Ce对过共晶Al—Si合金熔体粘滞性和结构的影响

研究了Ce对Al—16％Si合金熔体粘滞性的影响。结果表明：Ce的加入增加了合金熔体的粘度，且随着Ce含量的增加粘度值也增加。结合加入Ce的Al—16％Si合金氢含量的变化、凝固组织和DSC曲线研究了熔体结构的变化，分析了粘度与液态结构变化之间的关系。     

Influence of process parameters on thermal-rate treatment of ZA42 alloy

Sand casting process and directional solidification technique combining thermal-rate treatment(TRT) were used. The influence of process parameters on TRT was investigated according to the values of impact toughness. At the same time, the mechanism of TRT was discussed. The results showed that TRT can improve the impact toughness of this alloy, while the hardness is basically constant. The time of heat preservation should not be more than 5min. Different forms of cooling intensification additive have different effects among which the zinc ingot solidified in graphite mold is the best one that can improve impact toughness of samples by more than 80%. With increasing the cooling temperature, the value of α(Al) crystal lattice constant increases. The element Sb has negative effect on TRT.     

Mg/Al异种材料真空扩散焊界面区域的显微组织

采用真空扩散焊技术对Mg／Al异种材料进行了焊接。采用金相显微镜、扫描电镜(SEM)、显微硬度计及X射线衍射(XRD)对扩散界面附近的显微组织及性能进行了试验研究。试验结果表明，Mg／Al异种材料真空扩散焊在加热温度Tp=450-490℃，压力强度P=0．08-0．10MPa，保温时间t=40-60min时能得到良好的扩散焊接头。扩散焊界面过渡区形成了致密的新相化合物层，断口形貌呈粗糙暗灰色，以解理断裂为主并伴有脆性的混合型断口，扩散界面过渡区生成了MgAl、Mg3Al2、Mg2Al3等金属间化合物。     

Effects of Ca addition on microstructure and properties of AZ63 magnesium alloy

1　INTRODUCTIONMg Alalloyshaveaverywideapplicationbecauseoftheirexcellentproperties ,lowmanufacturecost ,easymeltingtechniqueandnoexpensiveele mentscontent[1] .Oneofthiskindalloys ,AZ6 3mag nesiumalloy ,isawidelyappliedmagnesiumsacrifi cialanodewhichisusedextensivelyinundergroundandfreshwateratpresent .However ,compared withthataboard ,homesacrificialanodehassomedemer its :lowcurrentefficiencyandweakprotectionfunc tion ,soinvestigatingthehighdriving potentialandhighefficiencysacrificiala…     

机械合金化Al-Cu-Fe准晶相形成的研究进展

综述了机械合金化A1-Cu-Fe准晶相的形成机理及热力学稳定性方面的研究进展.     

高强度铸造铝合金细化剂的研制

针对Ａ１－Ｃｕ系高强度铸造合金研制了一种新型盐类晶粒细化剂，使合金晶粒明显细化，机械性能有显著的提高。试验结果表明，该细化剂具有长效性和很强的抗衰退能力，替代中间合金进行细化处理具有操作方便、加入量少和细化效果好等优点，有很高的经济价值。     

Si、Y对铸造Mg-Zn-Al合金组织性能的影响

研究了Si、Y对Mg-Zn-Al合金显微组织和力学性能的影响。结果表明：Si、Y均能提高合金的抗拉强度和硬度，特别对高温抗拉强度的提高效果更为明显。合金强度的提高主要得益于组织中析出相的弥散强化作用。Mg-6．0Zn-1．5Al-0．15Mn-1．2Si-0．5Y铸造镁合金的显微组织主要由a(Mg)基体、B(MgZn)相、λ(Mg2Si)相和ω(SiY)相组成。     

Processing technique and sliding friction and wear behavior of TiB2／ZA27 composite

In-situ TiB2 particles reinforced ZA27 composite was prepared by the stir-casting technique and a twostep method. TiB2/Al composite was produced by incorporating K2 TiF6, KBF4 salts and other agents into Al melt. As a master alloy, TiB2/Al composite was used to manufacture TiB2/ZA27 composite, which results in the generation of well-distributed reinforcing TiB2 phase. The hardness, friction and wear behavior of TiB2/ZA27 composite were investigated. The results show that the hardness of the composite is enhanced with increasing the content of TiB2 particles, the incorporation of TiB2 reduces the wear rate of TiB2/ZA27 composite and improves the friction property under lubricated and dry sliding friction conditions. The worn track width of ZA27 alloy is 1.6 and 2.5 times as long as that of 2.1%TiB2/ZA27 composite at 150 N and 700 N load under lubricated conditions, which indicates that TiB2/ZA27 composite possesses higher bearing ability.     

原位生成TiB2/ZA27复合材料的制备与性能

以Al熔液为载体,采用原位反应生成形状规则、尺寸细小的TiB₂颗粒相,再将TiB₂颗粒传递到ZA27合金中,形成TiB₂颗粒增强的ZA27复合材料。采用合理的熔炼工艺促进了TiB₂颗粒在基体中的均匀分布。实验结果显示,TiB₂颗粒在ZA27复合材料中,分布均匀,平均直径在3 μm以下。TiB₂颗粒的加入使得复合材料的晶粒明显细化,并随着TiB₂颗粒含量增加,复合材料的抗拉强度、硬度明显提高,2.1%TiB₂/ZA27复合材料与基体合金相比室温抗拉强度提高13%、布氏硬度提高21%,弹性模量也有所提高,在强度、硬度及弹性模量提高的同时,材料的塑性并未恶化,延伸率略有提高,另外,材料的热膨胀系数随着TiB₂颗粒的加入有所降低。     

铸铁合金的遗传效应及其利用

研究了亚共晶，过共晶铸铁合金液在不同热状态下凝固组织，以及组织对力学性能的影响等，发现，炉料对铸件产生明显的组织遗传效应，随合金液过热温度的升高，铸件吉石墨相的数量减少且变细，碳化物增多，组织趋于均匀，合金的硬度提高，冲击韧性下降；随合金液保温时间延长，组织遗传性衰退，石墨相球化，碳化物变细，设计的热处理新工艺能提高合金的力学性能，根据遗传观点，分析了试验结果及其意义，探讨了热速处理的作用机理。