Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Iodine-123-BMIPP myocardial washout and cardiac work during exercise in normal and ischemic hearts

Due to the changes in the frequency of penicillin-resistant strains of S. pneumoniae, it is necessary to perform surveillance studies of bacterial resistance. Isolates from the upper respiratory tract of asymptomatic children have been useful. There is no information about the difference between isolates from children with and without upper respiratory tract infection (URTI). The objective of the authors in this paper is to establish the prevalence of carrier-state, serotype and antimicrobial resistance of S. pneumoniae isolates from children with and without acute upper respiratory tract infection (URTI) in a rural area in Mexico. A cross-sectional comparative study was performed in Tlaxcala, Mexico. Children from one month 5 years of age were included. Nasopharyngeal swabs were obtained. Identification was done by international microbiology standards. Serotyping was done by the capsular Quellung test. The susceptibility testing was performed by the agar dilution method. Four-hundred and fifty patients were included. S. pneumoniae was isolated in 134 children (29.7%). Frequency of carriers was greater in patients with URTI (107/323) than without URTI (27/127) (33.1% vs. 21.1% p = 0.012, OR 1.84, IC 95% 1.1-3.08). The six most frequent serotypes were: 6B (16.4%); 19F (11.9%); 19A (6.7%); 14, 23F, and 35 (5.2% each), with no difference among the groups. Only 3% of the strains had high level resistance to penicillin, and 12.6% had intermediate resistance, and for ampicillin 4%, amoxicillin 4%, amoxicillin-clavulanate 4%, ceftriaxone 3%, cefotaxime 1.5%, erythromycin 6%, miocamycin 3%, chloramphenicol 4%, and vancomycin 0%. Trimethoprim-sulfamethoxazole resistance was very high (42%). In conclusion, colonization is higher in children with URTI. Five of the most frequent serotypes identified in this study were the same as those identified in patients with S. pneumoniae invasive diseases in Mexico City. In Tlaxcala, Mexico, beta-lactams could be the drug of choice for the treatment of S. pneumoniae lower respiratory tract infections. It is necessary to perform clinical assays to evaluate the efficacy of trimethoprim-sulfamethoxazole due to the high resistance in vitro.     

Studies on chitin. IX. Crosslinking of water-soluble chitin and evaluation of the products as adsorbents for cupric ion

Water-soluble chitin was successfully crosslinked to varying extents with glutaraldehyde in homogeneous aqueous solutions to improve the properties as an adsorbent for metal cations, and the effects of crosslinking were discussed. Complete insolubilization was achieved with the fivefold excess aldehyde, but, in terms of adsorptivity of Cu²⁺, the chitin crosslinked at an aldehyde/amino group ratio of 1.0 was found to exhibit remarkable capacity and was much superior to others. The desorption of Cu²⁺ from the adsorption complex was also attained effectively at pH 2.0. These results indicated that the loose crosslinking was quite simple and efficient to produce high capacity adsorbents for practical use. Thermal behavior of the crosslinked chitin was examined by TMA and TGA; a softening phenomenon was observed at 145°C.     

Electrical characterization of homoepitaxial diamond p–n junction

Electrical properties of homoepitaxial diamond p–n⁺ junction of boron (B)-doped p-type layer and phosphorus-doped n-type layer on Ib (111) diamond single crystal have been characterized. Current–voltage characteristics show a clear rectifying property with rectification ratio of over 10⁵ at ± 10 V. From capacitance–voltage characteristics, it is found that a spatial distribution of space-charge density N_i of the p–n⁺ junction is not uniform and N_i at a middle region of the space-charge layer formed at zero bias voltage is higher than that of other region of the space-charge layer. This peculiar characteristic can be explained by superposition of two effects; one is the deep dopant effect due to B atoms in the p-type layer, which makes to reduce N_i at around the edge of the space-charge layer formed at zero bias voltage. The other is the compensation of B acceptors by impurity atoms diffusing during the p–n⁺ interface and incorporating during the growth of p-type layer, which makes to reduce N_i at the vicinity of the p–n⁺ interface.     

Analysis of distribution of Campylobacter jejuni and Campylobacter coli in broilers by using restriction fragment length polymorphism of flagellin gene

The incidence of Campylobacter jejuni and Campylobacter coli in broiler farms was 33.9% (19/56). C. jejuni-positive flocks accounted for 20.0% (17/85) and C. coli-positive ones was 4.7% (4/85). There were 14 patterns (fla type) of restriction fragment length polymorphism (RFLP) of flagellin A gene among these 22 strains of C. jejuni and C. coli including the standard strain C. jejuni ATCC 33560. Different fla types of Campylobacter were isolated from broilers in different growing cycles on the same farms. Four strains of C. jejuni were isolated from four breeder farms and four fla types of C. jejuni were detected from their progenies reared on growing farms. Three fla types of C. jejuni detected from the progenies were different from those of each breeder. Also, the other three fla types of C. jejuni were detected from different progenies of each growing farm during the next growing cycle. These findings indicate that the RFLP analysis may contribute to epidemiological studies of C. jejuni and C. coli contamination of broilers and suggest the risk of contamination with different types of Campylobacter in every growing cycle of broilers on the farm even on the same farm. They also supported that there was little likeliness of the vertical transmission of C. jejuni and C. coli from breeders to broilers.     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

An all-digital analog-to-digital converter with 12-/spl mu/V/LSB using moving-average filtering

A compact, high-resolution analog-to-digital converter (ADC) especially for sensors is presented. The basic structure is a completely digital circuit including a ring-delay-line with delay units (DUs), along with a frequency counter, latch, and encoder. The operating principles are: (1) the delay time of the DU is modulated by the analog-to-digital (A/D) conversion voltage and (2) the delay pulse passes through a number of DUs within a sampling (= integration) time and the number of DUs through which the delay pulse passes is output as conversion data. Compact size and high resolution were realized with an ADC having a circuit area of 0.45 mm/sup 2/ (0.8-/spl mu/m CMOS) and a resolution of 12 /spl mu/V (10 kS/s). Its nonlinearity is /spl plusmn/0.1% FS per 200-mV span (1.8-2.0 V), for 14-b resolution. Sample holds are unnecessary and a low-pass filter function removes high-frequency noise simultaneously with A/D conversion. Thus, the combination of this ADC and a digital filter that follows can eliminate an analog prefilter to prevent the aliasing before A/D conversion. Also, both this ADC can be shrunk and operated at low voltages, so it is an ideal means to lower the cost and power consumption. Drift errors can be easily compensated for by digital processing.     

Mechanical alloying in the Al-Bi alloy system

Mechanical alloying (MA) was carried out to investigate the MA behaviour of the immiscible Al-10, 30 at % Bi alloys. After the MA processing, the Al and Bi were finely and homogeneously alloyed. The Bi crystallite size decreased to 25 nm and 30 nm in the Al-10 at % Bi and Al-30 at % Bi alloys, respectively. By increasing the MA time, the hardness increased up to a value of 80 H _v, which is larger than that obtained from the rule of mixtures. The lattice parameter of Bi decreased by about 0.27%, which shows the formation of a non-equilibrium hcp Bi super-saturated solid solution. The extended solubility of Al in Bi was 1.9% in the Al-30 at % Bi alloy. Due to the extended solubility, depression of the melting temperature of hcp Bi was confirmed in the mechanically alloyed Al-Bi alloys. The maximum depression in the temperature was about 10 K. The measured values corresponded well with those estimated from the extrapolation of the solidus line.     

Mechanism for high singlemode stability of gain-coupled DFB laserswith periodically etched quantum wells

The sidemode suppression ratio of gain-coupled DFB lasers with periodically etched quantum wells is analysed by a more accurate model for amplified spontaneous emission. It is shown that the periodic etching of quantum wells is very effective for providing a high side-mode suppression. The mechanism for the high singlemode stability is explained by the effective modal gain. which has an enhancement at the longer wavelength side of the Bragg stopband     

Analysis and design of combined distributed-feedback/Fabry-Perotstructures for surface-emitting semiconductor lasers

We propose combined distributed-feedback/Fabry-Perot (DFB/FP) structures for surface-emitting semiconductor lasers. The analysis is based on coupled-wave equations modified for surface-emitting lasers. The proposed structures, which exhibit enhanced resonance due to a matching between the gain and field distributions resulting in a reduced threshold compared with simple FP structures, are formed by placing the DFB structure between two DBR mirrors of an FP resonant cavity and introducing phase layers between the DFB region and the mirrors. It was found that the periodic-gain structures are a special case of the combined DFB/FP structures in which the index coupling effect is assumed to be negligible due to a small fill factor or a small refractive-index difference. The effect of complex (gain and index) coupling on the design and the threshold characteristics of the structures is clearly illustrated. Some important design considerations that were neglected in the previous papers are addressed