Ruthenium dye-sensitized SnO2/TiO2 coupled solar cells

The photoelectrochemical behaviors of RuL₂(NCS)₂ dye-sensitized SnO₂/TiO₂ coupled solar cell was studied and compared with TiO₂ single system. The coupled system shows higher incident photon-to-current conversion efficiency (IPCE) value than the single system. A maximum IPCE value in the coupled system with 3.5 μm-thick SnO₂ and 7 μm-thick TiO₂ attained 82.4% at 530 nm wavelength. The higher IPCE value in the coupled system is attributed to the charge separation by fast electron transfer process from the excited RuL₂(NCS)₂ dye to TiO₂ to SnO₂ in the system with different energy level.     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

Attenuation of ischemic liver injury by prostaglandin E1 analogue, misoprostol, and prostaglandin I2 analogue, OP-41483

Workplace AIDS training is a recent addition to many corporations' occupational health agenda. However, little is known about the objectives, content, and practices of AIDS training programs. A survey of 126 workplace AIDS trainers was conducted to determine the impact of the trainer's organizational affiliation (in-house, consultant, union, etc.) and personal motives on training program objectives, content, and practices. Results indicate that the organizational affiliation of trainers is significantly related to training objectives, topics, and practices, whereas strong personal motives for becoming an AIDS trainer is significantly associated with an emphasis on more controversial content areas and training practices. Findings are discussed in terms of applicability to other values-oriented training topics, applications to practice, and future research needs.     

Theory and characteristics of novel variable reluctance 1X resolver

Although brushless resolvers have been used widely as angular position transducers, they are expensive due to their intricate construction, involving a rotary transformer to supply the exciting coils wound on the rotor poles with the current. It is shown theoretically in this paper that the resolver without rotary transformer or brushes can be realized by simple construction, which consists of the stator core with both 4-poles exciting windings and 2-poles output ones and the rotor core carrying no windings. In this resolver the rotor core has minimum gap at one side and a maximum gap at another side of the diameter. It is characterized by an outer surface form that makes the fluctuation part of gap permeance very in proportion to cos θ, where θ represents the angular position of a point in the air gap with respect to the origin on the rotor, the point of minimum air gap. The method determining the rotor form to embody the aforementioned gap permeance variation is also shown. It has been confirmed not only by simulation but also experiment that the 2-phase output voltages of a model designed based on the theory have sinusoidal waveforms with very small harmonic contents. Moreover, the rotor position detected by processing the output voltages through the conventional resolver/digital converter was within acceptable engineering accuracy.     

An abnormally shortened fatigue life of steels caused by anelasticity

Some abnormal fatigue life shortenings dependent upon load frequency for several steels are discussed. A possible relation between anelasticity caused by interstitial atoms and the abnormal fatigue life drop is presented. Normally, interstitial atoms are in a position which minimizes the energy around a dislocation, the Snoek ordering sites. We consider the Snoek effect as a typical example of anelasticity, and the possibility on atoms moving from attractive sites to repulsive ones when repeated stresses are applied and discuss a theory to explain the reduction of the fatigue life using Snoek ordered atoms moving out by fatigue stress at the frequency of Snoek effect. Bending fatigue tests were conducted to obtain the relationship between fatigue life and load frequency at two different temperatures (298 K and 333 K) for an iron nitrided steel. A sharp fatigue life drop was observed at a load frequency corresponding to the resonant frequency of the Snoek effect for nitrogen atoms. The frequency was about 3 Hz and 298 K and shifted to a higher frequency — about 6 Hz — at 333 K. Results reveal that the possible explanation to those abnormal phenomena may be anelasticity.Work partially conducted at Laboratorio E and Departamento de Ciencias de Materiales, Universidad Simón Bolívar, Venezuela.     

Thermal conduction mechanism of aluminium nitride ceramics

Extremely large grain size AIN ceramics were produced by HIP sintering at an ultra-high temperature of 2773 K without reducing the oxygen content in order to determine experimentally whether the factor controlling thermal conductivity is either grain boundaries or the internal structure of the grains. The room-temperature thermal conductivity of the HIPed AIN with a grain size of 40 m was 155 Wm^–1 K^–1, and was almost equal to that of the normally sintered AIN with a grain size of 4 m. Therefore, thermal conductivity at room temperature is independent of AIN grain size, or the number and amount of grain-boundary phase for reasonably well-sintered AIN ceramics. The calculated phonon mean free path of sintered bodies was 10–30 nm at room temperature, which is too small to compare with the AIN grain size. Consequently, it is shown that the thermal conductivity of sintered AIN is controlled by the internal structure of the grains, such as oxygen solute atoms.     

Effect of Grain Boundaries on Thermal Conductivity of Silicon Carbide Ceramic at 5 to 1300 K

The thermal conductivity of a SiC ceramic was measured as 270 W·m⁻¹·K⁻¹ at room temperature. At low temperatures ( T < 25 K), the decrease in the conductivity was proportional to T ³ on a logarithmic scale, which indicated that the conductivity was controlled by boundaries. The calculated phonon mean free path in the ceramic increased with decreased temperature, but was limited to ∼4 μm, a length almost equal to the grain size, at temperatures below 30 K. We concluded that the thermal conductivity of the ceramic below 30 K was influenced significantly by grain boundaries and grain junctions.     

Proposed Phenomenological PTCR Model and Accompanying Phenomenological PTCR Chart

The positive temperature coefficient of resistivity (PTCR) behavior of semiconductive BaTiO₃ is well explained by the Heywang model, which predicts the resistivity behavior above the Curie point based on the acceptor state density at the grain boundaries, the charge carrier density, and the energy gap, E _s, between the conduction band and the acceptor levels. However, the relationship between these parameters and the production parameters (sintering time, composition, and cooling rate) is not well understood. Recently, the present authors have found that E _s can be increased by thorough oxidation. This increase is attributed to a change in the oxidation state of the acceptor. Based on this finding and results from the literature, a phenomenological PTCR model and an accompanying PTCR chart for acceptor–donor-codoped BaTiO₃ are proposed to clarify this relationship. The PTCR chart clarifies that acceptor dopant concentrations, oxidation time, and oxygen partial pressure during oxidation or cooling can be optimized simultaneously to obtain optical PTCR properties.     

Experimental Evaluation of the Acceptor-States Compensation in Positive-Temperature-Coefficient-Type Barium Titanate

Experimental evidence shows that the acceptor-state levels in Sb-doped positive-temperature-coefficient-type BaTiO₃ are compensated up to a critical acceptor-state density. Using the slope of the natural logarithm of the resistivity with respect to 1/ T , instead of maximum resistivity as a measure for the acceptor-state density, it is possible to estimate this critical value. The value obtained (4.2 × 10¹⁷ m⁻²) is believed to be the first reported estimate based on experimental data. It is in good agreement with the estimate of 6 × 10¹⁷ m⁻² (first reported by Jonker) obtained from the spontaneous polarization of BaTiO₃. This shows that the ferroelectric behavior of BaTiO₃ is indeed a feasible explanation for the low resistivity below the Curie point, as proposed by Jonker.