Transient liquid phase sintering of high-purity mullite for high-temperature structural ceramics

High-purity mullite ceramics, promising engineering ceramics for high-temperature applications, were fabricated using transient liquid phase sintering to improve their high-temperature mechanical properties. Small amounts of ultrafine alumina or silica powders were uniformly mixed with the mullite precursor depending on the silica-alumina ratio of the resulting ceramics to allow for the formation of a transient liquid phase during sintering, thus, enhancing densification at the early stage of sintering and mullite formation by the reaction between additional alumina and the residual glassy phase (mullitization) at the final stage of sintering. The addition of alumina powder to the silica-rich mullite precursor resulted in a reaction between the glassy silica and alumina phases during sintering, thereby forming a mullite phase without inhibiting densification. The addition of fine silica powder to the mullite single-phase precursor led to densification with an abnormal grain growth of mullite, whereas some of the added silica remained as a glassy phase after sintering. The resulting mullite ceramics prepared using different powder compositions showed different sintering behaviors, depending on the amount of alumina added. Upon selecting an optimum process and the amount of alumina to be added, the pure mullite ceramics obtained via transient liquid phase sintering exhibited high density (approximately 99%) and excellent high-temperature flexural strength (approximately 320 MPa) at 1500 °C in air. These results clearly demonstrate that pure mullite ceramics fabricated via transient liquid phase sintering with compositions close to those of stoichiometric mullite could be a promising process for the fabrication of high-temperature structural ceramics used in an ambient atmosphere. The transient liquid phase sintering process proposed in this study could be a powerful processing tool that allows for the preparation of superior high-temperature structural ceramics used in the ambient processing atmosphere.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

On A Maximum Likelihood Method for Clustering

Behaviormetrika - In this paper, we propose a new clustering method based on the concept of maximum likelihood (ML) estimation. In general, the problem of local minima arises when we try to use the...     

Highly reliable testing of ULSI memories with on-chip voltage-downconverters

Two testing techniques for ultra-large-scale integrated (ULSI) memories containing on-chip voltage downconverters (VDCs) are described. The first in an on-chip VDC tuning technique that adjusts internal V_CC to compensate for the monitored characteristics of the process parameters during repair analysis testing. The second is an operating-voltage margin test, performed at various internal V_CC levels during the water sort test (WT) and the final shipping test (FT)     

Inhibition of acid secretion in gastric parietal cells by the Ca2+/calmodulin-dependent protein kinase II inhibitor KN-93

A novel Ca2+/calmodulin-dependent protein kinase II (CaM Kinase II) inhibitor, KN-93 potently inhibits gastric acid secretion from parietal cells. As previously reported (1), treatment of parietal cells with a selective inhibitor of CaM kinase II, KN-62 resulted in the inhibition of cholinergic-stimulated rabbit parietal cell secretion, whereas it failed to inhibit the histamine and forskolin response. In contrast effects of carbachol, histamine and forskolin were significantly inhibited by KN-93 with an IC50 of 0.15, 0.3 and 1 microM, respectively; these effects occurred without any changes in intracellular cyclic AMP and Ca2+ levels. In the present study we investigated the mechanism by which KN-93 acts upon the acid-secreting machinery of gastric parietal cells. Neither redistribution of the proton pump activity nor the morphological transformation were affected by KN-93. The drug only weakly inhibited the H+, K(+)-ATPase activity but strongly dissipated the proton gradient formed in the gastric membrane vesicles and reduced the volume of luminal space. Thus KN-93 acts at pH gradient formation whereas KN-62 acts only at CaM Kinase II.     

Ozone micro-bubble disinfection method for wastewater reuse system.

Reuse of wastewater is regarded as one important way to deal with the world's shortage of potable water. The authors focused on a disinfection system using micro-bubbles and evaluated its capability for wastewater reuse. This paper reports experimental results from examination of the basic characteristics of micro-bubbles and disinfection of secondary effluent by air or ozone micro-bubbles. The results suggest that when micro-bubbles are applied in an ozonation system it is possible to reduce the reactor size, the amount of ozone decomposition equipment needed and the ozone dose rate.     

Hierarchical Clustering Method Using Probabilistic Similarity Measure

In this paper, we propose a new hierarchical clustering method, which is useful to find appropriate clusters of attributes from given dichotomous or frequency data. Important features of our method are 1) the similarity between two attributes is defined as a probability of their pattern vectors being observed under the hypothesis of independence, 2) for each generated cluster, one pattern vector is defined in a natural manner, and 3) it can be used freely without distinguishing the frequency data from the dichotomous one.

A typical frequency data is analyzed to illustrate how our method works effectively. The discussion on similarities among objects is also included to propose a new similarity measure based on our clustering method.

     

Relationship Between Local Atomic Arrangements and Properties of High-T c Superconductive Copper Oxides

Here various approaches to understanding the complex relationship among the local atomic arrangements, the distribution of charge/holes and the superconductivity characteristics are discussed for a variety of multi-layered copper-oxide superconductors. Regarding the structural parameters, i.e. bond lengths and angles, no single parameter is revealed to control the superconductivity characteristics alone. As a matter of fact, superconductivity properties are found to be correlated with the whole delicately balanced fine-structure that is described by a set of multiple parameters: it is shown that T _c and H_irr are enhanced in somewhat opposite ways. Expressing the delicately balanced fine-structure through the charge/hole distribution, it is concluded that the more homogeneously distributed the charge carriers are the more enhanced is the H_irr characteristics, while the opposite is likely to apply to the T _c value.