5% Na₂SO₄ and 5% NaCl solutions till the age of 90 and 180 days. The performance was observed by compressive strength development criteria after various length of exposure. Results have been discussed and found that the durability of blended cement is higher than the ordinary Portland cement.