Dynamic simulation of hydrogen-based off-grid zero energy buildings with hydrogen storage considering Fanger model thermal comfort

In this study, some locations with different climates, off-grid zero energy buildings with hydrogen energy storage systems are designed, and transient analysis is conducted. These considered buildings supply their electricity consumption without using the electrical grid and PV panels or wind turbines. Also, they supply thermal comfort to occupants by using a vapor compression chiller and humidifier. Domestic hot water of occupants is supplied using solar collectors. For analyzing building's performance and objectives achievement, TRNSYS software is used. Also, for evaluating occupant thermal comfort, the Fanger model is used. The considered building is a one-story building with a 150 m² area. Four occupants are considered. Both of them are seated at rest, and another is seated with light working such as typing. Using the Fanger model equation and MATLAB software, the thermal comfort of occupants is determined. For domestic hot water consumption, verified profiles that vary during 24 h of the day are considered. Achieved results show that for humid and cold cities, PV panels with an area of 73 and 76 m² can be supplied the required electricity of considered building with four occupants and battery state of charge is higher than 50% and 10%, respectively. Moreover, with a suitable air conditioner system, the predicted percentage of dissatisfied (PPD) can be lower than 12% and 8% for humid and cold cities. Therefore, the building can be converted to a zero-energy building using its rooftop area.     

Cyclic thermal shock resistance for MgAlON–MgO composites obtained with additions of spent MgO–C brick: Microstructure characteristics,thermal shock parameter and thermal shock mechanism

Thermal shock parameters (R, R''', R'''' and R_st) of MgAlON–MgO composites obtained with additions of spent MgO–C brick were calculated using measured mechanical properties and thermal expansion coefficient, determining their resistance to fracture initiation and crack propagation. The cyclic thermal shock experiments of MgAlON–MgO composites performed from 1398 K to ambient temperature indicate that as number of thermal shock cycle increases, retained strength ratio of MgAlON and MgAlON–4.2 wt%MgO sharply decrease and then keep constant, while that of MgAlON–10.5 wt%MgO and MgAlON–15.7 wt%MgO slowly decrease. The reason for the difference is that MgAlON and MgAlON–4.2 wt%MgO show low value of R''' and R'''', and high value of R and R_st. Moreover, precipitation of impurity containing Fe may play a positive role in improvement of thermal shock resistance of MgAlON–MgO composites. MgAlON?4.2 wt%MgO has the maximum retained strength (55 MPa) even after 5 thermal shock cycles, which is expected to be used in the metallurgical industry.     

High-entropy titanate pyrochlore as newly low-thermal conductivity ceramics

Low-thermal conductivity ceramics play an indispensable role in maximizing the efficiency and durability of hot end components. Pyrochlore, particularly zirconate pyrochlore, is currently a highly promising and widely studied candidate for its extremely low thermal conductivity. However, there are still few pyrochlores that offer both stiffness, insulation, and good thermal expansion properties. In this work, the solidification method was innovatively introduced into the preparation of titanate pyrochlore, and combined it with the compositional design of high-entropy. Through careful composition design and solidification control, the high-density and uniform elements distributed high-entropy titanate pyrochlore ceramics were successfully prepared. These samples possess high hardness (15.88 GPa) and Young’s modulus (295.5 GPa), low thermal conductivity (0.947 W·m^?1·K^?1), excellent thermal expansion coefficient (11.6 ×10^?6/K) and an exquisite balance between stiffness and insulation (E/κ, 312.1 GPa·W^?1·m·K), in which the E/κ exhibits the highest value among the current reported works.     

Optical properties and radiation stability of SiO2/ZnO composite pigment prepared by co-sintering method

Thermal control coatings (TCCs) are an essential part of the thermal control systems in the spacecraft. Solar absorptance and emittance are the key performance parameters of TCCs. To develop an ultra-low solar absorption and stable inorganic TCCs for surface radiator, different TCCs were prepared by co-sintering ZnO and SiO₂ nanoparticles to form Zn₂SiO₄/SiO₂ pigment in this work, and the optical properties and radiation stability were systematically studied. It is found that the coating based on composite pigment has high reflectivity in the ultraviolet band and excellent optical performance possessing the low solar absorption of 0.06. In addition, the Zn₂SiO₄/SiO₂ coating demonstrates the highest proton and electron radiation stability because that SiO₂ between Zn₂SiO₄ particles acts as the relaxation center of the defects caused by radiation.     

Ternary type BaY2ZnO5: Eu3+ deep-red phosphor for possible latent fingerprint,security ink and WLED applications

Pc-WLEDs are considered to play a spectacular role in future generation light sources in view of their outstanding energy efficiency. In this regard, Eu³⁺ activated BaY₂ZnO₅ phosphor was prepared and investigated by XRD, PL and SEM analyses. Rietveld refinement analysis was carried out to confirm the structure of the synthesized phosphor. The prepared phosphor shows an intense red emission around 627 nm under excitation by near UV light. The ⁵D₀-⁷F₂ transition intensity of the prepared phosphor is three times higher compared to the commercial (Y,Gd)BO₃:Eu³⁺ red phosphor. The CIE colour coordinates of BaY₂ZnO₅:Eu³⁺ (9mol%) phosphor corresponds to be (0.6169, 0.3742) and it has a high 97.9 % colour purity. The obtained results reveal the utility of BaY₂ZnO₅:Eu³⁺ phosphor as an efficient red component in WLEDs, anti-counterfeiting and fingerprint detection applications.     

Influence of Co/W co-doping on structural and electrical properties of Na0.5Bi2.5Nb2O9 piezoelectric ceramics

Co/W co-doped Na_0.5Bi_2.5Nb_2-x(Co_1/3W_2/3)_xO₉ (NBNCW-x) ceramic samples were prepared by the conventional solid state reaction method. The electrical properties and crystal structure of the NBNCW-x ceramic samples were analyzed in detail. The XRD and Rietveld refinement results showed that the samples lattice distortion decreased with the increment of Co/W doping. The XPS results showed that the number of oxygen vacancies in the Na_0.5Bi_2.5Nb₂O₉ ceramics could be reduced by the substitution of a small amount of Co/W. The weakened lattice distortion and reduced number of oxygen vacancies of the Na_0.5Bi_2.5Nb₂O₉ ceramics synergistically contributed to its improved electrical properties. In particular, the Na_0.5Bi_2.5Nb_1.97(Co_1/3W_2/3)_0.03O₉ ceramic exhibited the best performance, and its T_c, d₃₃ and P_r were 780 °C, 24.9 pC/N and 12.6 μC/cm², respectively. The dielectric loss was only 3.3% at 550 °C. In addition, this ceramic exhibited excellent thermal stability, with the d₃₃ value of the ceramic being 95.2% of its original value when annealed at 750 °C. These properties indicate that the Co/W co-doped Na_0.5Bi_2.5Nb₂O₉-based ceramics have potential application in the high-temperature field.     

Thermal properties of hierarchical YSZ and LZO ceramic microspheres with multi-scaled voids investigated by using theoretical,experimental and simulation methods

Heat transfer within ceramic feedstock powders is still unclear, which impedes optimization of the thermal and mechanical properties of the thermal sprayed coatings. The microspheres (yttria-stabilized zirconia YSZ and lanthanum zirconate LZO) were prepared via the electro-spraying assisted phase inversion method (ESP). The thermal properties of the two ESP microspheres and a commercial hollow spherical powder (HOSP) were investigated by using theoretical, experimental, and simulation methods. Thermal conductivity of the single microsphere was estimated via a novel nest model that was derived from the Maxwell-Eucken 1 and the EMT model. Thermal conductivity of a single YSZ/LZO-ESP microsphere prepared at 1100–1200 °C was within 0.36–0.75 W/m K, which was ～ 20 % lower than that of a single YSZ-HOSP microsphere with a similar porosity. Heat flux simulation showed that high tortuosity around the multi-scaled voids of the ESP microsphere led to a more efficient decrease in thermal conductivity compared with total porosity.     

Thermal destratification of cryogenic liquid storage tanks by continuous bubbling of gases

This paper focuses on thermal destratification and pressurisation inside thermally stratified storage tanks by continuous gas bubbling. The primary purpose of doing these studies is to better understand the effect of bubble dynamics on thermal destratification and quantify the extent of destratification. The volume of fluid and interface compression method of OpenFOAM CFD code is utilised for the present analysis. Different values of inlet gas velocities (V_g), orifice diameters (d_o), and arrangement of the orifices in triangular and square fashion with different pitches (p/d_o) are considered. In addition, the effect of gravitational forces (g/g_e) on thermal destratification is also reported. For all these cases, the effectiveness of thermal destratification is quantified in terms of a newly defined parameter, the destratification index (I_d). For V_g = 1 m/s, the I_d value is maximum compared to lower V_g values. It is seen that when the gas velocity increased from 0.3 m/s to 1.0 m/s, the average effectiveness in thermal destratification (I_davg) and pressure at the ullage increased by 44.38% and by 64.81%, respectively. The I_davg and pressure at ullage increased by 96.29% and 14.91%, respectively, when the g/g_e ratio changed from 0.3 to 3. Compared to the triangular arrangement with p/d_o = 10, the calculated I_davg increased by 30.67% when gas inlets were arranged with a square pitch of 10. For p/d_o = 4, 6 and 8, the increments in I_davg are of the order of 12.86%, 19.43% and 21.92%, respectively, for gas inlets arranged in a square fashion as compared to the triangular arrangement. It is found that continuous bubbling with gas inlets arranged in square pitch p/d_o = 10 gives higher effectiveness in thermal destratification. Thus, by these studies, one can develop a thermal destratification mechanism with continuous bubbling for optimum performance. Also, these studies give an overall idea of sparger design for getting the correct gas flow rate for thermal destratification within the cryogenic liquid storage tanks.     

Hydrogen-rich gas generation via the exhaust gas-fuel reformer for the marine LNG engine

Reformed exhaust gas recirculation technology has attracted great attention in internal combustion engines. A platform of an exhaust gas-fuel reformer connected with the marine LNG engine was set up for generating on-board hydrogen. Based on the platform, effects of the methane to oxygen ratio (M/O) and reformed exhaust gas ratio (R_EG) from the reformer and excess air ratio (λ) from the engine on the components, hydrogen yield, thermal efficiency and reforming process of the reformer were experimentally investigated. Results shown that hydrogen-rich gases (reformate) can be generated by reforming the mixture of engine exhaust gas (about 400 °C) and methane supplied via the reformer with Ni/Al₂O₃ catalyst, and the hydrogen concentration of reformate was between 6.2% and 12.6% by volume. The methane supplied rate and λ affected the components and temperature of the reactant in the reformer, while R_EG changed the gas hour space velocity during the exhaust gas-fuel reforming processes, resulting in the difference in the components of the reformate and thermal efficiency. At the present experimental condition, the highest H₂ concentration reformate was generated under the M/O of 2.0, λ of 1.55 and R_EG of 6%.