Evolving an Accurate Decision Tree-Based Model for Predicting Carbon Dioxide Solubility in Polymers

Solubility is one of the most indispensable physicochemical properties determining the compatibility of components of a blending system. Research has been focused on the solubility of carbon dioxide in polymers as a significant application of green chemistry. To replace costly and time-consuming experiments, a novel solubility prediction model based on a decision tree, called the stochastic gradient boosting algorithm, was proposed to predict CO₂ solubility in 13 different polymers, based on 515 published experimental data lines. The results indicate that the proposed ensemble model is an effective method for predicting the CO₂ solubility in various polymers, with highly satisfactory performance and high efficiency. It produces more accurate outputs than other methods such as machine learning schemes and an equation of state approach.     

An experimental study of a cross-flow type plate heat exchanger for dehumidification/cooling

The thermal and dehumidification behaviour of a standard cross-flow type plate heat exchanger, intended for use as a dehumidifier/cooler, has been investigated both experimentally and numerically. Three sets of experiments have been carried out where air is blown into the primary and secondary sides of the exchanger, while water and liquid desiccant were being sprayed in a counter flow arrangement. The first set represents the indirect evaporative cooling of the primary stream by the secondary air stream. The second set is with liquid desiccant only and no indirect evaporative cooling. In the third set of experiments the primary air stream is indirectly evaporatively cooled by the secondary air stream and dehumidified by the liquid desiccant sprayed into the primary side of the exchanger. The above experiments indicate that the heat exchanger performs well when used with liquid desiccant. Furthermore, for an exchanger angle of 45°, there is an optimum value of air mass flow rate at which the effectiveness and dehumidification efficiency of the plate heat exchanger are maxima. To investigate the effect of the ambient air conditions on the PHE performance, further experiments were carried out using a heater element and a humidifier. The results show that under laboratory conditions the exchanger effectiveness and dehumidification efficiency increase with increasing primary air inlet temperature and humidity ratio. The experimental results were used to validate a computer model developed for the cross-flow type plate heat exchanger/dehumidifier. Comparison indicates that the numerical results are in good agreement with the experiments.     

A game attention model for efficient bit rate allocation in cloud gaming

The widespread availability of broadband internet access and the growth in server-based processing have provided an opportunity to run games away from the player into the cloud and offer a new promising service known as cloud gaming. The concept of cloud gaming is to render a game in the cloud and stream the resulting game scenes to the player as a video sequence over a broadband connection. To meet the stringent network bandwidth requirements of cloud gaming and support more players, efficient bit rate reduction techniques are needed. In this paper, we introduce the concept of game attention model (GAM), which is basically a game context-based visual attention model, as a means for reducing the bit rate of the streaming video more efficiently. GAM estimates the importance of each macro-block in a game frame from the player’s perspective and allows encoding the less important macro-blocks with lower bit rate. We have evaluated nine game video sequences, covering a wide range of game genre and a spectrum of scene content in terms of details, motion and brightness. Our subjective assessment shows that by integrating this model into the cloud gaming framework, it is possible to decrease the required bit rate by nearly 25 % on average, while maintaining a relatively high user quality of experience. This clearly enables players with limited communication resources to benefit from cloud gaming with acceptable quality.     

THE EFFECT OF PRECIPITATION PARAMETERS ON PREPARATION OF LITHIUM FLUORIDE (LIF) NANO-POWDER

Lithium fluoride powder (LiF) is a white powder with a density of 2.64 gr/cm³ and a melting point of 848°C. This powder has several applications such as flux, glaze, soldering, and aluminum melting process, but one of the most important uses of this powder is its application in dosimetry. The commercial powders currently used for this purpose have average sizes of 5 to 10 micrometers; the objective of this research is to produce LiF powder with nano-metric particle size. In this study, the reaction of LiOH + HF → LiF + H₂O has been selected from among several reactions that were able to produce LiF powder, and some precipitation parameters such as temperature, time, agitation type, and supersaturation degree have been controlled. The morphology, phase analysis, and particle size distribution of the resulting powders were analyzed by SEM, XRD, and LPSA. Finally, lithium fluoride nano-powder was synthesized at a temperature of 25°C, pH about 2-3, reaction time less than 1 s, and agitation by ultrasonic bath.     

Fault detection and diagnosis of an industrial steam turbine using a distributed configuration of adaptive neuro-fuzzy inference systems

The issue of fault detection and diagnosis (FDD) has gained widespread industrial interest in process condition monitoring applications. An innovative data-driven FDD methodology has been presented in this paper on the basis of a distributed configuration of three adaptive neuro-fuzzy inference system (ANFIS) classifiers for an industrial 440 MW power plant steam turbine with once-through Benson type boiler. Each ANFIS classifier has been developed for a dedicated category of four steam turbine faults. A preliminary set of conceptual and experimental studies has been conducted to realize such fault categorization scheme. A proper selection of four measured variables has been configured to feed each ANFIS classifier with the most influential diagnostic information. This consequently leads to a simple distributed FDD system, facilitating the training and testing phases and yet prevents operational deficiency due to possible cross-correlated measured data effects. A diverse set of test scenarios has been carried out to illustrate the successful diagnostic performances of the proposed FDD system against 12 major faults under challenging noise corrupted measurements and data deformation corresponding to a specific fault time history pattern.     

Homotopy perturbation method for motion of a spherical solid particle in plane couette fluid flow

He’s homotopy perturbation method is applied to obtain exact analytical solutions for the motion of a spherical particle in a plane couette flow. It is demonstrated that the applied analytical method is very straightforward in comparison with existing techniques. Furthermore, it is decidedly effectual in terms of accuracy and rapid convergence. The formulation of the problem is presented in the text as well as the analytical and numerical procedures. The current results can be used in different areas of particulate flows.     

Design, fabrication and control of a magnetic capsule-robot for the human esophagus

Much research on the development of a robotic capsule and micro robot for the diagnosis of gastrointestinal diseases has been carried out. The powering of these micro systems is becoming very challenging as the implementation of such systems is limited due to the existence of on-board power supplies. This paper presents a micro robotic system based on magnetic principles. The goal is to build a system in which a capsule-robot can be manipulated wirelessly inside an enclosed environment such as human??s body. A prototype of capsule-robot is built and tested, that can be remotely operated with three DOF in an enclosed environment by transferring magnetic energy and electromagnetic waves. A magnetic drive unit generates magnetic energy for the manipulation. Experimental results show the capsule-robot is manipulated and moved through a desired trajectory in a viscous fluid. The capsule-robot can be potentially used for endoscopy and colonoscopy.     

Blockwise conjugate gradient methods for image reconstruction in volumetric CT

Cone beam computed tomography (CBCT) enables volumetric image reconstruction from 2D projection data and plays an important role in image guided radiation therapy (IGRT). Filtered back projection is still the most frequently used algorithm in applications. The algorithm discretizes the scanning process (forward projection) into a system of linear equations, which must then be solved to recover images from measured projection data. The conjugate gradients (CG) algorithm and its variants can be used to solve (possibly regularized) linear systems of equations Ax=b and linear least squares problems minx∥b-Ax∥(2), especially when the matrix A is very large and sparse. Their applications can be found in a general CT context, but in tomography problems (e.g. CBCT reconstruction) they have not widely been used. Hence, CBCT reconstruction using the CG-type algorithm LSQR was implemented and studied in this paper. In CBCT reconstruction, the main computational challenge is that the matrix A usually is very large, and storing it in full requires an amount of memory well beyond the reach of commodity computers. Because of these memory capacity constraints, only a small fraction of the weighting matrix A is typically used, leading to a poor reconstruction. In this paper, to overcome this difficulty, the matrix A is partitioned and stored blockwise, and blockwise matrix-vector multiplications are implemented within LSQR. This implementation allows us to use the full weighting matrix A for CBCT reconstruction without further enhancing computer standards. Tikhonov regularization can also be implemented in this fashion, and can produce significant improvement in the reconstructed images.     

An integrated model for closed-loop supply chain configuration and supplier selection: Multi-objective approach

Reverse logistics consists of all operations related to the reuse of products. External suppliers are one of the important members of reverse logistics and closed loop supply chain (CLSC) networks. However in CLSC network configuration models, suppliers are assessed based on purchasing cost and other factors such as on-time delivery are ignored. In this research, a general closed loop supply chain network is examined that includes manufacturer, disassembly, refurbishing, and disposal sites. Meanwhile, it is managed by the manufacturer. We propose an integrated model which has two phases. In the first phase, a framework for supplier selection criteria in RL is proposed. Besides, a fuzzy method is designed to evaluate suppliers based on qualitative criteria. The output of this stage is the weight of each supplier according to each part. In the second phase, we propose a multi objective mixed-integer linear programming model to determine which suppliers and refurbishing sites should be selected (strategic decisions), and find out the optimal number of parts and products in CLSC network (tactical decisions). The objective functions maximize profit and weights of suppliers, and one of them minimizes defect rates. To our knowledge, this model is the first effort to consider supplier selection, order allocation, and CLSC network configuration, simultaneously. The mathematical programming model is validated through numerical analysis.     

A three-dimensional inverse finite-element method applied to experimental eddy-current imaging data

Eddy-current techniques can be used to create electrical conductivity mapping of an object. The eddy-current imaging system in this paper is a magnetic induction tomography (MIT) system. MIT images the electrical conductivity of the target based on impedance measurements from pairs of excitation and detection coils. The inverse problem here is ill-posed and nonlinear. Current state-of-the-art image reconstruction methods in MIT are generally based on linear algorithms. In this paper, a regularized Gauss-Newton scheme has been implemented based on an edge finite-element forward solver and an efficient formula for the Jacobian matrix. Applications of Tikhonov and total variation regularization have been studied. Results are presented from experimental data collected from a newly developed MIT system. The paper also presents further progress in using an MIT system for molten metal flow visualization in continuous casting by applying the proposed algorithm in a real experiment in a continuous casting pilot plant of Corus RD&T, Teesside Technology Centre.