Pressure anomaly in the paramagnetic region of bcc solid3He

The isochoric pressure of bcc Solid³He in the vicinity of the triple point has been measured by changing the temperature stepwisely and waiting for thermal equilibrium. We observed anomalous pressure kinks of the temperature dependence in the paramagnetic region near the triple point. This anomaly appeared at 0.37 to 0.40 tesla, and disappeared below 0.36 tesla. Moreover, critical phenomena at the transition point from the paramagnetic phase (PP) to the high field phase was observed and the phase line curves toward the PP side.     

Growth condition of iodine-doped n+-CdTe layers in metal-organic vapor phase epitaxy

Iodine doping of CdTe layers grown on (100) GaAs by metal-organic vapor phase epitaxy (MOVPE) was studied using diethyltelluride (DETe) and diisopropyltelluride (DiPTe) as tellurium precursors and ethyliodine (EI) as a dopant. Electron densities of doped layers increased gradually with decreasing the growth temperature from 425°C to 325°C. Doped layers grown with DETe had higher electron densities than those grown with DiPTe. When the hot-wall temperature was increased from 200°C to 250°C at the growth temperature of 325°C, doped layers grown with DETe showed an increase of the electron density from 3.7×10¹⁶ cm⁻³ to 2.6×10¹⁸ cm⁻³. On the other hand, such an increase of the electron density was not observed for layers grown with DiPTe. The mechanisms for different doping properties for DETe and DiPTe were studied on the basis of the growth characteristics for these precursors. Higher thermal stability of DETe than that of DiPTe was considered to cause the difference of doping properties. With increasing the hot-wall temperature from 200°C to 250°C, the effective ratio of Cd to Te species on the growth surface became larger for layers grown with DETe than those grown with DiPTe. This was considered to decrease the compensation of doped iodine and to increase the electron density of layers grown with DETe. The effective ratio of Cd to Te species on the growth surface also increased with decreasing growth temperature. This was considered to increase the electron density with decreasing growth temperature.     

High-performance polymer alloys of polybenzoxazine and bismaleimide

Two series of high-performance polymer alloys were prepared by mixing typical benzoxine monomers, 3-phenyl-3,4-dihydro-2H-1,3-benzoxazine (P-a) or 6,6-(1-methylethyliden)-bis-(3,4-dihydro-3-phenyl-2H-1,3-benzoxazine) (B-a), with a typical bismaleimide, 4,4-bismaleimidodiphenyl methane by various ratios followed by thermal treatment up to 240 °C. DSC and IR of the alloys were examined to follow the curing reaction. These analyses showed that the obtained polymer alloys are AB co-cross-linked polymer networks through the formation of ether linkage between the hydroxyl group of polybenoxazine and the double bond of bismaleimide. Viscoelastic analysis and softening temperature measurement revealed that the polymer alloys have much higher glass transition temperatures than those of each homopolymer. The thermal stability also increased with the increase of bismaleimide content as evidenced by TGA.     

Subcellular localization of Bcl-2 protein in synovial sarcoma

The subcellular localization of Bcl-2 protein in surgically resected, fixed-frozen tissue specimens of seven tumors from six cases of synovial sarcoma and a synovial sarcoma cell line was examined using laser-scanning confocal microscopy and immunoelectron microscopy. Bcl-2 protein in synovial sarcoma cells was detected in the nuclear envelope, endoplasmic reticulum membrane, and mitochondrial circumference. Based on the finding of pre-embedding immunoelectron-microscopy observation, the distribution of Bcl-2 protein in such membranous organella was patchy. A computer-based image analysis failed to reveal any quantitative differences between the inner and the outer mitochondrial membranes. The tumorigenesis of synovial sarcoma is also discussed from the viewpoint of Bcl-2 overexpression.     

A PRACTICAL METHOD FOR RECTIFYING INTERFACIAL TENSION DATA TO PREDICT THE SHAPE OF INTERFACES IN AN IMMISCIBLE LIQUID/LIQUID/GAS SYSTEM

The shape of interfaces formed by the contact of two liquid phases, immiscible with each other, and a gaseous phase can be predicted on the condition that the tension to work at each interface is known with a sufficient accuracy. In general, interfacial tension data available are not so accurate, however, as to be useful as they are in predicting the shape of interfaces, particularly when the spreading coefficient of either liquid (liquid 1) on the other (liquid 2) has a negative value of a small magnitude. Presented in this note is a simple method to rectify the interfacial tension data, with the aid of a measurement of the radius of a lens of liquid 1 of a known volume placed on the horizontal surface of liquid 2, and thereby make them usable for predicting interfacial geometries. The method is tested by applying it to benzene/water and n-pentane/water systems.     

A new maritime lifesaving multiple-effect solar still design

This paper presents a new maritime lifesaving multiple-effect solar still design where several extended wicks feed seawater to their evaporating areas by capillary force, and the resulting water vapor diffuses and condenses on facing wicks with the condensate flowing through the wicks into storage bags. A theoretical analysis showed that a temperature drop through diffusion layers between evaporating and condensing wicks slowly increases in the main evaporating areas and rapidly near salt depositions whereas the evaporation rate decreases slowly in the main area and rapidly near salt depositions. These changes are caused by increases in salt concentrations and resulting boiling point elevation. With steady-state transfer analysis, the proposed still is predicted to produce about 15 kg m ⁻²d⁻¹ fresh water on a sunny day of 22 MJm⁻²d⁻¹ solar radiation, showing a potential to be a maritime lifesaving desalinator.     

Measurement of zeolite,silicate, and phosphate in laundry detergent products by inductively coupled plasma atomic emission spectrometry

This paper reports the development of a method for simultaneously measuring zeolite, silicate, and phosphate in laundry detergent products by inductively coupled plasma atomic emission spectrometry. A sample is decomposed under alkaline oxidative conditions to decompose zeolite, silicate, phosphate, and organic substances. Then hydrochloric acid is added to the decomposed solution to dissolve aluminum hydroxide precipitate before analysis. This sample preparation procedure was investigated by using a total organic carbon analyzer and was confirmed to be applicable to simultaneous measurements of zeolite, silicate, and phosphate. Relative standard deviation for the analysis is less than 2.1%, recovery is more than 99.0%, and the calibration curve gives a correlation coefficient ofR=1.000. The detection limit of this method for aluminum and silicon is 0.1%, and for phosphorus, 0.2% by weight in the product. This method is applicable to various laundry detergent products that contain zeolite, silicate, or phosphate and is five times faster than the three wet chemical methods.     

Changes in the Peeled Surfaces of Copper Thin Films Deposited on Polyimide Substrates After Heat Treatment

Peel strength between a copper (Cu) thin film and a polyimide (pyromellitic dianhydride-oxydianiline, or PMDA-ODA) substrate is reduced by heat treatment at 150°C in air. In this work, we investigated the peel strength, the morphology of the interface between Cu films and polyimide substrates using optical microscopy and electron microscopy, and chemical change of the interface using Auger electron spectroscopy (AES) and micro X-ray photoelectron spectroscopy (XPS). The analysis showed that CuO “lumps” were present on the peeled surface of PMDA-ODA after heat treatment at 150°C in air. The peeled surfaces of other polyimide substrates were also analyzed: biphenyl dianhydride-para phenylene diamine (BPDA-PDA) and biphenyl dianhydride-oxydianiline (BPDA-ODA). CuO lumps were present on the peeled surface of BPDA-ODA after the heat treatment, but not that of BPDA-PDA. Compared with the adhesion strength for the Cu thin film, the adhesion strength was high for the Cu/PMDA-ODA and Cu/BPDA-ODA laminates, but the adhesion strength was very low for the Cu/BPDA-PDA laminate. This low strength is the reason that CuO lumps were not detected on the peeled surface of the BPDA-PDA substrate. These CuO lumps were related to the adhesion degradation of the Cu/polyimide laminates after the heat treatment.     

Developing a Higher-Cycled Product Design CAE Model： The Evolution of Automotive Product Design and CAE

To help corporations survive amidst worldwide quality competition, the authors have focused on the strategic development of a higher-cycled product design CAE model employing a highly reliable CAE analysis technology component model. Their efforts are part of principle-based research aimed at evolving product design and CAE development processes to ensure better quality assurance. To satisfy the requirements of developing and producing high quality products while also reducing costs and shortening development times, the effectiveness of this model was verified by successfully applying it to the technological problems of loosening bolts and other product design bottlenecks at auto manufacturers.