排序方式: 共有175条查询结果,搜索用时 93 毫秒
1.
喷射沉积SiCP/Al复合材料及6066铝合金热挤压工艺的研究 总被引:4,自引:0,他引:4
作者应用喷射共沉积工艺制备 6 0 6 6 / Si Cp复合材料和 6 0 6 6铝合金锭坯 ,在不同的挤压比、挤压温度下挤压成 型 ,用金相显微镜观察材料的显微组织 ,并测试了材料的力学性能。结果表明 :Si C/ Al复合材料喷射沉积状态的组织很疏松 ,存在许多的间隙 ,其密度约为理论密度的 86 % ,Si C颗粒在复合材料中分布不均匀 ,喷射沉积铝合金基体的致密度可达 90 % ;挤压过程使 Al/ Si Cp复合材料的大多数空隙消失 ,致密程度随挤压比的增大而增大 ,挤压比超过 14 .7后不会明显变化 ,而铝合金基体的致密程度与挤压比的变化关系不明显 ;挤压温度对材料的致密程度影响不大 ;Al/ Si Cp复合材料性能在挤压比超过 14 .7后变化不大 ;铝合金的性能不受挤压比变化的影响 ;而挤压温度过高使材料性能下降 相似文献
2.
3.
高强铝合金断裂韧性的研究现状及展望 总被引:11,自引:0,他引:11
通过对三种裂纹模式的概述,引出了铝合金断裂韧性的概念及断裂判据,重点评述了影响高强铝合金断裂韧性的内在与外在因素,以及断裂韧性与其它力学性能间的关系,最后提出了几个在今后的研究及应用中需要重点解决的问题。 相似文献
4.
快速凝固粉末冶金TiB2颗粒增强AlFeVSi耐热铝合金 总被引:1,自引:1,他引:1
利用快速凝固粉末冶金方法制备了TiB2颗粒增强Al-8.5Fe-1.3V-1.7Si耐热铝合金试样以及不含TiB2颗粒的基体合金试样,通过光学显微镜、扫描电镜分析了其显微组织和断口形貌,采用X射线衍射进行了物相分析,并进行力学性能测试.结果发现,TiB2颗粒能有效地添加到Al-8.5Fe-1.3V-1.7Si耐热铝合金基体中,并能有效地抑制平衡相Al13Fe4的析出,且能细化晶粒,TiB2颗粒的存在使得粒度小于74μm粉末冶金合金挤压试样的室温强度高达454.1 MPa,屈服强度达407.8 MPa,延伸率保持在7.7%;350℃高温强度稳定在210 MPa以上,延伸率稳定在7.7%以上. 相似文献
5.
快速凝固耐热铝合金耐蚀性能的研究 总被引:2,自引:0,他引:2
采用腐蚀失重法和极化曲线,对比研究了FVS0611,FVS0812,2618,2618 Sc,2014,6061合金在人工模拟海水和海洋环境中的耐蚀性能。结果表明:2014,2618和2618 Sc腐蚀较严重;RS/PM生产的FVS0611,FVS0812和6061有较小的腐蚀速率,出现明显的钝化现象;并因为加工残余应力导致出现钝化-腐蚀-再钝化现象。 相似文献
6.
用粉末冶金方法生产、随后进行高温旋锻的Mo-5%W合金,其亚晶界存在着非常细的显微孔穴。实验表明:这些显微孔穴对小旋锻量的试样容易引起蠕变断裂,但对断面减缩率大于50%的试样则不会发生蠕变断裂。 相似文献
7.
8.
Crystallization process in rapidly solidified AI-Nd-Ni amorphous alloy prepared by melt spinning 总被引:1,自引:0,他引:1
Rapidly solidified ribbons of Al90Nd7Ni3 metallic glasses were prepared by using melt spinning. Crystallization process of the totally amorphous ribbons was investigated by differential scanning calorimetry and X-ray diffraction analysis, under continuous heating regime. The results show that, under continuous heating regime, the metallic glass devitrifies via two main stages: primary crystallization, resulting in two-phase mixture of a(Al) plus residual amorphous phase, and secondary crystallization, corresponding to some inter-metallic phases appearing,successively including A111 Nds, Als Ni, and some unknown phases, in the AI amorphous/crystal matrix. Four peaks appear on the continuous heating DSC curves. Their peak temperatures are respectively 470.8, 570.8, 585.6, and 731.6 K at infinitesimal heating rate, and their activation energies of the respective phase transformation are 183.0,294.7, 232.5 and 269.1 kJ/mol. The values of Avrami exponent of the four reactions decrease with increasing relative transformation degree. At the earlier stage of phase transformation, the values of n are larger than 4, and at the later stage the values of n become close to some value from 0.5 to 2.0. 相似文献
9.
Precipitated phases and thermodynamic analysis during solidification of Al-Fe-X system at slow cooling rate 总被引:4,自引:0,他引:4
1 INTRODUCTIONItisanimportantcharacteristicsthattherearelotsofexcellentthermalstablephasesinrapidsolidi fiedheatresistantAlalloys[16 ] .Strengtheningphas esinthesealloysmusthave goodstabilizationofstructureandheat resistance .IntheheatresistantAlalloys,thereismutualinteractionbetweenthealloyelementsandAlmatrix ,whichyieldsdifferenteffectsonthemicrostructuresand properties .Generally ,someaddingelementswithlowdiffusioncoefficientandlimitedsolidsolutioninthealuminiumcanformintermetallicco… 相似文献
10.