Dyeing properties of oxygen low-temperature plasma-treated wool and nylon 6 fibres with acid and basic dyes

Wool and nylon 6 fibres treated with oxygen low-temperature plasma were dyed with acid and basic dyes. Despite the increase of electronegativity of the fibre surface caused by the plasma treatment, the rate of dyeing of wool was increased with both dyes, while that of nylon 6 was decreased with the acid dye and increased with the basic dye.     

The effect of sputter etching on the surface characteristics of dyed aramid fabrics

Three kinds of aramid fabrics, Technora (modified p-aramid), Conex (m-aramid) and Kevlar (p-aramid), were subjected to sputter etching and argon low-temperature plasma treatments after dyeing in black with disperse dyes. The depth of shade increased considerably on Technora and Kevlar with the sputter etching treatment, but not on Conex fabrics. Argon low-temperature plasma treatment had virtually no effect on the depth of shade on the aramid fabrics.     

The effect of washing and heat treatment on the surface characteristics of fluorocarbon resin-treated polyester

Polyester fabrics and films treated with two fluorocarbon resins were washed and heat treated. Water repellency, surface tension and ESCA measurements were carried out. Changes in the water repellency of the resin-treated polyester fabric caused by washing and heat treatment are related to modification of the chemical composition of the polyester surface.     

Two-dimensional thickness measurements based on internal reflection ellipsometry

An imaging ellipsometer technique on internal reflection geometry that can measure the thickness distribution of a thin film possessing an assumed refractive index is described. Because a prism is used for the internal reflection geometry, it was theoretically predicted that angular derivation from the normal incidence on the prism surface affects only the psi value by a factor of 0.97 at maximum. Measurements were carried out for an optical system of silica substrate-TiO2 layer-silica layer-protein film-air, with a thin-film array of dried protein as the sample film. Thickness of the protein films was two-dimensionally estimated only from the measured map of the delta value by use of the simulated relationship between the thickness and the delta value. The thickness map obtained was coincident on the whole with the results according to a mechanical scanning. The detection limit was approximately +/- 0.2 nm. These findings validate the optical effect of a high-index additional layer to improve the sensitivity and precision of thickness measurements of the sample film on transparent substrates.     

Littrow-type external-cavity blue laser for holographic data storage

An external-cavity laser with a wavelength of 405 nm and an output of 80 mW has been developed for holographic data storage. The laser has three states: the first is a perfect single mode, whose coherent length is 14 m; the second is a three-mode state with a coherent length of 3 mm; and the third is a six-mode state with a coherent length of 0.3 mm. The first and second states are available for angular-multiplexing recording; all states are available for coaxial multiplexing recording. Due to its short wavelength, the recording density is higher than that of a 532 nm laser.     

Tunable blue laser compensates for thermal expansion of the medium in holographic data storage

A tunable laser optical source equipped with wavelength and mode-hop monitors was developed to compensate for thermal expansion of the medium in holographic data storage. The laser's tunable range is 402-409 nm, and supplying 90 mA of laser diode current provides an output power greater than 40 mW. The aberration of output light is less than 0.05 lambdarms. The temperature range within which the laser can compensate for thermal expansion of the medium is estimated based on the tunable range, which is +/-13.5 degrees C for glass substrates and +/-17.5 degrees C for amorphous polyolefin substrates.     

Analytical solution to compensate for thermal expansion change in photopolymer volume holograms using a tunable laser

For holographic data storage, it is necessary to adjust the wavelength and direction of the reading beam if the reading and recording temperature do not match. An analytical solution for this adjustment is derived using first-order approximations in a two-dimensional model. The optimum wavelength is a linear function of the temperature difference between recording and reading, and is independent of the direction of the reference beam. However, the optimum direction of incidence is not only a linear function of the temperature difference, but also depends on the direction of the reference beam. The retrieved image, which is produced by a diffracted beam, shrinks or expands slightly according to the temperature difference.     

Basic study of a ship navigator's mental workload using salivary NO\documentclass{article}\usepackage{amsmath}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{amsfonts}\pagestyle{empty}\begin{document}$_{3}^{-}$ \end{document}

Evaluation of the mental workload during training for ship handling has usually depended on professionals (captain, pilot) who have lots of experience on board. We are attempting to evaluate a ship navigator's mental workload based on a physiological index. The physiological indices, namely heart rate variability (R–R interval), nasal temperature, and salivary amylase, are good indices for reading the mental workload during ship handling. Moreover, we find the possibility of using salivary NO$_{3}^{-}$ as a good index for evaluating the ship navigator's mental workload. Salivary NO$_{3}^{-}$ is expected to have a specific characteristic to represent quick response on the spot and the trend. We confirmed the response of students during simulator training, and then carried out the experiment on professionals on a real ship. We propose that salivary NO$_{3}^{-}$ can show a ship navigator's stress for ship handling in the simulator and on a real ship. This work to evaluate the ship navigator's mental workload using salivary NO$_{3}^{-}$ is the first attempt worldwide. © 2013 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Modification of wool fibers by atmospheric pressure plasma treatment

Shrink‐proofing processing of wool fabrics by vacuum plasma treatment has been studied for many years. However, as a wool shrink‐proofing processing method, discharge treatment under atmospheric pressure, such as corona and low‐temperature electric plasma treatment, has been studied recently. In this study, an attempt was made to improve shrink‐proofing and other properties of a wool fabric by low‐temperature plasma treatment. The wool fabric was treated by pulsed atmospheric pressure plasma using a dielectric barrier discharge apparatus of the Institute of Textile Technology at Denkendorf by varying the power and flow rate of air. Shrink‐proofing, dyeing yield and water‐absorbing properties increased to a greater degree with the increase in the treatment time. However, the effect was saturated at 3 min. On the other hand, hysteresis of shearing property at large shear angle (2HG5), which is one of the mechanical parameters for measuring fabric hand by the Kawabata evaluation system (KES), becomes larger with the treatment time. It can be concluded that shear hysteresis value is related to the improvement in shrink‐proofing and other properties of the wool fabric.     

Laundering shrinkage of wool fabric treated with low-temperature plasmas under atmospheric pressure

Wool fabrics have been treated with helium/argon and acetone/argon low-temperature plasmas under atmospheric pressure. The plasma-treated fabrics were laundered several times and their shrink resistances investigated according to standard methods. Very high levels of shrink resistance to laundering were obtained through use of these treatments.