Detection of Multiple Blockages in Parallelized Microreactors

In a plant consisting of parallelized microreactors (MRs), the product quality is lowered because of a lack of flow uniformity among them when blockage occurs. It is not practical to install sensors in every MR from the viewpoint of cost when detecting the blocked MRs. In the previous study, the multiple blockage detection (MBD) method using a small number of sensors was proposed, but its performance became low when the number of sensors decreased. Here, the conventional algorithm for MBD is improved by considering the process behavior on blockage occurrence, and the effectiveness of the improved algorithm is demonstrated through a numerical case study. The effects of flow distributor types and sensor types on the MBD performance are numerically investigated.     

Tuning-current splitting network for three-section DBR lasers

A simple current-splitting network for DBR-laser frequency tuning is proposed that distributes a single control current among two tuning sections and can adjust the current distribution without yielding impedance mismatching. The nonlinear characteristics of the tuning sections realise the non-proportional current splitting suitable for continuous tuning; 470 GHz (3.8 nm) tuning range is achieved     

Phase fluctuations of cross-polarized signals at 4 GHz in fine weather on earth-space paths

On an earthspace propagation path with the low elevation angle of 10 deg, the phase between co- and crosspolar signals occasionally showed rapid and irregular fluctuations during fine weather. These fluctuations were generally significant during the daytime, and were strongly in phase with the occurrence of the copolar amplitude scintillations. This could be attributed to the combined effects of the crosspolar phase pattern of the receiving antenna and small fluctuations of the angle of arrival of the radiowaves.     

Electrochemically induced asymmetrical etching in InAlAs/InGaAs heterostructures for MODFET gate-groove fabrication

We have achieved a self-controlled asymmetrical etching in metalorganic chemical vapor deposition-grown InAlAs/InGaAs heterostructures, which can be suitable for fabricating modulation-doped field-effect transistors (MODFETs) with gate-groove profiles for improved performance. The technology is based on electrochemical etching phenomena, which can be effectively controlled by using different surface metals for ohmic electrodes. When surface metals of Pt and Ni are deposited on the source and the drain, respectively, the higher electrode potential of Pt results in slower etching on the source side than on the drain side. Thus, asymmetry of gate grooves can be formed by wet-chemical etching with citric-acid-based etchant. This represents a new possibility to conduct “recess engineering” for InAlAs/InGaAs MODFETs.     

The importance of electrochemistry-related etching in thegate-groove fabrication for InAlAs/InGaAs HFETs

For the first time, the surface metal on nonalloyed ohmic electrodes is found to significantly change the profiles of gate grooves, when resist openings are employed to monitor drain current during wet-chemical gate recess for sub-micron InAlAs/lnGaAs heterojunction field-effect transistors (HFETs). The surface metal of Ni enhances the etching rate in comparison with that in the absence of electrodes by a factor of 4 and 10, laterally and vertically, which is favorable to fabricate deep gate grooves with small side etching. The Pt surface metal, however, leads to preferential etching of InGaAs over InAlAs, which can be useful to realize large side etching. The existence of an electrochemistry-related etching component, which arises when the ohmic electrodes are present during recess etching, is considered to be responsible for these behaviors     

Design and characteristics of InGaAs/InP composite-channel HFET's

A design for composite-channel structures consisting of an InGaAs channel and an InP subchannel for use as heterostructure field-effect transistors is presented for the first time. This novel channel structure takes advantage of both the high drift velocity and low impact ionization of InP at high electric fields as well as the high electron mobility of InGaAs at low electric fields. It is shown that the doping density of the InP subchannel is the key parameter to realize the advantages of the composite channel. A very high transconductance of 1.29 S/mm and a current gain cutoff frequency of 68.7 GHz are achieved with 0.6 and 0.7 /spl mu/m gates, respectively. The average velocity of electrons in the composite channel is 2.9/spl times/10/sup 7/ cm/s. The devices have no kink phenomena in their I-V characteristics possibly due to low impact ionization in the InP subchannel.<>     

Formation and Characterization of Ce3ZrO8 Prepared by the Hydrazine Method

A compound denoted as (Ce_0.75Zr_0.25)O₂ (Ce, ZrO₈) is formed near room temperature from cerium and zirconium nitrates using hydrazine monohydrate. It has a cubic unit cell with a = 0.5342 nm. Characterization of powders heated to various temperatures at 10°C/min demonstrates that the specific surface area does not decrease below 20 mVg until >1000°C.     

Inhibitory effect of alpha-tocopherol on methemoglobin formation by nitric oxide in normal and acatalasemic mouse hemolysates

The inhibitory effect of alpha-tocopherol on methemoglobin formation in normal and acatalasemic mice was studied by exposing their hemolysates to nitric oxide. Methemoglobin formation in normal and acatalasemic mouse hemolysates exposed to nitric oxide were significantly inhibited by the addition of alpha-tocopherol at final concentrations ranging from 1.2 to 5.8 mM. Negative correlations were observed between the logarithm of alpha-tocopherol concentration and the methemoglobin formation. The formation of methemoglobin in acatalasemic mouse hemolysates was greater than that in normal mouse hemolysates with or without added alpha-tocopherol. The methemoglobin formation in acatalasemic mice was also significantly inhibited by addition of more than 500 units/ml of catalase, and the methemoglobin formation in normal and acatalasemic mice was also inhibited with sodium diethyldithiocarbamate at a final concentration of 1 M.