Costs of air pollutants from shipping: a meta-regression analysis

ABSTRACT

This study estimated the external cost of air pollution from shipping by means of a meta-regression analysis, which has not been made before. Three pollutants, which were included in most of the primary studies, were considered: nitrogen oxides (NO_x), sulphur dioxides (SO₂) and particulate matters with a diameter of max 2.5 micrometres (PM_2.5). All primary studies included damages of health and a majority added impacts on agriculture and estimated the cost of air pollutants by transferring cost estimates from studies on costs of air emissions from transports in Europe. Different regression models and estimators were used and robust results were found of statistically significant emission elasticities of below one, i.e. total external costs increase by less than 1% when emissions increase by 1%. There was a small variation between the pollutants, with the highest elasticity for PM_2.5 and lowest for NO_x. Calculations of the marginal external cost of the pollutants showed the same pattern, with this cost being approximately six times higher for PM_2.5 than for the other pollutants. Common to all pollutants was that the marginal external cost decreases when emission increases. Another robust result was a significant increase in the cost of studies published in journals compared with other publication outlets. These findings point out some caution when transferring constant external unit cost of air pollutant from shipping, which is much applied in the literature, and the cost functions estimated in this study could thus provide a complementary transfer mechanism.     

The Nonlinear Behaviour of a MacPherson Strut Wheel Suspension

Three nonlinear models of a MacPherson strut wheel suspension have been studied. The nonlinearities considered are due to the nonlinear geometrical effects in the mechanism, the amplitude limitation due to the bumpstop, the progressive stiffness of the bumpstop and the different damping coefficients for the shock absorber in bump and rebound. The models have been derived according to physical parameter values of. the MacPherson strut wheel suspension of the car SAAB 9.000. The most suitable model was further studied with special attention to nonlinear phenomena. For harmonic forcing the system had phenomena such as multiple solutions and subharmonics. For some parameter values the solution was very sensitive to changes in the integration tolerances in the numerical integration routine. No chaotic steady state solutions were found for the parameter values studied.     

Dynamic Behaviour of Ore Wagons in Curves at Malmbanan

The transportation of ore can be made more cost efficient by use of bigger and heavier trains. An increase in axle load is thereby wanted. The fleet of ore wagons of today at Malmbanan/Ofotbanan in northern Sweden and Norway has to be updated. It is of interest to find out if it is possible to allow a higher axle load on the track with new wagons

To be able to understand and predict the effects on track wear depending on what type of vehicle that is in use, the contact forces between wheels and rails have to be determined. A computer aided analysis has been made of the dynamic behaviour of three test vehicles equipped with different types of three-piece bogies running at Malmbanan. The vehicles are modelled and their interaction with the track is analysed using the multibody simulation package GENSYS

The simulations show that, even if the axle load is increased from 25 tons to 30 tons and the velocity is increased from 50 km/h to 60 km/h, it is possible to reduce lateral track forces and wear in curves by using a different bogie than the standard three-piece bogie used today.     

Simulation and Visualisation of the Dynamic Behaviour of an Overhead Power System with Contact Breaking

For high speed rail traffic it is necessary to design overhead power systems which minimize the contact loss between pantograph head and contact wire. To predict how different design solutions will behave it is favourable to model and simulate the dynamic behaviour. In this paper a model of an overhead power system is specified and used in simulation. The model is suitable for simulation with contact loss since it includes specifications of impact conditions between pantograph head and contact wire. Two sets of equations of motion are specified, one for the contact case and one for the non-contact case. The model also includes lateral movement of the wire due to the zigzag span and friction between the pantograph head and the contact wire. It is shown how to make animations of the system behaviour using a MCAE-system. The animations are made using a geometrical model of the system together with results from numerical simulations.

Through the examples provided, use of the mathematical model and the geometrical model is presented. The response is visualised as time histories and phase plane diagrams of different coordinates and as animations of the total system response. The different types of visualisations make an excellent combination when studying the system behaviour of different design solutions.

In one example, simulation using the linearised set of equations gives the same results as simulation using the set of fully nonlinear equations, due to periodic response and the simple alternation of contact conditions. It is shown that the situation when any of the parameters vary suddenly is possible to simulate using the fully nonlinear equations of motion.     

Advanced vehicle dynamics of heavy trucks with the perspective of road safety

ABSTRACT

This paper presents state-of-the art within advanced vehicle dynamics of heavy trucks with the perspective of road safety. The most common accidents with heavy trucks involved are truck against passenger cars. Safety critical situations are for example loss of control (such as rollover and lateral stability) and a majority of these occur during speed when cornering. Other critical situations are avoidance manoeuvre and road edge recovery. The dynamic behaviour of heavy trucks have significant differences compared to passenger cars and as a consequence, successful application of vehicle dynamic functions for enhanced safety of trucks might differ from the functions in passenger cars. Here, the differences between vehicle dynamics of heavy trucks and passenger cars are clarified. Advanced vehicle dynamics solutions with the perspective of road safety of trucks are presented, beginning with the topic vehicle stability, followed by the steering system, the braking system and driver assistance systems that differ in some way from that of passenger cars as well.     

Effects of increased awareness on choice of travel mode

This paper reports a field experiment with the purpose of studying the effects of increased awareness on travel mode choice. One hundred fifteen subjects were randomly assigned to an experimental and a control group. In the experimental group, a more deliberate choice of travel mode was induced and expected to result in a stronger relationship between attitude and behavior, a weaker relationship between habit and behavior, and a behavioral change among individuals with a strong habit. Attitude, habit, and behavior were measured in travel diaries and questionnaires. The results indicated no significant change in the relationship between attitude and behavior and no significant change in the relationship between habit and behavior. However, a temporally extended decrease in car use was observed in the experimental group. The effect was noted for individuals with a strong habit who reduced their car use but not for subjects with a weak habit.     

Consequences of Nonlinear Characteristics of a Secondary Suspension in a Three-Piece Freight Car Bogie

Mechanical systems with nonlinear characteristics can show a complex dynamic behavior that should be taken into account when analysing dynamic performance and reliability. The dynamic behavior of the main suspension in a three-piece freight car bogie with constant friction damping is considered in this work. The aim is to investigate the vertical behavior of a specific suspension design due to different driving conditions, weather and wear of the friction wedges. A variation in weather and wear is represented by different friction configurations in the model of the suspension. Models of different levels of detail that are based on experimental data on existing designs are developed. It is found that the suspension performance is very sensitive to variations of the friction configuration and this indicates a possible presence of nonlinear dynamic phenomena at in service like conditions.     

Single wheel hub motor failures and their impact on vehicle and driver behaviour

This research work studies the impact of single wheel hub motor failures on the dynamic behaviour of electric vehicles and the corresponding driver reactions. An experimental study in a moving-base driving simulator is conducted to analyse the influence of single wheel hub motor failures for motorway speeds. Driver reaction times are derived from the measured data and discussed in their experimental context. The failure is rated objectively on the dynamic behaviour of the vehicle and compared to the subjective evaluation. Findings indicate that critical traffic situations impairing traffic safety can occur for motorway speeds. Clear counteractions by the drivers had to be taken.