Fracture toughness evaluation of adjacent flow weld line in polystyrene by the SENB method

Fracture toughness of adjacent flow weld lines, defined as weld lines that occur when two flow fronts meet and continue to flow together in the same direction (meld line or hot weld line), was evaluated by the single‐edge notched‐bend (SENB) method using three differently‐shaped obstructive pins. Although the fracture toughness varied depending upon the shapes of the pin, the values could be standardized as the distance from the meeting point of the two flow fronts flowing around the pin. The fracture toughness decreased drastically from the meeting point along the weld line and then slightly increased. These characteristic features could be explained by flow‐induced molecular orientation at the weld line interface. The molecules around the meeting point that were initially oriented parallel to the weld line due to fountain flow were able to relax, and then entanglement across the weld line interface developed because the flow stopped in the middle of the filling process, resulting in high fracture toughness. In contrast, the material at the downstream side of the weld line continued flowing during the filling process, being stretched along the flow direction. So, the molecular orientation at this area could not relax. In addition, the V‐notch shape, i.e., the depth and length at the surface of the weld line, which also varied depending on the shape of the obstacles, was considered to be identical when the meeting point was allowed to be a datum point. Thus, the meeting point was found to be a significant factor when the properties of weld lines are investigated. POLYM. ENG. SCI., 45:1059–1066, 2005. © 2005 Society of Plastics Engineers     

Sputter deposition technology as a materials engineering

Sputter deposition is currently being widely used in the microelectronics industry for the production of silicon integrated circuits. Recently interest has been focused on sputter deposition as a new materials processing technique. The highly energetic sputtered atoms enhance crystal growth and/or sintering during film growth. This results in lowering of the growth temperature of high temperature materials including cubic diamonds. Single crystals of complex ceramics materials could be prepared by sputter deposition through epitaxial growth process. Atomically controlled deposition using multi-target sputter enables to make man-made superlattice including high-T _C superconductors of layered perovskite. At present sputter deposition is one of key materials technologies for the coming century.     

Temperature dependence of kinetics and diffusion coefficients for ferrocene/ferricenium in ammonium-imide ionic liquids

The electrochemical behavior of ferrocene (Fc) and ferricenium (Fc⁺) was investigated by cyclic voltammetry with convolutional and semi-differential electroanalyses in the temperature range 298-373 K in the hydrophobic room temperature ionic liquid systems consisting of bis(trifluoromethanesulfone)imide anion with quaternary ammonium cation. The experimental results indicated that the redox reaction of Fc/Fc⁺ was reversible in this ionic liquid and the charge-transfer rate constant (k⁰) has been obtained. Mass transport towards the electrode is a simple diffusion process and the diffusion coefficient (D) for Fc/Fc⁺ has been also calculated. These results indicated that the k⁰ and D increased with increasing temperature in ionic liquids. The validity of the Arrhenius law was verified by investigating the temperature dependences of k⁰ and D.     

Physicochemical Properties of Palm Oil-Based Puff Pastry Model Margarines Related to Their Baking Performance in Long-Term Storage

Developing trans-free alternative fat solutions suitable for specific applications remains a challenge in edible fats and other domains. This is particularly true for palm oil-based puff pastry margarines, which suffer from post crystallization problems, leading to dramatic loss of functionality. This research is aimed at investigating the influence of triacylglycerol (TAG) compositions of palm oil-based puff pastry margarines on the physical properties of the fat crystal network, which determine the functionality of such products. Three model puff pastry margarines are produced at pilot scale under the same crystallization conditions. They share the same fatty acid composition and close solid fat content (SFC) profiles, whereas the proportions of major TAG (tripalmitoylglycerol (PPP), 1,3-di-palmitoyl-2-oleoylglycerol (POP), 1,2-di-palmitoyl-3-oleoylglycerol (PPO), 1,2-dioleoyl-3-palmitoylglycerol (POO)) are different. Polymorphism, melting profile, hardness, microscopic structures, and baking performance (puffing effect) of the model fats are examined during a period of 6 months. The following results are obtained: 1) The TAG composition significantly influences the post crystallization processes occurring in palm oil-based margarines. 2) High amounts of POP show negative influences. 3) The proportions of POP, PPO, and PPP should be carefully balanced to prevent detrimental crystal network rearrangements, leading to textural modifications (hardness increase) and significant reduction in baking performance. Practical Applications : The results presented in this work could be helpful for edible fat products developers, especially for roll-in fat applications. This research provides an overview of the relevant properties to study for the assessment of puff pastry margarine functionality. It also highlights the importance of ensuring long-term stability of palm oil-based fat products. Finally, it emphasizes that certain combinations of fat materials should be avoided to maintain the quality of palm oil-based puff pastry margarines.     

Humidity Sensor Characteristics of Woodceramics

The humidity sensor characteristics of Woodceramics were investigated. The Woodceramics used in this experiment were prepared at 650–900°C. The size of specimens selected was 1 × 1 × 10 mm . One was used as-cut and the other was polished. Above 700°C, the resistance of the specimen was below 50 and the decrease of resistance with increasing relative humidity was small. The specimen prepared at 650°C had a resistance of about 1 k. The resistance of as-cut specimens decreased with increase in relative humidity, but that of the polished specimen did not change significantly. The difference between as-cut and polished samples was explained by the differences in surface micro-structure.     

Novel process for cover glass with ideal stress distribution

Abstract — This paper proposes a new process to manufacture cover glass that overcomes a strength trade‐off between the face and the edge. In the process, alkali barrier films are deposited on glass faces before an ion exchange process in order to control face stress properties without inhibiting the edge strengthening. As a demonstration of the process, alkali‐alumino‐silicate glass sheets with sputter‐deposited SiO₂ films were chemically strengthened, and then their stress properties and strengths were investigated. As a result, thicker SiO₂ films cause lower face DOL (depth of strengthened layer), and it is observed that the faces have lower DOL than the edges. In strength tests corresponding to major fracture modes of smartphone cover glass, specimens with 80–100 nm films have more balanced face performance and better edge impact strengths than the no‐film specimen.     

Control of three-link underactuated manipulators using a switching method of fuzzy energy regions

In general, manipulators used for industry and in academic laboratories have actuators to drive each joint. On the other hand, underactuated manipulators handled by our research have some passive or free joints without actuators and brakes. We recently developed a switching method of fuzzy energy regions to control such manipulators. In such a method, it is necessary to design parameters related to energy regions and the gains of some partly stable controllers based on the computed torque method. Here, the switching method is applied for a three-link underactuated manipulator. We optimize such design parameters related to fuzzy energy regions by a genetic algorithm. The effectiveness of the present method is illustrated with some simulations. This work was presented in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007     

Evolutionary Learning of a Fuzzy Behavior Based Controller for a Nonholonomic Mobile Robot in a Class of Dynamic Environments

This paper presents an approach for evolving optimum behaviors for a nonholonomic mobile robot in a class of dynamic environments. A new evolutionary algorithm reflecting some powerful features in the natural evolutionary process to have flexibility to deal with changes in the environment is used to evolve optimum behaviors. Furthermore, a fuzzy set based multi-objective fitness evaluation function is adopted in the evolutionary algorithm. The multi-objective evaluation function is designed so that it allows incorporating complex linguistic features that a human observer would desire in the behaviors of the mobile robot movements. To illustrate the effectiveness of the proposed method, simulation results are compared using a conventional evolutionary algorithm.     

Modular fuzzy-neuro controller driven by spoken language commands.

We present a methodology of controlling machines using spoken language commands. The two major problems relating to the speech interfaces for machines, namely, the interpretation of words with fuzzy implications and the out-of-vocabulary (OOV) words in natural conversation, are investigated. The system proposed in this paper is designed to overcome the above two problems in controlling machines using spoken language commands. The present system consists of a hidden Markov model (HMM) based automatic speech recognizer (ASR), with a keyword spotting system to capture the machine sensitive words from the running utterances and a fuzzy-neural network (FNN) based controller to represent the words with fuzzy implications in spoken language commands. Significance of the words, i.e., the contextual meaning of the words according to the machine's current state, is introduced to the system to obtain more realistic output equivalent to users' desire. Modularity of the system is also considered to provide a generalization of the methodology for systems having heterogeneous functions without diminishing the performance of the system. The proposed system is experimentally tested by navigating a mobile robot in real time using spoken language commands.     

An interval algorithm for finding all solutions of non‐linear resistive circuits

In this letter, an efficient algorithm is proposed for finding all solutions of non‐linear (not piecewise‐linear) resistive circuits. This algorithm is based on interval analysis, the dual simplex method, and the contraction methods. By numerical examples, it is shown that the proposed algorithm could find all solutions of systems of 500–700 non‐linear circuit equations in acceptable computation time. Copyright © 2004 John Wiley & Sons, Ltd.