Correlation between motion of source bender element and feedback signal induced by self-monitoring

Since the introduction of bender element tests to soil testing, the reliability of the estimated travel time has been the most serious problem. The author has previously shown a potential solution whereby removing the response of the bender element subsystem from the whole response could dramatically improve the accuracy of the travel time estimation. In order to lay the foundation for estimating the response of the bender element subsystem, this paper examines the correlation between the displacements of the element and the induced feedback signals by employing a self-monitoring element. The response of the self-monitoring element is modeled as a transfer function involving two internal transfer functions that relate the input signals to the displacements and the displacements to the feedback signals, respectively. Using a laser displacement sensor, the displacements are directly measured through the entire surface and reveal the three-dimensional bending motion of the element oscillating in both longitudinal and width directions. The feedback signals are similar to, but inconsistent with, the tip displacements, and an attempt is made to correct the feedback signals. Finally, a conclusion is given on the potential for estimating the response of the bender element subsystem using the self-monitoring element.     

Fracture and deformation properties of Ni-Fe superalloy in cryogenic high magnetic field environments

The present paper includes experimental and analytical data on the fracture properties of a nickel-iron superalloy, a ferromagnetic austenite, at 4 K in magnetic fields of 0 and 6 T. The tensile, notch tensile and small punch tests are employed. A finite element analysis is also performed to convert the experimentally measured load-displacement data into useful engineering information. To interpret the results we review the available theory of the influence of magnetic field on the stress intensity factor for a crack in ferromagnetic materials.     

Nonlinear Optical Properties of TeO2-Based Glasses: MOx-TeO2 (M = Sc, Ti, V, Nb, Mo, Ta, and W) Binary Glasses

The third-order nonlinear optical susceptibilities, X⁽³⁾, of TeO₂-based glasses containing transition metal oxides (M = Sc₂O₃, TiO₂, V₂O₅, Nb₂O₅, MoO₃, Ta₂O₅, and WO₃) glasses have been measured by the third harmonic generation (THG) method in order to investigate the effect of the empty d-orbital contributions to the third-order nonlinear optical susceptibilities. It is found that the addition of TiO₂, Nb₂O₅, and WO₃ to TeO₂ glass increases the X⁽³⁾ value as well as the refractive index, while others decrease both of them. The positive effect of the TiO₂, Nb₂O₅, or WO₃, on the X⁽³⁾ of TeO₂ glass was interpreted in terms of the cationic empty d-orbital contribution. There is an almost linear relation between the X⁽³⁾ and the term (n²_ω+ 2)³.(n²_ω -1).E_d/E²₀ containing three measurable parameters only, irrespective of the kinds of MO, which was derived based on the bond orbital theory developed by M. E. Lines. The largest X⁽³⁾ value obtained is 1.69 × 10⁻¹² esu for 30NbO_2.5.70TeO₂ glass, about 60 times larger than that of pure fused silica glass.     

Photoelectrochemical properties of sol–gel-derived Ti1−xVxO2 solid solution film photoelectrodes

Ti_1−xV_xO₂ solid solution film photoelectrodes were prepared by the dip-coating sol–gel method. X-ray diffraction and X-ray photoelectron spectroscopy were employed to ensure the formation of the solid solution and their composition. Obvious photoresponses were observed in the visible region for the solid solution film electrodes with x0.05 and the red shift of the photoresponse was enhanced with increasing x. Moreover, the solid solution film electrodes were found to be photoelectrochemically stable. However, the onset potential of photocurrent shifted positively with increasing x. Band model of the solid solution was suggested to explain the effects of the vanadium incorporation on the photoelectrochemical properties.     

Effects of high molecular weight component on crystallization of polyethylene under shear flow

Crystallization of polyethylene (PE) blends of low and high molecular weight components under shear flow was studied using time-resolved depolarized light scattering (DPLS), focusing on effects of the high molecular weight component on the shish-kebab structure formation. Anisotropic two-dimensional scattering pattern due to shish-like structure formation was observed above a certain concentration of the high molecular weight PE. The threshold was about 2.5-3 times larger than the chain overlap concentration, suggesting an important role of entanglements of the high molecular weight component. On the basis of these results a gel-spinning-like mechanism for the shish-like structure formation has been proposed. The DPLS results also implied that the shish-like structure was mainly formed from the high molecular weight PE. This was confirmed by small-angle neutron scattering (SANS) and small-angle X-ray scattering (SAXS) measurements on an elongated PE blend of low molecular weight deuterated PE and high molecular weight hydrogenated PE (3 wt%).     

STM tunneling spectroscopy on high Tc superconductors

STM tunneling spectroscopy has been performed on the bulk single crystals of BiSrCaCuO (BSCCO) and the epitaxial thin films of YBaCuO (YBCO) at cryogenic temperatures. The STM images and tunneling spectra observed on the (001) surfaces can be classified into three cases; 1) Atomic image is visible. However, the tunneling spectrum shows semiconducting or smeared superconducting gap structures, depending on the tip-sample distance. 2) Clear atomic image can not be obtained. But, the tunneling spectrum shows flat bottom region with quite low zero bias conductance. 3) Tunneling spectra demonstrate gapless behavior, independent of the tip-sample separation. These observations support the quasi-2D electronic picture in whichs-wave like 2D superconducting layers are coupled with each other through the Josephson effect.     

Combined pars plana vitrectomy, lens removal and intraocular lens implantation for complications of diabetic retinopathy. Surgical results in 120 cases

We performed combined vitrectomy, lens removal and posterior chamber intraocular lens implantation for proliferative diabetic retinopathy in 120 eyes of 101 patients. Follow-up periods ranged from 3 to 63 months, with a mean of 17 months. Three lens removal methods were used: extracapsular cataract extraction (14 eyes), phacoemulsification and aspiration (49 eyes), and pars plana phacoemulsification (57 eyes). Preoperative rubeosis iridis or neovascular glaucoma was found in 21 eyes. Gas or temporary silicone oil tamponade was employed in 32 eyes. Surgical results were good, and the postoperative vision was finger counts or below only in 13 eyes. Thus the combined surgery proved to have no serious problems. Our results indicate two important points. (1) It is best to chose either of the following two methods for the lens surgery: phacoemulsification with continuous circular capsulorhexis, self sealing sclerocorneal incision, and in-the-bag fixation of the posterior chamber lens, or pars plana phacoemulsification leaving the anterior capsule, rub off and aspirating the lens epithelial cells, continuous circular capsulorhexis, and posterior chamber lens implantation in front of the anterior capsule from a self-sealing sclerocorneal wound. (2) It is mandatory to do complete vitrectomy and cut out the vitreous gels incarcerated in the sclerotomy site.     

Preparation of multiple oxide BaTiO3 fibres by the sol-gel method

Multiple oxide BaTiO₃ gel fibres were prepared by the sol-gel method from Ba(OC₂H₅)₂-Ti(O-isoC₃H₇)₄-H₂O-C₂H₅OH-CH₃COOH and Ba(CH₃COO)₂-Ti(O-isoC₃H₇)₄-H₂O-CH₃COOH solutions. Relatively long gel fibres of 10cm length were obtained from both solutions in the limited composition region. The latter solution in particular showed a spinnability even when it contained no water. Therefore, the occurrence of spinnability of the solution was considered to be due to the formation of linear polymers composed of bridging acetate groups such as TiO-C(CH₃)-O-Ti rather than metalloxane bonding as Ti-O-Ti. Addition of water to the solutions seems to break the bridging acetate bonds and replace some of them by bridging oxygen bonds. The as-drawn gel fibres which were X-ray amorphous crystallized into BaTiO₃ ceramic fibres of 5mm average length upon heating above 600 ° C. However, the gel fibres drawn from the sols without water became powdery on heating because of the lack of Ti-O-Ti metalloxane bonds. The crystallization behaviour of the BaTiO₃ gel fibres is discussed based on the infrared spectroscopy, X-ray diffraction analysis and thermogravimetric-differential thermal analysis.     

Structural changes of glass-ceramics of the Cu2O-Al2O3-SiO2 system on heating in air

The behaviour of copper ions in low thermal expansion glass-ceramics prepared from Cu₂O · Al₂O₃ ·_nSiO₂ glasses, or in-spodumene type Cu₂O · Ae₂O₃ ·nSiO₂ crystals included in the glass-ceramics on heating in air was investigated. On hewing at 300 to 500° C, the copper ions behaved as in the corresponding glasses. Cuprous ions in the glass-ceramics or-spondumene type crystals were oxidized into the cupric state, and at the same time an equal amount of cuprous ions to those oxidized were expelled out of the specimen for the requirement of electrical charge neutrality and then reacted with oxygen to form CuO on the surface. The oxidation of cuprous ions and the decrease of the copper content of the-spondumene type crystals brought about a considerable decrease in the lattice spooings.     

Molecular Mechanisms and Tumor Biological Aspects of 5-Fluorouracil Resistance in HCT116 Human Colorectal Cancer Cells

5-Fluorouracil (5-FU) is a cornerstone drug used in the treatment of colorectal cancer (CRC). However, the development of resistance to 5-FU and its analogs remain an unsolved problem in CRC treatment. In this study, we investigated the molecular mechanisms and tumor biological aspects of 5-FU resistance in CRC HCT116 cells. We established an acquired 5-FU-resistant cell line, HCT116R^F10. HCT116R^F10 cells were cross-resistant to the 5-FU analog, fluorodeoxyuridine. In contrast, HCT116R^F10 cells were collaterally sensitive to SN-38 and CDDP compared with the parental HCT16 cells. Whole-exome sequencing revealed that a cluster of genes associated with the 5-FU metabolic pathway were not significantly mutated in HCT116 or HCT116R^F10 cells. Interestingly, HCT116R^F10 cells were regulated by the function of thymidylate synthase (TS), a 5-FU active metabolite 5-fluorodeoxyuridine monophosphate (FdUMP) inhibiting enzyme. Half of the TS was in an active form, whereas the other half was in an inactive form. This finding indicates that 5-FU-resistant cells exhibited increased TS expression, and the TS enzyme is used to trap FdUMP, resulting in resistance to 5-FU and its analogs.